Xpresskit DBALL2-MRC01 User Manual - page 6
Page 6
Feature and Option List
To enter feature programming routine
Use the key to turn the ignition ON, then OFF.
Within 5 sec, press and HOLD the Programming button. The orange LED turns ON after 3 seconds. Release the Programming
button.
The green LED starts flashing slowly one time to indicate the feature number is 1. After a short delay, the red LED flashes rapidly
to indicate the current option of feature 1. It repeats until next action happens.
Changing feature options
Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature.
The red LED flashes rapidly the number of times equal to the current option number. After a short delay, the green LED flashes
slowly the number of times to indicate the current feature. It repeats until next action happens.
Accessing another feature
Press and release the Programming button a number of times to advance from the current feature to the next desired feature.
The green LED flashes slowly the number of times equal to the feature number. After a short delay, the red LED flashes rapidly to
indicate the current option of the current feature. It repeats until next action happens.
When the maximum number of feature or option is reached, the LED will starts flashing again from the first feature or option.
Once a feature is programmed
Another feature(s) can be programmed.
The feature programming can be exited.
Exiting feature programming
No activity for 30 seconds; after 30 seconds, the orange LED will turn ON for 2 seconds to confirm exiting.
OR
Press and HOLD the Programming button for 3 seconds. After 3 seconds, the orange LED will turn ON for 2 seconds to confirm
exiting.
Feature Programming
Programming
Button
Feat.
Operation
Flashes/Options
Description
1. No RF Output*
Module is connected to a remote starter using a standard installation.
2. SmartStart
Module is connected to SmartStart using an RSR or RXT installation (when available).
3. RFTD Output
Module is connected to an XL202 using an RSR or RXT installation (when available).
1. Driver Priority
2. Unlock All*
1. Disabled*
2. Enabled
1. OFF*
2. Windows Roll Up
3. Windows Roll Down
4. Gas Cap Open
1. OFF*
2. Windows Roll Up
3. Windows Roll Down
4. Gas Cap Open
1. OFF*
2. Windows Roll Up
3. Windows Roll Down
4. Gas Cap Open
RFTD Output Type
1
3
Comfort Closure
6
AUX 3
AUX 1
4
5
AUX 2
2
Unlock Driver
Priority
* Default Option
Rev.: 20150626
Platform: DBALL2
Firmware: MRC01
© 2014 Directed. All rights reserved.
&
Flashes
IGN
START
OFF
KEY
Key at IGN
IGN
START
OFF
KEY
Remove Key
Module reset will be done automatically upon programming.
2
When the LED turns ON orange release the IPB.
The LED turns ON red.
&
&
Solid Orange
Solid Red
Release
5
4
Turn the Ignition OFF
&
3 Sec
Off
Wait until the LED turns ON solid green for 3 seconds, then turns OFF.
The module has been successfully programmed.
Refer to the LED Diagnostics section on page 7 for more information and for troubleshooting purposes.
3
Turn the Ignition ON using Key or PTS
IGN
START
OFF
KEY
Remove Key
IGN
START
OFF
KEY
Key at IGN
&
Flashes
1
Connect the 10-pin & 12-pin harnesses to the module.
Press & hold the Integrated Programming button (IPB),
then connect the 4-pin D2D (only in D2D) & 14-pin harness
to the module (in D2D & W2W).
10-pin
D2D
st
1
th
5
12-pin
14-pin
nd
2
rd
3
th
4
Press Twice Push-to-Start (PTS) to turn the Ignition ON
START
STOP
START
STOP
E
E
N
N
GI
E
E
N
N
GI
x2
x1
or
or