WeatherTech AlloyCover Installation Instructions And Owner's Manual

Summary of AlloyCover

  • Page 1

    Thank you for purchasing the alloycover ™ from weathertech ® . Manufactured with pride using superior quality materials and workmanship. With proper care, your cover will provide years of service and enjoyment. Notice to installer: it is recommended instructions are read before installation, even if...

  • Page 2: Preparation

    2 note on bed liners: with an under-the-rail drop-in bed liner, installation is possible with minimal trim/cutting of bed liner at front corner of box and back by tailgate to allow side rail to install properly. Considerable trim/cutting is required with an over-the-rail drop-in bed liner. Note: for...

  • Page 3

    2 3 note: some installs require special instructions. Follow the special instructions for rail attachment along with these standard instructions. A. Position side rail with weather strip against inside lip of box and front catch towards front of box. Push rail forward until it touches front of box. ...

  • Page 4: Step 2: Installing Cover

    4 step 2: installing cover d. Unfold rear panel towards tailgate. Hooks on rear panel will automatically engage rear catch on each side rail. Latches will automatically engage each side rail at rear of box. Note: make sure all latches fully engage the side rails when closing cover. C. Unhook storage...

  • Page 5: Troubleshooting

    4 5 problem gap between cover and tailgate rails set too high (refer to step 1c) top of tailgate hits cover when attempting to close rails set too low at rear of cover, raise rails at rear of box until cover no longer interferes with tailgate operation (refer to step 1c) latch doesn’t engage check s...

  • Page 6: Closing Tri-Fold Cover

    6 important: to avoid any damage or misalignment of hinge points, close cover in a smooth, fluid manner. C. Unfold rear panel towards tailgate. Make sure all latches engage side rails when closing cover then close tailgate. B. Unfold middle panel towards tailgate. Closing tri-fold cover a. Unhook st...

  • Page 7: Opening Tri-Fold Cover

    6 7 important: to avoid any damage or misalignment of hinge points, open cover in a smooth, fluid manner. B. Fold middle panel on top of front panel. Opening tri-fold cover c. Securely fasten storage clips on both sides to store the cover. A. Open tailgate, lightly pull synthetic cord to release lat...

  • Page 8

    8 a. With cover completely open and storage clips secured, pull synthetic cord on front panel and lift rear of cover up 1" above rails (figure 1). B. Slide cover back to disengage hooks then lift to remove (figure 2). Removal and reinstall of cover a. Place leading edge of front panel on rails at fr...

  • Page 9: Inspection And Maintenance

    8 9 • keep cover closed when not in use, avoid storing cover in its folded position for long periods of time. • make sure cover is properly latched while traveling and before entering automatic drive-through car washes. • when cleaning, for best results use mild liquid soap and water. Never clean wi...

  • Page 10: Safety Information

    10 • do not tow vehicle backwards with cover on your truck. • do not cover cargo that is higher than the cover. • do not place object(s) on or against the cover or its framework at any time. • always secure cargo so it cannot shift and damage the cover or its parts. • remove any snow or debris from ...

  • Page 11: 3 Year Warranty

    10 11 weathertech ® extends the following 3 year warranty to the original retail purchaser of this alloycover ™ : weathertech ® warrants its covers to be free from defects in material and workmanship, as long as the original purchaser owns the truck on which the cover was originally installed and as...

  • Page 12: For Your Records

    12 ©2017 macneil ip llc. 0317 date purchased: location of purchase: serial number: (located on decal under rear panel by tailgate) for your records made in usa questions? (800) 441-6287 .Com 1 macneil ct, bolingbrook, il 60440