Dcm97k version 2 versie 2 version 2 separable meter : digital multimeter & ac current transducer afneembare meter : digitale multimeter & ac stroomtang mètre séparable : multimètre numérique & pince ampèremétrique ca user manual gebruikershandleiding manuel d'utilisation.
Dcm97k v2 gb 1 dcm97k -- separable meter : digital multimeter (dmm) & ac current transducer 1. Introduction thank you for buying the dcm97k ! We are confident that this multifunctional device will serve you well for many years to come. This is a separable meter consisting of a digital multimeter (dm...
Dcm97k v2 gb 2 part 1 : the digital multimeter (dmm) 1. Safety information this multimeter has been designed in accordance with ul1244 and iec-1010 concerning safety requirements for electronic measuring instruments with an overvoltage category (cat ii) and pollution 2. Follow all safety and operati...
Dcm97k v2 gb 3 figure 2 1.4. Maintenance l always disconnect the test leads from energised circuits before opening the housing or the battery compartment. L refrain from using the device and have it repaired by qualified personnel in case of malfunction. L do not use the meter unless the back panel ...
Dcm97k v2 gb 4 push the range key again to select the desired range. Hold the range key for two seconds in order to return to the autoranging mode. ÷ "fun."-key push the blue "fun."-key to alternate between ac & dc voltage measurement if the device is in the in the voltage mode. Push the key to alte...
Dcm97k v2 gb 5 3.2. Dc voltage range resolution accuracy 300mv 100µv 3v 1mv 30v 10mv 300v 100mv 600v 1v ± 0.7% of rdg -- 2 digits input impedance : 10m Ω overload protection : 600vdc or 600vrms ac 3.3. Ac voltage range resolution accuracy 3v 1mv 30v 10mv 300v 100mv 600v 1v ± 0.8% of rdg -- 3 digits ...
Dcm97k v2 gb 6 3.5. Diode and audible continuity test range description test condition display reads approximate forward voltage of diode forward dc current approx. 1.5ma. Reversed dc voltage approx. 3v built-in buzzer sounds if resistance Ω open-circuit voltage approx. 1.3v overload protection : 25...
Dcm97k v2 gb 7 4.2. Resistance measurement 1. Connect the red test probe to the "v- Ω " terminal and the black test lead to the "com" terminal. 2. Place the function switch in the " Ω " position and use the "fun."-key to select resistance measurement. 3. Make sure that the tested device is not under...
Dcm97k v2 gb 8 4.5. Current measurements see part two. 5. Accessories l ac current transducer l test lead (black) l test probe set l alligator clip (black) l user manual l 2 x 1.5v-battery 6. Battery replacement the batteries need to be replaced when the " "-sign appears on the lcd. Remove the screw...
Dcm97k v2 gb 9 figure 3 part 2 : the ac current transducer 1. Safety information the ac current transducer has been designed in accordance with iec1010 concerning safety requirements for hand-held current clamps. Use the device safely and keep it in good working order by following the instructions i...
Dcm97k v2 gb 10 2.2. Bottom view consult fig. 4 and follow the procedure outlined below to familiarise yourself with the device. Output plugs output terminals ó adjusting hole to be used exclusively by service personnel. 3. Specifications max. Accuracy is achieved during a one-year period after cali...
Dcm97k v2 gb 11 3.2. Electrical specifications range measure output accuracy 3a 0.030v 300a 30a 0.300v ± 3.0% ± 10 300a 3.000v ≥ 50a, ± 2.0% ± 5 4. Precautions and preparations for measurement 4.1. Do not apply voltage to the output plugs. 4.2. Do not expose this device to extreme temperatures or ex...
Dcm97k v2 gb 12 figure 5.
