- DL manuals
- Waldorf
- Ranges
- RN8110GE
- Installation And Operation Manual
Waldorf RN8110GE Installation And Operation Manual
Summary of RN8110GE
Page 1
I n s t a l l a t i o n a n d o p e r a t i o n m a n u a l rn8110ge rn8110gec gas target top range / electric ovens date purchased serial number dealer service provider 229244-16 for use in gb & ie gpd.Sunwayinfo.Com.Cn gpd.Sunwayinfo.Com.Cn.
Page 2
The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless authorized previously in writing by the manufacturer. In line with policy to continually develop and improve its products, moffat ltd. Reserves the right to change the specifications and desig...
Page 3
1 waldorf gas target top electric oven range rn8110ge gas target top / electric static oven range. Rn8110gec gas target top / electric convection oven range. Introduction .............................................................................................. 2 specification .....................
Page 4
2 we are confident that you will be delighted with your waldorf gas target top / electric oven range, and it will become a most valued appliance in your commercial kitchen. To ensure you receive the utmost benefit from your new waldorf appliance, there are two important things you can do. Firstly: p...
Page 5
3 specifications model numbers covered in this specification rn8110ge gas target top / electric static oven range - 900 mm. Rn8110gec gas target top / electric convection oven range - 900 mm. General a commercial heavy duty, gas fired target top having a high output, two stage double-ring iron cast ...
Page 6
4 gas connection gas supply connection point is located at the rear of the appliance, approximately 130mm from the right hand side, 31mm from the rear and 655mm from the floor and is reached from beneath the appliance. An optional underside connection is available. (refer to the ‘dimensions’ section...
Page 7
5 dimensions dimensions rn8110ge / gec gpd.Sunwayinfo.Com.Cn gpd.Sunwayinfo.Com.Cn.
Page 8
6 installation requirements note: • it is most important that this appliance is installed correctly and that operation is correct before use. Installation shall comply with local gas, electrical and health and safety requirements. • this appliance shall be installed with sufficient ventilation to pr...
Page 9
7 7. Components having adjustments protected (e.G. Paint sealed) by manufacturer are only allowed to be adjusted by an authorised service agent. They are not to be adjusted by the installation person. Note: do not obstruct or block the appliances flue. Never directly connect a ventilation system to ...
Page 10
8 gas connection note: all gas fitting must only be carried out by an authorised person. 1. It is essential that the gas supply is correct for the appliance to be installed and that adequate supply pressure and volume are available. The following checks should therefore be made before installation:-...
Page 11
9 electrical connection note: all electrical connections must only be carried out by an authorised person. Each appliance should be connected to an adequately protected power supply and isolation switch mounted adjacent to, but not behind the appliance. This switch must be clearly marked and readily...
Page 12
10 commissioning 1. Before leaving the new installation; a. Check the following functions in accordance with the operating instructions specified in the ‘operation’ section of this manual. • light the target top pilot burner. • light the target top main burner. • check the target top low fire burner...
Page 13
11 operation guide 1. Waldorf appliances have been designed to provide simplicity of operation and 100% safety protection. 2. Improper operation is therefore almost impossible, however bad operation practices can reduce the life of the appliance and produce a poor quality product. To use this applia...
Page 14
12 lighting the pilot burner (target top) 1. Remove centre casting with the casting removal tool. 2. Depress the control knob and rotate anti-clockwise to the ‘pilot’ position. 3. With the control knob depressed, manually light the pilot burner located in front of the main burner. 4. Hold in the con...
Page 15
13 oven the oven is fitted with top and bottom elements. The thermostat maintains the overall oven temperature. The top element is further controlled by the oven top heat control. Convection ovens (rn8110gec) are fitted with a circulation fan. Note: the thermostat on the static oven provides overall...
Page 16
14 general clean the target top / range regularly. A clean appliance looks better, will last longer and will perform better. Carbonised grease on the cooking surface will hinder the transfer of heat from the cooking surface to the food. This will result in loss of cooking efficiency. Do not use wate...
Page 17
15 cleaning and maintenance target top a. This should be kept clean of any build up of spillage’s of food. Provided the cast iron work surface is regularly used it will maintain itself in good condition with no special cleaning requirements being necessary. B. Clean any food residue and spillage fro...
Page 18
16 fault finding this section provides an easy reference guide to the more common problems that may occur during the operation of your appliance. The fault finding guide in this section is intended to help you correct, or at least accurately diagnose problems with your equipment. Although this secti...
Page 19
17 wiring schematic rn8110ge gpd.Sunwayinfo.Com.Cn gpd.Sunwayinfo.Com.Cn.
Page 20
18 wiring schematic rn8110gec gpd.Sunwayinfo.Com.Cn gpd.Sunwayinfo.Com.Cn.
Page 21
19 wiring schematic wiring layout for static oven wiring layout for convection oven gpd.Sunwayinfo.Com.Cn gpd.Sunwayinfo.Com.Cn.
Page 22
20 gas conversion and specifications conversion procedure note: • these conversions should only be carried out by qualified persons. All connections must be checked for leaks before re-commissioning the appliance. • adjustment of components that have adjustments / settings sealed (e.G. Paint sealed)...
Page 23
21 gas conversion and specifications pilot burner 1. To remove the pilot burner, disconnect the gas supply tube from the base of the pilot burner. 2. Remove the bolt securing the retaining plate holding the pilot burner and thermo couple to the mounting bracket. Remove the retaining plate. 3. The pi...
Page 24
22 gas conversion and specifications gas regulator note: the regulator supplied is convertible between natural gas and lpg, but it’s outlet pressure is fixed ex-factory and is not to be adjusted. 1. Ensure that the gas supply is turned ‘off’ at the mains. 2. Unscrew the hexagonal cap (23mm a/f) from...
Page 25
23 gas conversion and specifications gas specifications - australia / new zealand only - uk only appliance classification category: ii 2h3p. Flue type: a 1. * the burner operating pressure is to be measured at the target top hob manifold test point with the target top burner (inner and outer ring) o...
Page 26
24 replacement parts list when ordering replacement parts, please quote the part number and the description as listed below. If the part required is not listed below, request the part by description and quote model number and serial number which is shown on the rating plate. Target top controls 2288...
Page 27
25 general 227012 centre casting. 227013 half plate casting. 014997 casting removal tool. 227892 side rack lh. 227893 side rack rh. 227896 oven rack. 228571 index mark moulding. 227963 neon orange. 227962 neon green. 227850 leg (150 mm) adjustable. 229674 rear roller assy. Accessories 228800 ranges ...
Page 28
26 gpd.Sunwayinfo.Com.Cn gpd.Sunwayinfo.Com.Cn.
Page 29
27 gpd.Sunwayinfo.Com.Cn gpd.Sunwayinfo.Com.Cn.