WeBoost EQO User Manual - ______
8
CELL PHONE SIGNAL BOOSTER
______
Specifications
eqo Booster
Product Number
U473020
Model Number
460032
FCC ID:
PWO460032
IC:
4726A-460032
Connectors
SMA-Female
Antenna Impedance
50 Ohms
Frequency
698-716 MHz, 729-756 MHz, 777-787 MHz, 824-894 MHz, 1850-1990 MHz, 1710-1755/2110-2155 MHz
Passband Gain (nominal)
700 MHz
Band 12/17
61
700 MHz
Band 13
62
800 MHz
Band 5
62
1700/2100 MHz
Band 4
68
1900 MHz
Band 2
70
20 dB Bandwidth (MHz)
700 MHz
Band 12/17
700 MHz
Band 13
800 MHz
Band 5
1700/2100 MHz
Band 4
1900 MHz
Band 2
Typical
31.8
32.1
37.9
79.9
81.9
Maximum
35.4
35.6
39.0
83.0
85.1
Maximum Power
Power output for single cell
phone (Uplink) dBm
700 MHz
Band 12/17
23.94
700 MHz
Band 13
24.19
800 MHz
Band 5
23.49
1700/2100 MHz
Band 4
24.55
1900 MHz
Band 2
23.61
Power output for single cell
phone (Downlink) dBm
700 MHz
Band 12/17
11.64
700 MHz
Band 13
11.92
800 MHz
Band 5
12.1
1700/2100 MHz
Band 4
11.9
1900 MHz
Band 2
9.5
Power output for multiple
received channels (Uplink) dBm
Maximum Power
No. Tones
700 MHz
Band 12/17
700 MHz
Band 13
800 MHz
Band 5
700 MHz
Band 4
1900 MHz
Band 2
2
20.7
19.9
23.4
21.2
19.1
3
17.1
16.3
19.9
17.7
15.5
4
14.6
13.8
17.4
15.2
13.0
5
12.7
11.9
15.4
13.3
11.1
6
11.1
10.3
13.9
11.7
9.5
Power output for multiple
received channels (Downlink) dBm
Maximum Power
No. Tones
700 MHz
Band 12/17
700 MHz
Band 13
800 MHz
Band 5
2100 MHz
Band 4
1900 MHz
Band 2
2
12.7
13.3
11.8
11.9
12.6
3
9.2
9.8
8.2
8.4
9.1
4
6.7
7.3
5.7
5.9
6.6
5
4.8
5.4
3.8
4.0
4.7
6
3.2
3.8
2.2
2.4
3.1
Noise Figure
5 dB nominal
Isolation
> 110 dB
Power Requirements
5V/2.5A
The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met.
Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without
factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order
to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until
a signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal
Booser will automatically reduce the gain on that specific band.
The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier
signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can
cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by an
attenuator at the output of the device.