Xpresskit DBALL2-MRC01 User Manual - page 7
Page 7
Flashes
Flashes
Flashes x4
Flashes x1
Flashes x5
Flashes x2
Flashes x3
Off
LED Diagnostics and Troubleshooting
LED
Status
Description
Troubleshooting
Solid red.
Waiting for the vehicle to be
started.
Solid red for 30 seconds,
then flashes once.
Solid red for 30 seconds,
then flashes twice.
FT CAN not detected.
HS CAN not detected.
The CAN wires may be incorrectly connected. Refer to
the wiring diagram to make the right connections.
The CAN wires may be incorrectly connected. Refer to
the wiring diagram to make the right connections.
Solid red for 30 seconds,
then flashes 3 times.
Invalid CAN network.
The CAN bus was detected but the ignition on CAN
message is not detected. Check if the firmware from
unit is correct.
Solid red for 30 seconds,
then flashes 4 times.
Invalid VIN.
The VIN number is invalid. Report the issue to technical
support.
Solid red for 30 seconds,
then flashes 5 times.
Internal error.
Report the issue to technical support.
Flashes green
continuously.
Flashes green
continuously.
Vehicle has been successfully
detected.
N/A.
Solid green for 3 seconds.
Module has been successfully
programmed.
N/A.
Ground out (GWR) is active.
N/A.
Off.
N/A.
Flashes green once.
Lock command has been
received.
Flashes green twice.
Unlock command has been
received.
Flashes green 3 times.
Trunk release command has
been received.
Flashes green 4 times.
Flashes green 5 times.
Aux 1 command has been
received.
Aux 2 command has been
received.
Solid x30 secs
Solid x30 secs
Flashes
x1
Flashes
x2
Solid x30 secs
Flashes
x3
Solid x30 secs
Flashes
x4
Solid x30 secs
Flashes
x5
Solid
x3
secs
Solid
Inactive Ground While Running
Active Ground While Running
Module Programming
If it does not flash, the bypass module did not receive the
signal. Verify the connections between the bypass and
the remote starter module.
If it does not flash, the bypass module did not receive the
signal. Verify the connections between the bypass and
the remote starter module.
If it does not flash, the bypass module did not receive the
signal. Verify the connections between the bypass and
the remote starter module.
If it does not flash, the bypass module did not receive the
signal. Verify the connections between the bypass and
the remote starter module.
If it does not flash, the bypass module did not receive the
signal. Verify the connections between the bypass and
the remote starter module.
The Ground While Running (status) wire is incorrectly
connected. Refer to the wiring diagram to make the right
connections.
Make sure that all the connections are correct (see
install sheet) and turn the ignition ON to begin the
programming sequence.
Rev.: 20150626
Platform: DBALL2
Firmware: MRC01
© 2014 Directed. All rights reserved.
&
Flashes
IGN
START
OFF
KEY
Key at IGN
IGN
START
OFF
KEY
Remove Key
Module reset will be done automatically upon programming.
2
When the LED turns ON orange release the IPB.
The LED turns ON red.
&
&
Solid Orange
Solid Red
Release
5
4
Turn the Ignition OFF
&
3 Sec
Off
Wait until the LED turns ON solid green for 3 seconds, then turns OFF.
The module has been successfully programmed.
Refer to the LED Diagnostics section on page 7 for more information and for troubleshooting purposes.
3
Turn the Ignition ON using Key or PTS
IGN
START
OFF
KEY
Remove Key
IGN
START
OFF
KEY
Key at IGN
&
Flashes
1
Connect the 10-pin & 12-pin harnesses to the module.
Press & hold the Integrated Programming button (IPB),
then connect the 4-pin D2D (only in D2D) & 14-pin harness
to the module (in D2D & W2W).
10-pin
D2D
st
1
th
5
12-pin
14-pin
nd
2
rd
3
th
4
Press Twice Push-to-Start (PTS) to turn the Ignition ON
START
STOP
START
STOP
E
E
N
N
GI
E
E
N
N
GI
x2
x1
or
or