Zektor MAS7.1 User Manual - Features
MAS7.1 Component Video Switch
7
MAS7.1 Component Video Switch
Features
Analog Audio
Channels:
Gain:
Signal to Noise:
Dynamic Range:
Audio Frequency Response:
Video Frequency Response:
Crosstalk:
Digital Video Channels
Protocols:
DVI / HDMI Bandwidth:
DVI/HDMI Pixel Rate:
HDTV Resolutions:
HDCP:
HDMI Audio:
PC Resolutions:
Digital Audio Channels
Inputs:
Outputs:
Maximum Transfer Rate:
Digital Audio Modes:
Coax Input Level Range:
Coax Output Level:
Control
IR Sensor:
IR Jack:
12V Control:
Serial Port:
Power Requirements:
Voltage Requirements:
Optional International:
Adapter Power Supply:
Dimensions:
Warranty:
Eight Full Bandwidth (200MHz) Channels
0 dB (Passive)
90dB re +4dBu, 22KHz BW, unweighted
112dB re +26dBu, 22KHz BW, unweighted
0Hz-100KHz, +0/-0.05 dB
Bandwidth: 0Hz-200MHz, +0/-3 dB
Greater than 100dB, 20Hz-20KHz, worst case all channels
DVI 1.0, HDMI 1.0 through HDMI 1.3a
Supports Deep Color 36-bit color depth and resolutions up to
1080p @ 60Hz or 720p/1080i @ 120Hz
2.25GHz
225Mps
480p through 1080p, including 720p and 1080i
(All Single Link DVI / HDMI modes are supported)
All DVI and HDMI HDCP modes are supported
Fully supports all HDMI Audio modes
640x480p through 1920x1200p
(All Single Link PC resolutions supported)
3 Coax, 3 Optical, (Auto conversion between formats)
1 Coax (S/PDIF), 1 Optical (TOSLINK), (Simultaneous)
Optical 13.2Mb/S, Coax 50Mb/S
PCM, DD5.1, DTS, All digital audio modes supported
200mV - 7.0V (S/PDIF compliant and PC Soundcard Compatible)
500mV Nominal (S/PDIF Compliant)
Modulation Frequency: 34KHz-42KHz
3V to 15V any polarity, modulated or unmodulated
3V to 15V (any polarity) for ON, less than 0.2V for OFF
(IR jack is opto-isolated to prevent ground loops)
9600 Baud (8N1), USB Serial Cable Compatible
K.I.S.S.™ Protocol, Firmware Upgradable
Standby 2W, On 4.5W Typical
90-120VAC, 60Hz
90-264VAC, 47-63Hz
Wall Mount, 9V @ 500ma, U.L. Listed (Center connection is '+')
Rack Mountable, 17”W x 6.5”D x 1.75”H
Two Year Parts and Labor
Specifications:
Specifications
Features of the MAS7.1:
Fully passive analog audio switching. All analog audio switching
is done using gold-clad over silver-paladium relay contacts. There
are no active components in the audio paths, no capacitors, no
resistors, just a gold on gold relay contact.
More than just an Analog Audio switch, the MAS7.1 will also
switch Digital Audio (with auto-conversions between Coax and Op-
tical inputs) and HDMI. Separate ground planes are used for the
analog and digital paths to help eliminate cross talk between the
analog and digital signals.
Use the MAS7.1 as a Multi-channel 7.1 audio switch, or at the
press of button it can become two independent switches, where
each switch can be easily configured to independently switch
Multi-channel 5.1 audio, Stereo Audio, Digital Audio, and HDMI,
channels. It's the ultimate in audio/video breakaway!
Independently adjustable delay times for each signal type.
Unmatched control features. The MAS7.1 can be controlled using
front panel buttons, an IR remote, an opto-isolated hardwired IR
jack that accepts modulated, or unmodulated IR signals of any
polarity, an RS-232 port, and even a simple 12V On/Off voltage.
It can be taught to use a different remote control, allowing you
to have an unlimited number of MAS7.1's in the same room and
control them all separately. The RS-232 command set is one of
the easiest to use on the market and allows unprecedented control
over the MAS7.1's operations.
Adjustable front panel LED intensities. Eliminate the distraction of
glaring LEDs by having the front panel dim after a few seconds of
sitting idle. The LEDs can even be dimmed to "off".
Perfect for the professional home theater installer! The MAS7.1 is
rack mountable and comes in black or silver.
•
•
•
•
•
•
•