Waring MX1300XTP Operating Manual - page 5
8
9
RESTORING FACTORY-SET BEVERAGE STATIONS
1. To restore factory-set default beverage stations, press both
Speed Up
and Speed Down
buttons. LCD will prompt ADD NEW
PROGRAM.
2. Press
button.LCDwillpromptRESTOREDEFAULTPROGRAMS.
3. Press
button to confirm and save. The LCD will display the logo for
3 seconds.
4. The unit will return to standby mode and the LCD will prompt PRESS
ANYBUTTONTOBLEND.
NOTE: The Stop
key will abort this process at any point before
restoring default programs is confirmed.
DRINK COUNTER
Your reprogrammable blenders are equipped with a drink counter to keep
track of daily drink totals and total drink counts for your machine. To display
the counts, hold program buttons
&
simultaneously for 3 seconds.
Your display will read:
DAILYCOUNTXXXX
TTLCOUNTXXXXX
DailyCountwilldisplaythenumbersofdrinksmixedperday.TotalCount
is the accumulation of all drinks made since first use of the blender.
The Daily Count can be reset by holding in program buttons
&
simultaneouslyfor3secondsthen,pressing(ON/OFF)buttonfor3seconds.
DailyCountwillresettozeroandTotalCountwillremainunchanged.
IfTotalCountneedstobereset,callyournearestWaringauthorizedservice
facility for information.
NOTE: Use of the PULSE features will not add to the daily or total drink
counts.
RESETTING THERMAL PROTECTION
• Yourblenderisequippedwithanautomaticresetfunctiontoprotectthe
motor from overheating.
• Ifyoublenderstopsrunningunderheavyuse,turnthepowerswitchto
Offandunplugthepowercord.Emptytheblendercontainerofall
its contents and allow between 5 and 30 minutes for the motor to
cool down.
• Plugthepowercordbackintotheoutletandcontinueblending.
• Ifyourblenderdoesnotfunctionproperlyfollowingthisprocedure,
discontinue use and contact a certified Waring Customer Service Center.
IMPORTANT - HOT BLENDING INSTRUCTIONS
Tominimizethepossibilityofbeingscaldedwhenblendinghotmaterials,
the following precautions and procedure must be observed.
• Hotmaterialsarethosethatare100°F(38°C)orhotter.
• Limittheamountofmaterialsprocessedto1pint.
• Completelyremovethecenterportionofthetwo-piececontainerlidbefore
startingmotor(thiswillallowventingoftherapidlyheatedandexpanded
air inside the container when blender is running).
• Alwaysstartblendingonlowestspeedsetting,andthenprogressto
desired speed.
• Neverstanddirectlyoverblenderwhenitisbeingstartedorwhileit
is running.
SOUND ENCLOSURE (for MX1500XTX Version)
YourMX1500XTX/MX1500XTP/MX1500XTSblenderisequippedwitha
heavy-duty polycarbonate sound enclosure to reduce noise level while
blending. This sound enclosure is removable and dishwasher safe.
To remove the sound enclosure, follow these steps:
1. Opensoundenclosureandremoveblendercontainer.
2. Remove front portion of sound enclosure by disengaging both sides at
the pivot point.
3. Remove rubber jar pad.
4. Remove 3 screws from blender base and remove sound enclosure.
NOTE: To replace sound enclosure, follow above steps in reverse.
TURNING OFF YOUR BLENDER
Whether your blender is in standby mode, new programming mode, or
themotorisrunning,pressingtheOn/Off
button will stop the unit
from running and will turn the power off. The LCD display will turn off.
NOTE:Allprogramsandcurrentsettingswillberestorednexttimeyou
turn unit on.
CLEANING AND SANITIZING INSTRUCTIONS
THEBLENDERCONTAINERMUSTBECLEANEDANDDRIEDAFTEREACH
USEACCORDINGTOTHEFOLLOWINGINSTRUCTIONS.FAILURETODO
SOMAYALLOWRESIDUESOFPROCESSEDMATERIALTOCOLLECTON
THEINTERNALSEALSOFTHEBLADEASSEMBLY,RENDERINGTHEM
INEFFECTIVE.
• Wash,rinse,sanitizeanddrycontainerpriortoinitialuseandwheneverit
will not be used again within a period of one hour.
• Washandrinsecontaineraftereachuse.