Apollo apollo apollo apollo dlg dlg dlg dlg discus launch g discus launch g discus launch g discus launch glider lider lider lider almost-ready-to-fly instruction manual specifications wing span: 1550mm (61in) length: 1050mm (41in) wing area: 24.5sq dm (358sq in) weight (kit): 350g (12.35oz) airfoil...
Www.Valuehobby.Com/apollo-dlg.Html 2 dear customer, congratulations on your purchase of apollo dlg from value hobby. We thank you for your generous support, and hope you enjoy your new airplane. At value hobby, we hope to offer competitive prices, good performance, and products that you can setup an...
Www.Valuehobby.Com/apollo-dlg.Html 3 safety in flying this is not a toy! It is a very high-performance rc airplane capable of high speeds and extreme maneuvers. It should only be operated by a competent pilot in a safe area with proper supervision. Only fly your aircraft in a safe, open area, away f...
Www.Valuehobby.Com/apollo-dlg.Html 4 recommended setup main parts of the airplane accessories and small parts not pictured configuration model qty radio 4 channel 1 speed control 3a brushless esc 1 recommended battery ′ lipo ″ gforce 20c 240mah 2s 7.4v lipo 1 servos 9g servos 4 y-harness universal s...
Www.Valuehobby.Com/apollo-dlg.Html 5 section 1: horizontal tail installation step1. Locate the horizontal tail wing.(the measurement shows the location of the mounting block). Step2. Remove the covering for the tail boom mounting block on the horizontal stabilizer. Step3. Mix some epoxy, and glue th...
Www.Valuehobby.Com/apollo-dlg.Html 6 section 2: vertical tail installation step1. Mark on the vertical fin where 70mm (2.8in) from the left edge of the vertical tail is. Step2. Insert the vertical tail into the tail boom and adjust the vertical tail to make the left edge of tail boom is aligned with...
Www.Valuehobby.Com/apollo-dlg.Html 7 section 3: elevator and rudder servo and linkage installation step1. Install two servos on the servo mounts. Step2. Thread the 790mm (31.1in) pushrod wire into the tail boom. The z-bend will be towards the tail. Step3. Install the servo arm with pushrod connector...
Www.Valuehobby.Com/apollo-dlg.Html 8 step7. Finish the elevator servo and linkage installation in the same way. Section 4: aileron servo and linkage installation. Step1. Locate the items shown in the picture. Step2. Glue two servo mounting blocks to the hatch inside the markings. Step3. Use two m2*8...
Www.Valuehobby.Com/apollo-dlg.Html 9 step7. Thread the clevis onto the aileron pushrod and connect the clevis to the servo arm. Mount the servo hatch to the wing using four m2*8mm (.3in) self-tapping screws. Step8. Use glue and two hinges to attach the aileron to the wing. Step9. With the pushrod wi...
Www.Valuehobby.Com/apollo-dlg.Html 10 section 6: battery installation install the battery into the fuselage as shown. Sponge can be used to prevent the battery from moving. Section 7: canopy installation use a m2*8mm (.3in) self-tapping screw to secure the canopy onto the fuselage. Section 8: throwi...
Www.Valuehobby.Com/apollo-dlg.Html 11 section 11: method of throwing step1. Your right index finger and middle finger should be wrapped around the peg. Step2. Stand with your left shoulder into the wind and the right wing tip on the ground. Step3. Start rotating to the left keeping the plane flat an...
Www.Valuehobby.Com/apollo-dlg.Html 12 www.Valuehobby.Com 2012-10-29.
