Xerox 4890 Advanced Quick Reference Card
Product range/positioning
The Xerox DocuPrint 4850/4890/92C NPS/IPS is a highlight color
printing system, fully compatible with the IBM AFP Group 3 page
printer with the Advanced Function Image and Graphics (AFIG) option.
The targeted impressions per month are as follows:
•
DocuPrint 4850 NPS/IPS: 100-750K
•
DocuPrint 4890/92C NPS/IPS: 250K-1.3 million
Usage outside this range may vary the service frequency.
Speed
Data can be printed at rates up to 92 pages per minute. Throughput
rate can vary depending upon job complexity and system configuration.
Resolution
DocuPrint 4850/4890 NPS/IPS: 300 by 300 spots per inch (spi)
DocuPrint 92C NPS/IPS: 600 by 600 spots per inch (spi)
Paper handling
•
20 lb. (80 gsm) bond to 110 lb. (200 gsm) index cut-sheet weights
•
Paper sizes: 8 by 10 in. (203 by 254 mm) to
8.5 by 14 in. (216 by 356 mm), including A4
Input:
•
Main Tray (Tray 1): 1000 sheet capacity of 20 lb. (80 gsm) bond
paper
•
Auxiliary Tray (Tray 2): 500 sheet capacity of 20 lb. (80 gsm) bond
paper
•
High Capacity Feeder (Optional): Two additional 1000 sheet
20 lb. (80 gsm) bond input feeders
Output:
•
Dual Stacker: Each tray holds 750 sheets of 20 lb. (80 gsm) bond
with offset capability
•
Sample Tray: 100 sheets of 20 lb. (80 gsm) bond
•
Stitcher/Stacker: 2000 sheets of 20 lb. (80 gsm) bond, up to 50
sheets stitched, offset capability. Capacity may vary depending
on the number of sheets stitched per set.
System control module
(High performance Sun workstation)
The NPS/IPS printing system comes with the Sun Blade 1000 or the
Sun Ultra 60 workstation.
Note: This configuration may change due to Xerox policy of staying
abreast of current technology.
•
Processor (system unit) containing:
•
Two UltraSPARC III 750 Mhz central processing unit (CPU)
modules (Sun Blade 1000) or 450 MHz CPU module (Sun
Ultra 60)
•
4 GB memory (four 1 GB DIMMs)
•
36 GB hard disk drive
•
DVD-ROM drive
•
3.5 inch diskette drive
•
Keyboard and mouse
•
18-inch monitor (Sun Blade 1000) or 21-inch moitor (Sun Ultra
60)
•
Optional Token Ring baord (Sun Blade 1000)
•
Two Printer Controller Interface (PCI) boards installed in the
processor to interface with the print engine. (Sun Blade 1000)
Printer module
•
No throughput degradation for highlight color printing
•
Simultaneous exposure of both black and color images for
excellent registration
•
Black dry ink (permanent) plus one color Customer Changeable
Unit (CCU) which will be either Red, Blue, Green, Cyan,
Magenta, Cardinal, Royal, Ruby, Violet, or Brown
•
Operator attention light
PSF environment
The system operates in the following PSF environments:
•
MVS
•
VM (channel-attached only)
•
VSE (channel-attached only)
•
OS/2
•
AS/400 (with TCP/IP only)
•
AIX
PDL compatibility
The system interprets the following text formats:
•
PostScript level 1
•
PostScript level 2
•
PCL5c
•
PCL5e
•
ASCII
Space requirements
Controller:
Note: The following is presented as an example of typical space
requirements for Sun workstations.
Space requirements for the printer controller are 36 by 36 inches/
91 by 91 cm.
•
Processor (Sun Blade 1000)
– 25 in. deep by 10 in. wide by 17.75 in. high
(63.5 cm by 25.4 cm by 45.1 cm)
•
Processor (Sun Ultra 60)
– 17.5 in. deep by 17.5 in. wide by 5 in. high
(44.5 cm by 44.5 cm by 12.7 cm)
•
Monitor (Sun Blade 1000)
– 10 in. deep by 17.5 in. wide by 18.5 in. high
(25.4 cm by 44.5 cm by 47 cm)
•
Monitor (Sun Ultra 60)
– 21 in. deep by 19 in. wide by 21 in. high
(53.3 cm by 48.3 cm by 53.3 cm)
•
4 mm DAT SCSI tape drive (optional)
– 12.25 in. deep by 7.5 in. wide by 2.75 in. high
(31 cm by 19 cm by 7 cm)
•
Keyboard
– 7.5 in. deep by 20 in. wide
(19.1 cm by 50.8 cm)
•
HCU (for a channel-attached system)
– 15 in. deep by 16 in. wide by 5 in. high
(40.8 cm by 41.6 cm by 12.6 cm)
•
Channel interface board and channel cable connector box (for
channel-attached systems)
– 9.7 in. deep by 27.1 in. wide
(24.6 cm by 68.8 cm)
Printer:
Space requirements (physical hardware and required service area)
for each of the printer configurations are:
•
DocuPrint 4850/4890/92C printer with dual stacker
– 164 in. by 106.5 in. (417 cm by 271 cm)
•
DocuPrint 4850/4890/92C printer with stitcher/stacker
– 162 in. by 106.5 in. (411 cm by 271 cm)
•
DocuPrint 4850/4890/92C printer with high-capacity feeder and
dual stacker
– 186 in. by 106.5 in. (473 cm by 271 cm)
•
DocuPrint 4850/4890/92C printer with high-capacity feeder and
stitcher/stacker
– 184 in. by 106.5 in. (467 cm by 271 cm)
Note: Additional space (6 in. by 64 in. / 15 cm by 163 cm) is required
in front of the printer for CCU cart operability.
For additional space/configuration options, refer to the Xerox DocuPrint
4850/4890/92C NPS/IPS Installation Planning Guide (Pub
#721P90090).
System connections
One of the following network communications systems may be used to
transport documents from the client workstation to the printer:
•
Ethernet LAN running TCP/IP, AppleTalk, or Novell NetWare
network protocol software.
•
Token Ring running TCP/IP or AppleTalk network protocol
software
•
Bus and tag channel connection, using the Host Channel Unit
(HCU) or the PCI board and control unit
•
Fibre Distributed Data Interface (FDDI) running TCP/IP, Novell
3.x, or AppleTalk network protocols (available only with the
Solaris 2.x environment). The FDDI supports a Single Connection
configuration only.
Note: DocuPrint does not support multiple network interfaces
simultaneously.