VOKERA Mynute 28e User Instructions - page 9
9
Mynute
Obtain the options you require by using the SELECT
buttons to move the arrows in the display to the appropri-
ate positions. Your module is now working using the
standard programme times. If these suit your needs
there is nothing else to do.
You can temporarily override the normal switching times by
pushing a button marked ADVANCE. This switches ON to
OFF to ON as you require, but the normal programme
switching times will not be permanently affected. If you
want to make changes to the programme, it is suggested
you write them down before making the changes.
CHANGING YOUR PROGRAMME
With the module in the operating mode and the display
showing the actual time of day, press the SET button.
The display will again show SET CLOCK ? but this has
already been done so push the SET button again.
The displaywill again show SET PROG ? and as it is the
programme settings which are to be changed press the
YES button.
The display will show
NOTE: The grouping of days in this way is to enable
timings which apply to each and all of the weekdays to be
set first, followed by the opportunity to change one or
more timings for any single day.
If you wish to set timings which will be the same for each
weekday press the YES button.
The display will show
press YES and make the changes or press SET if no
changes are required.
The display will now show
press YES to make changes or SET if no changes are
required.
The display will now show
press YES if you wish to make changes to Monday
timings or press SET to change the display to SET TUE
PROG ? Again press YES to make changes to Tuesday
timings or continue to operate the SET button to access
each weekday in turn.
If you press YES to make changes to the settings for a
particular day, the display will firstly show SET CH
Press YES will allow changes to be made to the central
heating settings, but pressing SET will cause the display
to show SET HW Press YES will allow the changes to be
made to the hot water settings, a further press of SET will
move the display on the next day.
After any Friday changes have been made press SET
The display will show
This gives you the chance to set timings which will apply
to both weekend days by answering YES. Further
operation of the SET button accesses SAT and SUN for
individual timing changes.
Pressing SET after finishing any weekend programme
changes, or pressing SET in answer to SET PROG ?
returns the module to TEST ? Pressing SET again
display SET HOL ? Pressing SET again returns the
module to the normal operating mode.
If you answer YES to any of the detailed programming
questions the following steps will apply.
The display will show the time set for the first switch on
(ON1) to occur for the day(s) concerned. This can be
altered in steps of 10 minutes by use of the + and -
buttons. When the display is showing the time you want,
press SET and the OFF1 time will be seen.
Again changes may be made with the + and - buttons
before pressing SET to show the time for ON2 to occur.
After making any adjustments press SET
again to get the OFF2 time displayed. Repeat this
operation for the ON3 and OFF3 settings. This may be
set up to 23 hours 50 minutes after the first switch on time.
Further operations of the SET button will take you through
any remaining days of the week to be programmed before
arriving at the operating mode and ready to work at the
times you have set.
SWITCHING
MONDAY - FRIDAY SATURDAY - SUNDAY
H/W
C/H
H/W
C/H
6.30am
6.30am
6.30am
12 noon
10.30pm
6.30am
8.30am
8.30am
9.00am
9.00am
12 noon
ˇˇÄ
12 noon
12 noon
12 noon
12 noon
12 noon
4.30pm
4.30pm
4.00pm
4.00pm
11.00pm
10.30pm
11.00pm
OFF1-End of first timed period (OFF)
ON2-Start of second timed period (ON)
OFF2-End of second period (OFF)
ON3-Start of third period (ON)
OFF3-Final switch 'OFF'
ON1-Start of first timed period of day (ON)
SET
PROG ?
MON TUE WED THU FRI
MON TUE WED THU FRI
SET
PROG ?
CH
PROG ?
SET
MON
SET
PROG ?
SAT SUN
PROG ?
MON TUE WED THU FRI
SET
HW