1. DL manuals
  2. AAdynTech
  3. Lighting Equipment
  4. Punch Series Light
  5. User Manual

AAdynTech Punch Series Light User Manual - Table  Of  Contents

Manual is about: IP20 Protection

Summary of Punch Series Light

  • Page 1

    1 punch series light user manual (ip20 protection).

  • Page 2: Table  Of  Contents

    2 table of contents before you begin_________________________________________________ 3 what is included_________________________________________________ 3 unpacking instructions_____________________________________________3 symbol definitions________________________________________________ 3 safety...

  • Page 3: Before  You  Begin

    3 before you begin what is included • user’s manual • one (1) punch plus light • ac power input cable with plug o usa voltage (120vac), three-prong plug standard o 1- 120/240v adapter • diffuser lens, three (3), 15 o , 30 o and 55 o , 1 scrim bag and 1 doughnut frame • one (1) yoke pin with attachin...

  • Page 4

    4 • make sure that light is only used in dry location. Do not use light in or around falling water, wet locations or moisture. • always allow adequate ventilation of the light. Never cover or in any way obstruct the louvered openings in the light. • if light is suspended either from above or below u...

  • Page 5

    5 setup quick start remove the aadyn light from its protective shipping packaging and place it in a safe and secure location for setup or use. Prior to proceeding further, make sure that light is resting on a stable surface or is properly attached to a mounting location using the supplied yoke and y...

  • Page 6

    6 the 6’0” ac power cable for the punch series light is located in a plastic bag under the diffuser kit. • uncoil the black ac power cord from the holder and plug the blue female end into the ac input receptacle on the lower right portion of the housing..

  • Page 7

    7 • • plug the male end of the ac power cord into an appropriate ac power source. • turn on light by pressing the green power switch located in the upper right hand portion of the rear bulkhead, as shown above. • upon power up, the light will turn on immediately to its full brightness unless a speci...

  • Page 8

    8 control selection the light can be controlled via three means of interface as shown below: off cim/uim dmx (wired or wireless) cim/uim operation warning! Standard power cord supplied with punch light is intended to connect with standard, single-phase 110-120 vac, 60 hz usa circuit. Other power cor...

  • Page 9: 1. Functional Requirements

    9 1. Functional requirements the aadyn punch light is controlled by software (embedded firmware). In general the software shall control the light and accept user inputs from multiple device types. Via the user inputs the light may be controlled and various parameters may be saved in non-volatile mem...

  • Page 10

    10 • the software shall present individually sixteen startup profiles to the user: preset1, preset2, preset3, custom1 through custom12, and off changing the choice each time the right or left arrow button is pressed. • when a profile is selected by the user, the software shall save this choice to no...

  • Page 11

    11 • recall setting • the software shall present individually fifteen choices to the user: preset1, preset2, preset3, and custom1 through custom12 changing the choice each time a right or left arrow button is pressed. The custom settings are described below. • the preset settings shall be hard coded...

  • Page 12

    12 • 0 shall indicate that the uim brightness parameter change is to occur immediately and 100 percent shall introduce a three second delay in changing the current parameter value to the requested value. • at power on, the value of uim fade shall default to 0 percent if there is no power on profile....

  • Page 13

    13 • the factory default for the uim effect frequency parameter shall be 75%. • the preset values shall be set as follows: • preset 1 ! Light control = uim ! Uim brightness = 100% ! Uim fade = 0% ! Uim effect selection = none ! Uim effect frequency = 0% ! Dmx base address = 1 ! Dmx channel mode = 5 ...

  • Page 14

    14 the software shall retain the menu state after the uim is unplugged and remain on the same screen if the uim is reattached. 1.2. Douse switch/douse button • the software shall separately detect and process a press and release of the red cancel (x) button from the uim. On cancel button press, the ...

  • Page 15: General Specifications:

    15 general specifications:.

  • Page 16: Punch Plus

    16 punch plus.

  • Page 17: Punch Tungsten

    17 punch tungsten.

  • Page 18

    18 limited warranty aadyn technology, llc limited warranty aadyn technology, llc (“aadyntech”) products are covered by a limited warranty against manufacturing defects for two (2) years from the date of purchase by the original purchaser. Aadyntech’s liability is limited, at aadyntech’s option, to r...

  • Page 19

    19 general maintenance and care this light is intended for indoor use only. When not in use, the light should be stored in a generally dry and dust free area. General maintenance and care consists of making sure that the light always has good ventilation and that nothing is obstructing free air flow...