1. DL manuals
  2. Weider
  3. Other
  4. Pro 9635
  5. User Manual

Weider Pro 9635 User Manual

Other manuals for Pro 9635: User Manual, Manual, Manual
Manual is about: Canadian English Manual

Summary of Pro 9635

  • Page 1

    User’s manual model no. Wesy9635c.3 serial no. Write the serial number in the space above for reference. Serial number decal (under seat) caution read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Questions? As a manufacturer, w...

  • Page 2: Table of Contents

    2 table of contents warning decal placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 important precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 3: Warning:

    3 1. Read all instructions in this manual and in the accompanying literature, and all warn- ings on the weight system, before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions. 3. The weight sy...

  • Page 4: Before You Begin

    4 before you begin foot plate low pulley station high pulley station lat bar leg lever butterfly arms military press arm press arm weight stacks backrests vkr arms leg press plate thank you for selecting the versatile weider ® pro 9635 weight system. The weight system offers a selec- tion of weight ...

  • Page 5: Assembly

    5 assembly 1 8 8 11 1 4 3 3 1 5 1. Before beginning assembly, make sure that you have read and understand the information in the box above. Locate and open the parts packet labeled “frame assembly.” insert six m8 x 62mm carriage bolts (1) up through the stabilizer (5). Insert two m8 x 62mm carriage ...

  • Page 6

    6 2. Slide the vkr upright (74) and the leg press upright (56) onto the indicated m8 x 62mm carriage bolts (1) in the stabilizer (5). The high side of the brackets on the vkr upright and leg press upright should be on the side shown. Hand-tighten four m8 nylon locknuts (3) onto the carriage bolts. D...

  • Page 7

    7 4. Attach the top frame (55) to the vkr upright (74) and the leg press upright (56) with two m8 x 67mm bolts (11) and two m8 nylon locknuts (3). Attach the top frame (55) to the front upright (42) with two m8 x 67mm bolts (11), two m8 washers (8), and two m8 nylon locknuts (3). 5. Slide the rear s...

  • Page 8

    8 7. Press a weight tube bumper (64) into the end of a weight tube (63). Insert the weight tube into the front stack of weights (25). Make sure that the pin on the weight tube is sitting in the pin groove in the top weight. Lubricate the inside of the holes in a top weight (65). Set the top weight o...

  • Page 9

    9 9. Attach the upper ends of the short weight guides (73) to the top frame (55) with an m8 x 150mm bolt (60), two 13mm x 19mm spacers (61), and an m8 nylon locknut (3). Attach the upper ends of the long weight guides (62) to the top frame (55) with an m8 x 150mm bolt (60), two 13mm x 19mm spacers (...

  • Page 10

    10 12. Attach the press arm (46) to one side of the press frame (17) with two m8 x 63mm bolts (22) and two m8 nylon locknuts (3). Assemble the other press arm (46) in the same manner. 13. Identify the right arm (48) and the left arm (47). Note the position of the welded bracket on each arm. Arm iden...

  • Page 11

    11 15. See the inset drawing. Attach the military press arm (84) to the pivot arm (101) with two m8 x 57mm bolts (33) and two m8 nylon locknuts (3). Attach the pivot arm (101) to the vkr upright (74) with an m10 x 83mm bolt (67) and an m10 nylon locknut (21). 16. Locate and open the parts packets la...

  • Page 12

    12 18. Wrap the high cable (58) around a “v”-pulley (50). Attach the “v”-pulley and a long cable trap (31) to the indicated bracket on the front upright (42) with an m10 x 57mm bolt (86) and an m10 nylon locknut (21). Make sure that the long cable trap is positioned to hold the cable in place. 19. R...

  • Page 13

    13 22. See the inset drawing. Route the high cable (58) under a 90mm pulley (15). Attach the pulley and a cable trap (66) to the upper hole in a long “u”-bracket (57) with an m10 x 47mm bolt (12) and an m10 nylon locknut (21). Make sure that the cable is in the groove of the pulley and that the cabl...

  • Page 14

    14 25. Route the low cable (23) under a 90mm pulley (15). Attach the pulley and a cable trap (66) to the lower hole in the front upright (42) with an m10 x 92mm bolt (88), an m10 washer (9), and an m10 nylon locknut (21). Make sure that the cable trap is turned to hold the cable in place. 26. Route ...

  • Page 15

    15 28. Attach the end of the low cable (23) to the long “u”-bracket (57) with an m8 nylon locknut (3) and an m8 washer (8). Do not completely tighten the locknut. It should be threaded onto the end of the cable so that only two threads are showing past the locknut, as shown in the inset drawing. 29....

  • Page 16

    16 31. Wrap the military press cable (72) over a 90mm pulley (15). Attach the pulley to the top frame (55) with an m10 x 47mm bolt (12) and an m10 nylon locknut (21). See the inset drawing. Wrap the military press cable (72) under a 90mm pulley (15). Attach the pulley and a cable trap (66) to the br...

  • Page 17

    17 33. See inset drawing a. Route the military press cable (72) under a 90mm pulley (15). Attach the pulley and a cable trap (66) to the upper hole in the long “u”-bracket (57) with an m10 x 47mm bolt (12) and an m10 nylon locknut (21). Make sure that the cable is in the groove of the pulley and tha...

  • Page 18

    18 35. Attach the press bracket (94) to the leg press arm (96) with an m10 x 78mm bolt (105) and an m10 nylon locknut (21). Wrap the leg press cable (99) around a 90mm pulley (15). Attach the pulley to the press bracket (94) with the m10 x 47mm bolt (12) and an m10 nylon locknut (21). Slide an m10 w...

  • Page 19

    19 38. Orient the front backrest (41) as shown. Attach the backrest to the front upright (42) with two m6 x 63mm screws (43) and two m6 washers (10). 39. Insert an m6 x 50mm carriage bolt (38) through the center hole in the seat plate (37). Attach the seat plate to the seat (13) with two m6 x 16mm s...

  • Page 20

    20 42. Insert a pad tube (28) into the front seat frame (36). Slide a foam pad (30) onto each end of the pad tube. Insert the other pad tube (28) into the leg lever (29). Slide a foam pad (30) onto each end of the pad tube. 43. Locate and open the parts packet labeled “vkr assembly.” attach the left...

  • Page 21

    21 45. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in how to use the weight system, beginning on page 22 of this manual. Before using the weight system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. ...

  • Page 22

    22 how to use the weight system the instructions below describe how each part of the weight system can be adjusted. Refer to the exercise poster accompanying this manual to see how the weight system should be set up for each exercise. Impor- tant: when attaching the lat bar or nylon strap, make sure...

  • Page 23

    23 attaching and removing the seat to attach the seat (13), set the bracket on the front seat frame (36) onto the indicated pins on the front upright (42). Attach the seat frame to the front upright with the m8 x 70mm carriage bolt (14) and the seat knob (40). For some exercises, the seat (13) must ...

  • Page 24: Weight Resistance Chart

    24 weight resistance chart this chart shows the approximate weight resistance at each weight station. “top” refers to the 6.5 lb. (2.9 kg) top weight. The other numbers refer to the 12.5 lb. (5.7 kg) weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm. Weight ...

  • Page 25

    Troubleshooting and maintenance inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. Tightening the cables woven cable, the type of cable used o...

  • Page 26: Cable Diagrams

    26 cable diagrams the cable diagrams on these pages show the proper routing of the high cable (58), the low cable (23), the military press cable (72), and the leg press cable (99). Use the diagrams to be sure that the four cables and the cable traps have been assembled correctly. If the cables have ...

  • Page 27

    27 military press cable (72) leg press cable (99) rear weight stack— 1 2 3 4 5 3 2 4—rear seat frame 6—pivot arm 1—long “u”-bracket military press cable (72) and leg press cable (99).

  • Page 28: Ordering Replacement Parts

    Ordering replacement parts to order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to give the following information: 1. The model number of the product (wesy9635c.3) 2. The name of the product (weider pro 9635 weight system) 3. The serial number of ...

  • Page 30

    M8 x 63mm bolt (22) m6 x 63mm carriage bolt (92) m m8 x 67mm bolt (11) m8 x 70mm bolt (75) m8 x 74mm shoulder bolt (103) m8 x 70mm carriage bolt (14) m10 x 90mm bolt (16) m10 x 83mm bolt (67) m10 x 92mm bolt (88) m10 x 78mm bolt (105) m8 x 150mm bolt (60) m8 x 120mm bolt (68) m m6 x 63mm screw (43).

  • Page 31: Part Identification Chart

    M8 nylon locknut (3) m6 nylon locknut (2) m6 washer (10) m8 washer (8) m10 washer (9) m10 nylon locknut (21) m4 washer (76) m 1 0 x 1 9 6 m m b o lt (5 9 ) m4 x 16mm self-tapping screw (87) m8 x 45mm bolt (24) m8 x 57mm bolt (33) m6 x 50mm carriage bolt (38) m6 x 16mm screw (18) m6 x 50mm screw (81)...

  • Page 32

    8 1 save this part list/exploded drawing for future reference m.

  • Page 33

    Part list—model no. Wesy9635c.3 r0605b key no. Qty. Description 1 10 m8 x 62mm carriage bolt 2 2 m6 nylon locknut 3 38 m8 nylon locknut 4 1 base 5 1 stabilizer 6 1 25mm square inner cap 7 1 16mm x 14mm spacer 8 10 m8 washer 9 9 m10 washer 10 13 m6 washer 11 8 m8 x 67mm bolt 12 7 m10 x 47mm bolt 13 2...

  • Page 34: —

    6 0 2 7 2 1 1 5 5 5 1 2 1 1 8 1 5 1 2 4 4 8 8 1 5 5 8 2 1 4 4 2 1 3 6 1 6 2 2 4 3 5 8 7 1 3 6 5 6 3 6 4 2 5 2 6 1 9 2 1 9 3 3 4 9 6 2 2 4 6 4 6 6 7 3 9 1 5 2 1 5 9 2 3 2 1 1 7 2 7 1 4 1 0 4 3 4 1 4 2 2 1 3 5 0 3 1 8 6 7 0 6 9 6 9 7 0 2 1 4 7 4 4 4 5 4 4 4 5 4 8 5 0 3 1 8 6 1 3 4 0 3 8 3 7 1 8 3 2 3 ...