- DL manuals
- Webasto
- Automobile Accessories
- CARBONTECH
- Installation Instructions And Owner's Manual
Webasto CARBONTECH Installation Instructions And Owner's Manual
Summary of CARBONTECH
Page 1
Presents carbontech™ seat heater installation instructions and owner’s manual single seat application with two 12” x 26” heating pads (hi/lo/off round illuminated switch) p/n 300202-mwa.
Page 3
Page 3 of 20 installation preparation & general notes: 1. Seat heater system will not work on seats manufactured using the “foam in place” (trim cover glued to foam pad) method of trim cover attachment. 2. If the vehicle is equipped with an anti-theft radio, the radio code must be written down prior...
Page 4
Page 4 of 20 installation: open box and remove contents. Check to make sure that the following parts are included within kit: qty description part number 2 12”x 26” seat heater pad 30-0108-mw 1 wire harness assembly 30-4200004 1 switch assembly 30-0213-mw 4 black tape strips 30-0110-mw 4 gold tape s...
Page 5
Page 5 of 20 7. Measure the width of the center seat area between the longitudinal seams. Note: the width must be at least 250 mm (10 in). The heating pad cannot contact the side seams of the seat. If it does make contact, the seat heater cannot be installed. See fig 3 8. Position the heating pad wi...
Page 6
Page 6 of 20 11. Reposition heating pad onto cushion foam. Make sure thermostat is in the correct location. (see step 9) using the supplied gold double sided tape, attach the back edge of the heating pad to the cushion foam. With the pad attached at the rear, determine the final length. Note: make s...
Page 7
Page 7 of 20 seat heater pad wire harness routing/attachment: 1. Route wires from cushion & back to underside of seat. Use supplied wire ties to fasten harness to seat. Warning: make sure attachment locations will not interfere with any seat movement. Seat heater switch: 1. With the seat still remov...
Page 8
Page 8 of 20 4. Install seat mounting fasteners and torque to manufacturers recommended specifications. 5. Re-connect the negative battery cable and test function the seat heater system. 6. Re-check all systems and accessories where components were removed or relocated during the installation proces...
Page 9
Page 9 of 20 troubleshooting: if system does not heat up or no indication of power. - check fuse in seat heater harness and vehicle. - temperature of seat may be above the preset thermostat temperature and will not allow it to come on. (i.E.: sun shining on seat) - if the light on the heated seat sw...
Page 10
Page 10 of 20 seat heater system wiring schematic: carbontech™ seat heater specification (290mm) heater pads: size 645 x 290mm thickness 1.3mm heating power 0.050 watt/sq. Cm @ 13.8 volts total heating power 71 watts @ 13.8 volts electrical resistance 2.67 ohm +/- 10% electrical current 5.17 amps @ ...
Page 11
Page 11 of 20 wiring: material pvc/cu specification 2000/53/eg iso 6722 din en 60684-2 (vde 0341-2) din en 60352-2 din vde 0298 weight 0.033 kg content per kit 1 relay: type change over relay continuous rating 20 amps @ 12 volts short time rating 40 amps @ 12 volts voltage drop (20 amp) pressure on ...
Page 12
Page 12 of 20 functional principle of carbontech™ system: each heater pad is an electrical resistor. A seat heater kit contains two (2) heater pads: one (1) for the cushion and one (1) for the bag. To realize two (2) heating levels, the two (2) pads are connected serial for the “low” position and pa...
Page 13
Page 13 of 20 warranty instructions and procedures carbontech™ carries a one year limited warranty beginning from the date of installation. The warranty covers proven fabrication and materials deficiencies. Not covered in the warranty are damages resulting from: ¾ improper handling of components and...
Page 14: Notice to Users
Page 14 of 20 notice to users the seat heater is designed to control the temperature of the lower and upper seat segment of the front seats. Proper temperature control of the vehicle seat increase the driver‘s comfort and enhances basic health. The seat heater operates in two power levels and can on...
Page 15
Page 15 of 20 features – functions – benefits ¾ the carbontech™ seat heater system is made from the highest quality carbon fiber material. ¾ higher density of carbon fiber mesh produces approx. 7% higher heating capacity and ramp-up times over other competitive products. ¾ patented solution of a tef...
Page 16
Page 16 of 20 warranty instructions and procedures webasto product inc. Carries a one year limited warranty beginning from the date of installation. The warranty covers proven fabrication and materials deficiencies. Not covered in the warranty are damages resulting from: ¾ improper handling of compo...
Page 17: Safety Advice
Page 17 of 20 safety advice ¾ do not place any heavy, sharp or pointed objects on the seats. ¾ any fluid spilled on the seats may destroy the seat heater and may cause damage to the vehicle. Never operate the seat heater while the seats are wet or soaked with fluid. ¾ do not keep insulating material...
Page 18
Notes:.
Page 19
Notes:.
Page 20
Webas to product n.A., inc. 15083 north road fenton, mi 48430 technical assistance hotline usa: (800) 860-7866 canada (800) 667-8900 www.Webasto.Us www.Techwebasto.Com.