VADDIO Wallview CCU HD-20 HD-SD Installation And User Manual - page 12
WallVIEW CCU HD-20
WallVIEW CCU HD-20 Manual 342-0181 Rev. C
Page 12 of 20
WallVIEW CCU HD-20
Part Numbers
WallVIEW CCU HD-20: 999-6957-000 (North America)
WallVIEW CCU HD-20: 999-6957-001 (International)
Vaddio ClearVIEW HD-20
Image Device
6.49mm diagonal (1/2.8 Type) Exmor High-speed CMOS Image Sensor
Picture Elements
3.27M pixels (Effective)
HD Resolutions
1080i/59.94/60, 1080/50i, 720p/59.94/60, 720/50p, 1080/30p and 1080/25p (SD Resolutions not Supported)
Lens
20x Optical Zoom, 11-Element HiLD™ (High Index Low Dispersion) Glass
Focal Length
F=4.7mm wide end to 94mm tele end
Horizontal Viewing
Angle (16:9 format)
1080i Mode: 2.9° tele end to 55.2° wide end
720p Mode: 1.93° tele end to 36.8° wide end (windowed - not scaled)
Invertible
Yes - With No Frame Delay
Video S/N Ratio
>50 dB
Minimum Illumination
1.6 LUX (F1.6, 50IRE)
Serial Control
Protocol
RS-232 (Modified VISCA)
Min. Object Distance
Wide End: .01m wide end, Tele end: 1.0m
Pan Range
+170 degrees to -170 degrees
Tilt Range
+90 degrees to -30 degrees
HD Video Select
16-Position Rotary Switch: Used to set HD Video Resolution Output
Camera Settings
10-Position Dip Switch: Settings for IR Select, Baud Rate 9600, Image Flip, Unpublished
Functions
Preset Positions
16 (internal), 6 recalled via IR Remote
Dimensions/Weight
7.81” (198.37mm) x 6.67” (169.42mm) x 7.057” (179.25. mm), 5.61 lbs. (2.54011744 kg.)
Quick-Connect CCU
Connectors
Power Connector: 5.5mm OD x 2.5mm ID
Power RJ-45: Supplies 36V to EZIM CCU
RS-232 IN RJ-45: Accepts RS-232 (bi-directional) controller information
RS-232 OUT RJ-45: Sends RS-232 (bi-directional) to camera
G/L OUT: NA
TALLY: 2-Pin Phoenix type spring cage connector
BNC Connector for Sync (not available on HD-20)
Video Outputs: BNC Connectors for HD Analog Component (YPbPr- HD ONLY)
Video RJ-45: Transports HSDS (diff) video from camera EZIM CCU Slot Card
Controls
Scene: (A, B and C), Detail, Red Gain, Blue Gain, AWB, Shift key between Pedestal and Knee,
Chroma, Gamma, Iris (Auto, Manual) and Gain
Camera Select Switch
All switches should be in the down position for HD-20
Video Adjustments
Y-Gain (luminance gain) for fine tuning over longer cable distances
Distance Compensation: 100’, 200’, 300’, 400’+
Cat-5e Cable Distance
Up to 500’ (152.4m)
Power Supply
36 VDC, 2.78 Amp
Dimensions
1-RU Rack Mount - 1.75” (43.688) H x 18.93” (480.822mm) W x 6” (152.4mm) D
CONCEAL Wall Mounting System for Vaddio ClearVIEW HD-20
Dimensions
5.125” H x 6.75” W x 10” D (13 cm x 17.15 cm x 25.4 cm)
Weight
Approx. 2.4 lbs. (1.1kg)
Compliance and CE Declaration of Conformity - HD-20 PTZ Camera