WAGNER ProjectPro 119 Owner's Manual - page 34
30
WAGNER Project Pro 119 - 0418C
B) Startup
1. Removethegunfromtheplasticbag.Stirthewaterintothe
paint.
2. TurnthePRIME/SPRAYknobtoPRIME.
3. Plug sprayer in.
4. Turn the switch to ON (I).
5. TurnthePRIME/SPRAYknobtoSPRAY.Testthesprayerona
practice piece and begin spraying.
Figure 15 - Flushing the System
1. Lockthegunandremovespraytipassembly.Submerge
suction set into a bucket with appropriate cleaning solution
(a).
2. Place a waste container (b) next to the original material
container (c). The containers should be touching. Aim the
spray gun into the side of the original material container (c)
and hold the trigger.
3. While pulling the gun trigger, turn the pump ON (l), and turn
thePRIME/SPRAYknobtoSPRAYtopurgematerialfromthe
hose back into the original container. Keep holding trigger
through next steps.
4. Whencleaningsolutionflowsfromthespraygun,keep
holding the trigger and aim the spray gun into the side of the
wastecontainer(groundgunwithametalcontainerifflushing
withflammablesolvent).
5. Triggerthegununtilthefluidflowingoutofthegunisclear.
Youmayneedtodisposeandobtainnewcleaningsolution.
6. TurnthePRIME/SPRAYknobtoPRIMEandtriggergunto
relieve pressure.
Figure 16 - Cleaning the Spray Gun
1. Make sure the pump is switched OFF (O). Make sure
the PRIME/SPRAY knob is turned to PRIME. Unplug the
sprayer.
2. Removespraygunfromthepainthoseusingadjustable
wrenches.
3. Unclip the trigger guard (a) from the filter housing (b) by
pulling outward from the filter housing. Unscrew the filter
housing.
4. Removethefilter(c)fromthespraygunhousingandclean
with the appropriate cleaning solution (warm suds for water-
solublematerials,solventswithaflashpointofover21°Cfor
solvent-based spray).
5. Removespraytip(d)fromsprayguardassembly.Cleanspray
tip with a soft-bristled brush and the appropriate cleaning
solution. Be sure to remove and clean the washer (e) and
saddle seat (f) located in the rear of the spray tip assembly.
6. Replacethecleanedfilter,taperedendfirst,intothegun
housing. The tapered end (g) of the filter must be loaded
properly into the gun. Improper assembly will result in a
pluggedtipornoflowfromthegun.
7. Install spray tip (d), saddle seat (f) and washer (e), and replace
spray guard assembly.
8. Thread the spray gun back onto the paint hose. Tighten with
a wrench.
Figure 17 - Cleaning the Suction Set
1. Lock the gun and turn the pump OFF (O). Turn the PRIME/
SPRAY knob to PRIME.
2. Removethesuctionhosefromtheinletvalve.Removethe
return hose, by pushing the blue circlip ring up and pulling
the hose down simultaneously. Coarsely clean the outside of
both hoses with a suitable cleaning solution.
3. Clean the thread of the inlet valve (a) with a cloth.
4. Carefully remove the filter disc (b) from the suction filter using
pliers, and clean both.
5. After cleaning the suction unit screw the suction hose back onto
the inlet valve and replace the return hose in the return connection
piece.
6. Submergethesuctionhoseandreturntubeintoabucketof
new cleaning solution.
7. TurnthePRIME/SPRAYknobtoPRIME.TurnthepumpON(l),
and trigger the gun into a waste container to relieve pressure.
8. Letthepumpcirclulatecleaningsolutionthroughthesuction
set for 2-3 minutes. Turn the pump OFF.
Figure 18 - Long-Term Storage
1. Fill a cup or another container with a little separating oil or
a light, common household oil. Hold the cup under the inlet
valve. The valve opening must be completely in the oil bath.
2. Place a rag over the spray hose port, and turn the switch ON
(l). When the oil has been pumped from the cup, turn the
pump OFF (O).
3. FullyinserttheSureflo™valve.
4. Wipe the entire unit, hose and gun with a damp cloth to
removeaccumulatedpaint.Replacethehighpressurehoseto
the paint hose port.
Figure 19 - Cleaning the Inlet Valve
i
Cleaning or servicing the inlet valve may be required if
the unit has priming problems. Priming problems may
be prevented by properly cleaning the sprayer and
following the long-term storage steps.
1. Removethesuctionhoseandreturntube.Loosenthefittingas
shown(a)andremovetheSureflo™valvesolenoid.
Make sure that the O-ring does not get lost.
2. Removetheinletvalveunit(b)fromthebasicunitwithan
adjustable wrench. Visually inspect the inside and outside
of the inlet valve assembly. Clean any paint residue with the
appropriate cleaning solution.
3. Replaceinletvalveassemblybyscrewingitintothesprayer.
4. ReplaceSureflo™valvesolenoid.
Figure 20 - Folding the Cart
1. Turn the knobs on both sides of the carriage in the DOWN
arrow direction as far as the stop. Hold the handle firmly while
doing this, as otherwise it will drop down.
2. Fold the handle down. Be careful not to pinch the power cord
with the cart.
Danger
Attention! When the feet are retracted the wheels
can easily roll away, causing the unit to lose
balance. Hold the basic unit firmly at the container
holder during the next few steps, and block a wheel
with your foot.
3. Pullthefootlockupandretractthefeet.Securethefeetagain
with the foot lock. Place the basic unit carefully on the ground.