1. DL manuals
  2. ABB
  3. Relays
  4. rec670
  5. Product Manual

ABB rec670 Product Manual

Manual is about: Relion 670 Series, Bay Control

Summary of rec670

  • Page 1

    Relion ® 670 series transformer protection ret670 pre-configured product guide.

  • Page 2

    Contents 1. Application...........................................................3 2. Available functions...............................................8 4. Functionality.......................................................12 5. Hardware description.........................................27 6. C...

  • Page 3

    1. Application ret670 provides fast and selective protection, monitoring and control for two- and three-winding transformers, autotransformers, generator-transformer units and shunt reactors. The transformer ied is designed to operate correctly over a wide frequency range in order to accommodate pow...

  • Page 4

    Configuration tool ensures simple and fast testing and commissioning. Serial data communication is via optical connections to ensure immunity against disturbances. The wide application flexibility makes this product an excellent choice for both new installations and the refurbishment of existing ins...

  • Page 5

    In> 4 4 3u> 2 2 3u 2 2 i->o 51/67 51n/67n 59 27 94/86 87t 3id/i> idn/i> 87n idn/i> 87n 3i> 50bf 3i> 4 4 in> 4 4 51n/67n sc/vc 25 51/67 3i> 50bf 3i> 4 4 i->o 94/86 trip busbar trip busbar cb2 trip cb2 cb1 trip cb1 en05000272.Vsd iec05000272 v1 en figure 1. A typical protection application for a two w...

  • Page 6

    In> 4 4 3u> 2 2 3u 2 2 i->o 51/67 51n/67n 59 27 94/86 87t 3id/i> idn/i> 87n idn/i> 87n 3i> 50bf 3i> 4 4 in> 4 4 51n/67n sc/vc 25 51/67 3i> 50bf 3i> 4 4 i->o 94/86 trip busbar&cb2 trip busbar &cb1/2 cb3 trip cb3 cb1 trip cb1 cb2 s 3i> 50bf trip cb1/3 i->o 94/86 trip cb2 en05000273.Vsd iec05000273 v1 ...

  • Page 7

    In> 4 4 3u> 2 2 3u 2 2 i->o 51/67 51n/67n 59 27 94/86 87t 3id/i> idn/i> 87n idn/i> 87n 3i> 50bf 3i> 4 4 in> 4 4 51n/67n sc/ vc 25 51/67 3i> 50bf 3i> 4 4 i->o 94/86 trip busbar trip busbar &cb1/2/3 cb2 trip cb2 cb1 trip cb1 cb3 3i> 4 4 3i> 50bf trip busbar &cb1/2 un> 2 2 59n t2 trip i->o 94/86 en0500...

  • Page 8

    In> 4 4 3u> 2 2 3u 2 2 i->o 51/67 51n/67n 59 27 94/86 87t 3id/i> idn/i> 87n idn/i> 87n 3i> 50bf 3i> 4 4 in> 4 4 51n/67n sc/vc 25 51/67 3i> 50bf 3i> 4 4 i->o 94/86 trip busbar&cb2/3/4 trip busbar &cb1/2/4 cb3 trip cb3 cb1 trip cb1 cb2 s 3i> 50bf trip cb1/3/4/x i->o 94/86 trip cb2 cb4 3i> 4 4 3i> 50bf...

  • Page 9

    2. Available functions function description transformer back-up protection (a10) voltage control (a25) single breaker, 2 winding (a30) multi breaker, 2 winding (b30) single breaker, 3 winding (a40) multi breaker, 3 winding (b40) ansi basic option (qty/ option design) basic option (qty/ option design...

  • Page 10

    Function description transformer back-up protection (a10) voltage control (a25) single breaker, 2 winding (a30) multi breaker, 2 winding (b30) single breaker, 3 winding (a40) multi breaker, 3 winding (b40) ansi basic option (qty/ option design) basic option (qty/ option design) basic option (qty/ op...

  • Page 11

    Function description transformer back-up protection (a10) voltage control (a25) single breaker, 2 winding (a30) multi breaker, 2 winding (b30) single breaker, 3 winding (a40) multi breaker, 3 winding (b40) ansi basic option (qty/ option design) basic option (qty/ option design) basic option (qty/ op...

  • Page 12

    Function description transformer back-up protection (a10) voltage control (a25) single breaker, 2 winding (a30) multi breaker, 2 winding (b30) single breaker, 3 winding (a40) multi breaker, 3 winding (b40) ansi basic option (qty/ option design) basic option (qty/ option design) basic option (qty/ op...

  • Page 13

    Xx05000051.Vsd iec05000051 v1 en two-winding power transformer with two circuit breakers and two ct-sets on both sides three-winding applications xx05000052.Vsd iec05000052 v1 en three-winding power transformer with all three windings connected xx05000053.Vsd iec05000053 v1 en three-winding power tr...

  • Page 14

    Xx05000058.Vsd iec05000058 v1 en figure 6. Autotransformer low impedance ref impedance protection distance measuring zone, quadrilateral characteristic zmqpdis, zmqapdis the line distance protection is a four zone full scheme protection with three fault loops for phase-to-phase faults and three faul...

  • Page 15

    The distance protection zones can operate, independent of each other, in directional (forward or reverse) or non-directional mode. This makes them suitable, together with different communication schemes, for the protection of power lines and cables in complex network configurations, such as parallel...

  • Page 16

    With the reach limited to less than typical eighty percent of the transformer impedance at minimum source impedance. Efpioc can be configured to measure the residual current from the three-phase current inputs or the current from a separate current input. Efpioc can be blocked by activating the inpu...

  • Page 17

    Pole discordance protection ccrpld single pole operated circuit breakers can due to electrical or mechanical failures end up with the different poles in different positions (close-open). This can cause negative and zero sequence currents which gives thermal stress on rotating machines and can cause ...

  • Page 18

    Overexcitation protection oexpvph when the laminated core of a power transformer or generator is subjected to a magnetic flux density beyond its design limits, stray flux will flow into non-laminated components not designed to carry flux and cause eddy currents to flow. The eddy currents can cause e...

  • Page 19

    The general function suits applications with underimpedance and voltage controlled overcurrent solutions. The general function can also be utilized for generator transformer protection applications where positive, negative or zero sequence components of current and voltage quantities are typically r...

  • Page 20

    Evaluation of conditions from other functions such as interlocking, synchrocheck, operator place selection and external or internal blockings. Features in the apparatus control function: • select-execute principle to give high reliability • selection function to prevent simultaneous operation • sele...

  • Page 21

    Vsggio can be controlled from the menu or from a symbol on the single line diagram (sld) on the local hmi. Single point generic control 8 signals spc8ggio the single point generic control 8 signals (spc8ggio) function block is a collection of 8 single point commands, designed to bring in commands fr...

  • Page 22

    Sufficient length, as well as all functionality necessary for correct co-operation with autoreclosing functions. The trip function block includes functionality for evolving faults and breaker lock-out. Trip matrix logic tmaggio trip matrix logic (tmaggio) function is used to route trip signals and/o...

  • Page 23

    Supervision of ma input signals (mvggio) the main purpose of the function is to measure and process signals from different measuring transducers. Many devices used in process control represent various parameters such as frequency, temperature and dc battery voltage as low current values, usually in ...

  • Page 24

    The event recorder logs all selected binary input signals connected to the disturbance report function. Each recording can contain up to 150 time-tagged events. The event recorder information is available for the disturbances locally in the ied. The event recording information is an integrated part ...

  • Page 25

    By the binary input module and then read by the pulse counter function. A scaled service value is available over the station bus. The special binary input module with enhanced pulse counting capabilities must be ordered to achieve this functionality. Function for energy calculation and demand handli...

  • Page 26

    61850-8-1 protocol allows intelligent devices (ieds) from different vendors to exchange information and simplifies system engineering. Peer-to-peer communication according to goose is part of the standard. Disturbance files uploading is provided. Serial communication, lon existing stations with abb ...

  • Page 27

    Kbit/s resp 2mbit/s operation. The converter is delivered with 19” rack mounting accessories. 5. Hardware description hardware modules power supply module psm the power supply module is used to provide the correct internal voltages and full isolation between the terminal and the battery system. An i...

  • Page 28

    Galvanic rs485 serial communication module the galvanic rs485 serial communication module is used as an alternative for dnp3.0 communication. Gps time synchronization module gsm this module includes the gps receiver used for time synchronization. The gps has one sma contact for connection to an ante...

  • Page 29

    Xx05000004.Vsd iec05000004 v1 en figure 9. Side-by-side mounting case size a b c d e f 6u, 1/2 x 19” 265.9 223.7 201.1 242.1 252.9 205.7 6u, 3/4 x 19” 265.9 336.0 201.1 242.1 252.9 318.0 6u, 1/1 x 19” 265.9 448.1 201.1 242.1 252.9 430.3 (mm) mounting alternatives following mounting alternatives (ip4...

  • Page 30

    6. Connection diagrams table 1. Designations for 1/2 x 19” casing with 1 trm slot iec08000471 bg v1 en module rear positions psm x11 bim, bom, som or iom x31 and x32 etc. To x51 and x52 bim, bom, som, iom or gsm x51, x52 slm x301:a, b, c, d irig-b 1) x302 oem x311:a, b, c, d rs485 or ldcm 2) 3) x312...

  • Page 31

    Table 2. Designations for 3/4 x 19” casing with 2 trm slot iec08000473 bg v1 en module rear positions psm x11 bim, bom, som, iom or mim x31 and x32 etc. To x71 and x72 bim, bom, som, iom, mim or gsm x71, x72 slm x301:a, b, c, d irig-b or ldcm 1,2) x302 ldcm 2) x303 oem 4) x311:a, b, c, d rs485 or ld...

  • Page 32

    Table 3. Designations for 1/1 x 19” casing with 2 trm slots iec08000475 bg v1 en module rear positions psm x11 bim, bom, som, iom or mim x31 and x32 etc. To x131 and x132 bim, bom, som, iom, mim or gsm x131, x132 slm x301:a, b, c, d irig-b or ldcm 1,2) x302 ldcm 2) x303 oem 4) x311:a, b, c, d rs485 ...

  • Page 33

    Iec08000479 bg v1 en figure 10. Transformer input module (trm) ￭ indicates high polarity ct/vt-input designation according to figure 10 current/voltage configuration (50/60 hz) ai01 ai02 ai03 ai04 ai05 ai06 ai07 ai08 ai09 ai10 ai11 ai12 12i, 1a 1a 1a 1a 1a 1a 1a 1a 1a 1a 1a 1a 1a 12i, 5a 5a 5a 5a 5a...

  • Page 34

    Iec08000480 bg v1 en figure 11. Binary input module (bim). Input contacts named xa corresponds to rear position x31, x41, and so on, and input contacts named xb to rear position x32, x42, and so on. Iec08000484 bg v1 en figure 12. Ma input module (mim) transformer protection ret670 1mrk 504 091-ben ...

  • Page 35

    Iec08000477 bg v1 en figure 13. Communication interfaces (oem, ldcm, slm and hmi) note to figure 13 1) rear communication port spa/iec 61850-5-103, st-connector for glass alt. Hfbr snap-in connector for plastic as ordered 2) rear communication port lon, st connector for glass alt. Hfbr snap-in conne...

  • Page 36

    Iec08000478 bg v1 en figure 15. Gps time synchronization module (gsm) iec08000481 bg v1 en figure 16. Binary output module (bom). Output contacts named xa corresponds to rear position x31, x41, and so on, and output contacts named xb to rear position x32, x42, and so on. Transformer protection ret67...

  • Page 37

    Iec08000482 bg v1 en figure 17. Static output module (som) iec08000483 bg v1 en figure 18. Binary in/out module (iom). Input contacts named xa corresponds to rear position x31, x41, and so on, and output contacts named xb to rear position x32, x42, and so on. Transformer protection ret670 1mrk 504 0...

  • Page 38

    C c t c t c p1 -qb1 -qb2 -qa1 -bi1 qb1-open qb1-cl qb2-open qb2-cl qa1-open qa1-cl qa1-spr unch close qa1 trip qa1 main 2 trip bus a bus b qa1-open qa1-cl bbp-trip st bfp 3ph buch trip sudden p man sc ok f a u lt s ig n a ll in g to main 2 relay to bus prot mcb or fuse mcb-ok - + irf wt warn hv busb...

  • Page 39

    C c t c t c p1 -qb1 -qb62 -qa1 -bi1 qb1-open qb1-cl qb6-open qb6-cl =1-qa1-open =1-qa1-cl =1-qa1-spr unch close qa1 trip qa1 main 2 trip bus a qa1-open qa1-cl bbp-trip st bfp 3ph buch trip sudden p man sc ok f a u lt s ig n a ll in g to main 2 to bb prot mcb or fuse mcb-ok - + irf wt warn hv busbar ...

  • Page 40

    C c t c t c p1 -qb1 -qb2 -qa1 -bi1 qb1-cl qb2-cl qa1-open qa1-cl qa1-spr unch close qa1 trip qa1 main 2 trip bus a bus b qa1-open qa1-cl bbp-trip st bfp 3ph buch trip sudden p man sc ok f a u lt s ig n a ll in g to main 2 relay to bus prot mcb or fuse mcb-ok - + irf wt warn hv busbar trip trip reinf...

  • Page 41

    C c t c t c p1 -qb1 -qb62 -qa1 -bi1 qb1-open qb1-cl qb62-open qb62-cl =1-q0-open =1-q0-cl =1-q0-spr unch close qa1 trip qa1 main 2 trip bus a qa1-open qa1-cl bbp-trip st bfp 3ph buch trip sudden p man sc ok f a u lt s ig n a ll in g to main 2 to bb prot mcb or fuse mcb-ok - + irf wt warn hv busbar t...

  • Page 42

    7. Technical data general definitions reference value the specified value of an influencing factor to which are referred the characteristics of the equipment nominal range the range of values of an influencing quantity (factor) within which, under specified conditions, the equipment meets the specif...

  • Page 43

    Table 5. Mim - ma input module quantity: rated value: nominal range: input resistance r in = 194 ohm - input range ± 5, ± 10, ± 20ma 0-5, 0-10, 0-20, 4-20ma - power consumption each ma-board each ma input £ 4 w £ 0.1 w - table 6. Oem - optical ethernet module quantity rated value number of channels ...

  • Page 44

    Binary inputs and outputs table 8. Bim - binary input module quantity rated value nominal range binary inputs 16 - dc voltage, rl 24/40 v 48/60 v 110/125 v 220/250 v rl ± 20% rl ± 20% rl ± 20% rl ± 20% power consumption 24/40 v 48/60 v 110/125 v 220/250 v max. 0.05 w/input max. 0.1 w/input max. 0.2 ...

  • Page 45

    Table 10. Iom - binary input/output module quantity rated value nominal range binary inputs 8 - dc voltage, rl 24/40 v 48/60 v 110/125 v 220/250 v rl ± 20% rl ± 20% rl ± 20% rl ± 20% power consumption 24/40 v 48/60 v 110/125 v 220/250 v max. 0.05 w/input max. 0.1 w/input max. 0.2 w/input max. 0.4 w/...

  • Page 46

    Table 12. Som - static output module (reference standard: iec 61810-2): static binary outputs function of quantity static binary output trip rated voltage 48 - 60 vdc 110 - 250 vdc number of outputs 6 6 impedance open state ~300 kΩ ~810 kΩ test voltage across open contact, 1 min no galvanic separati...

  • Page 47

    Table 13. Som - static output module data (reference standard: iec 61810-2): electromechanical relay outputs function of quantity trip and signal relays max system voltage 250v ac/dc number of outputs 6 test voltage across open contact, 1 min 1000v rms current carrying capacity: continuous 8a 1.0s 1...

  • Page 48

    Influencing factors table 15. Temperature and humidity influence parameter reference value nominal range influence ambient temperature, operate value +20 °c -10 °c to +55 °c 0.02% /°c relative humidity operative range 10%-90% 0%-95% 10%-90% - storage temperature -40 °c to +70 °c - - table 16. Auxili...

  • Page 49

    Type tests according to standards table 18. Electromagnetic compatibility test type test values reference standards 1 mhz burst disturbance 2.5 kv iec 60255-22-1, class iii ring wave immunity test 2-4 kv iec 61000-4-12, class iii surge withstand capability test 2.5 kv, oscillatory 4.0 kv, fast trans...

  • Page 50

    Table 19. Insulation test type test values reference standard dielectric test 2.0 kv ac, 1 min. Iec 60255-5 impulse voltage test 5 kv, 1.2/50 m s, 0.5 j insulation resistance >100 m w at 500 vdc table 20. Environmental tests test type test value reference standard cold test test ad for 16 h at -25°c...

  • Page 51

    Differential protection table 23. Transformer differential protection t2wpdif, t3wpdif function range or value accuracy operating characteristic adaptable ± 2.0% of ir for i ± 2.0% of ir for i > ir reset ratio > 95% - unrestrained differential current limit (100-5000)% of ibase on high voltage windi...

  • Page 52

    Table 24. Restricted earth fault protection, low impedance refpdif function range or value accuracy operate characteristic adaptable ± 2.0% of ir r for i ± 2.0% of i for i > irbase reset ratio >95% - base sensitivity function (4.0-100.0)% of ibase ± 2.0% of i r directional characteristic fixed 180 d...

  • Page 53

    Impedance protection table 26. Distance measuring zone, quad zmqpdis function range or value accuracy number of zones 4 with selectable direction - minimum operate residual current, zone 1 (5-30)% of ibase - minimum operate current, phase-to-phase and phase- to-earth (10-30)% of ibase - positive seq...

  • Page 54

    Table 27. Full-scheme distance protection, mho characteristic zmhpdis function range or value accuracy number of zones with selectable directions 4 with selectable direction - minimum operate current (10–30)% of i base - positive sequence impedance, phase-to- earth loop (0.005–3000.000) w / phase ± ...

  • Page 55

    Table 28. Full-scheme distance protection, quadrilateral for earth faults zmmpdis function range or value accuracy number of zones 4 with selectable direction - minimum operate current (10-30)% of ibase - positive sequence reactance (0.50-3000.00) w /phase ± 2.0% static accuracy ± 2.0 degrees static...

  • Page 56

    Table 29. Phase selection with load encroachment, quadrilateral characteristic function range or value accuracy minimum operate current (5-30)% of ibase ± 1.0% of ibase reactive reach, positive sequence , forward and reverse (0.50–3000.00) Ω/phase ± 2.0% static accuracy ± 2.0 degrees static angular ...

  • Page 57

    Table 31. Power swing detection zmrpsb function range or value accuracy reactive reach (0.10-3000.00) w /phase ± 2.0% static accuracy conditions: voltage range: (0.1-1.1) x u r current range: (0.5-30) x i r angle: at 0 degrees and 85 degrees resistive reach (0.10–1000.00) w /loop timers (0.000-60.00...

  • Page 58

    Table 33. Four step phase overcurrent protection oc4ptoc function setting range accuracy operate current (1-2500)% of lbase ± 1.0% of i r at i £ i r ± 1.0% of i at i > i r reset ratio > 95% - min. Operating current (1-100)% of lbase ± 1.0% of i r relay characteristic angle (rca) (-70.0– -50.0) degre...

  • Page 59

    Table 34. Instantaneous residual overcurrent protection efpioc function range or value accuracy operate current (1-2500)% of lbase ± 1.0% of i r at i £ i r ± 1.0% of i at i > i r reset ratio > 95% - operate time 25 ms typically at 0 to 2 x i set - reset time 25 ms typically at 2 to 0 x i set - criti...

  • Page 60

    Table 35. Four step residual overcurrent protection ef4ptoc function range or value accuracy operate current (1-2500)% of lbase ± 1.0% of i r at i £ i r ± 1.0% of i at i > i r reset ratio > 95% - operate current for directional comparison (1–100)% of lbase ± 1.0% of i r timers (0.000-60.000) s ± 0.5...

  • Page 61

    Table 36. Sensitive directional residual overcurrent and power protection sdepsde function range or value accuracy operate level for 3i 0 ·cos j directional residual overcurrent (0.25-200.00)% of lbase at low setting: (2.5-10) ma (10-50) ma ± 1.0% of i r at i £ i r ± 1.0% of i at i > i r ± 1.0 ma ± ...

  • Page 62

    Table 36. Sensitive directional residual overcurrent and power protection sdepsde , continued function range or value accuracy operate time, non directional residual over current 60 ms typically at 0 to 2 x i set - reset time, non directional residual over current 60 ms typically at 2 to 0 x i set -...

  • Page 63

    Table 38. Breaker failure protection ccrbrf function range or value accuracy operate phase current (5-200)% of lbase ± 1.0% of i r at i £ i r ± 1.0% of i at i > i r reset ratio, phase current > 95% - operate residual current (2-200)% of lbase ± 1.0% of i r at i £ i r ± 1.0% of i at i > i r reset rat...

  • Page 64

    Table 41. Directional overpower protection goppdop function range or value accuracy power level (0.0–500.0)% of s base at low setting: (0.5-2.0)% of s base (2.0-10)% of s base ± 1.0% of s r at s r ± 1.0% of s at s > s r ± 50% of set value ± 20% of set value characteristic angle (-180.0–180.0) degree...

  • Page 65

    Table 44. Two step overvoltage protection ov2ptov function range or value accuracy operate voltage, low and high step (1-200)% of ubase ± 1.0% of u r at u r ± 1.0% of u at u > u r absolute hysteresis (0–100)% of u base ± 1.0% of u r at u r ± 1.0% of u at u > u r inverse time characteristics for low ...

  • Page 66

    Table 46. Overexcitation protection oexpvph function range or value accuracy operate value, start (100–180)% of (ubase/f rated ) ± 1.0% of u operate value, alarm (50–120)% of start level ± 1.0% of u r at u ≤ u r ± 1.0% of u at u > u r operate value, high level (100–200)% of (ubase/f rated ) ± 1.0% o...

  • Page 67

    Frequency protection table 48. Underfrequency protection saptuf function range or value accuracy operate value, start function (35.00-75.00) hz ± 2.0 mhz operate time, start function 100 ms typically - reset time, start function 100 ms typically - operate time, definite time function (0.000-60.000)s...

  • Page 68

    Multipurpose protection table 51. General current and voltage protection (gapc) function range or value accuracy measuring current input phase1, phase2, phase3, posseq, negseq, 3*zeroseq, maxph, minph, unbalanceph, phase1-phase2, phase2-phase3, phase3-phase1, maxph-ph, minph-ph, unbalanceph-ph - bas...

  • Page 69

    Table 51. General current and voltage protection (gapc), continued function range or value accuracy voltage level where voltage memory takes over (0.0 - 5.0)% of u base ± 1.0% of u r start overvoltage, step 1 and 2 (2.0 - 200.0)% of u base ± 1.0% of u r for u r ± 1.0% of u for u>u r start undervolta...

  • Page 70

    Table 51. General current and voltage protection (gapc), continued function range or value accuracy undervoltage: critical impulse time 10 ms typically at 2 to 0 x u set - impulse margin time 15 ms typically - secondary system supervision table 52. Current circuit supervision ccsrdif function range ...

  • Page 71

    Control table 54. Synchronizing, synchrocheck and energizing check sesrsyn function range or value accuracy phase shift, j line - j bus (-180 to 180) degrees - voltage ratio, u bus /u line (0.40-25.000) % of ubase - voltage high limit for synchronizing and synchrocheck (50.0-120.0)% of ubase ± 1.0% ...

  • Page 72

    Table 55. Voltage control tr1atcc, tr8atcc, tcmyltc and tlcyltc function range or value accuracy transformer reactance (0.1–200.0)Ω, primary - time delay for lower command when fast step down mode is activated (1.0–100.0) s - voltage control set voltage (85.0–120.0)% of ub ±0.25% of u r outer voltag...

  • Page 73

    Table 55. Voltage control tr1atcc, tr8atcc, tcmyltc and tlcyltc, continued function range or value accuracy alarm level of active power in forward and reverse direction (-9999.99–9999.99) mw ± 1.0% of s r alarm level of reactive power in forward and reverse direction (-9999.99–9999.99) mvar ± 1.0% o...

  • Page 74

    Table 57. Current reversal and weak-end infeed logic for residual overcurrent protection ecrwpsch function range or value accuracy operating mode of wei logic off echo echo & trip - operate voltage 3u o for wei trip (5-70)% of ubase ± 1.0% of u r reset ratio >95% - operate time for current reversal ...

  • Page 75

    Table 59. Configurable logic blocks logic block quantity with cycle time range or value accuracy fast medium normal logicand 60 60 160 - - logicor 60 60 160 - - logicxor 10 10 20 - - logicinverter 30 30 80 - - logicsrmemory 10 10 20 - - logicgate 10 10 20 - - logictimer 10 10 20 (0.000–90000.000) s ...

  • Page 76

    Table 61. Supervision of ma input signals (mvggio) function range or value accuracy ma measuring function ± 5, ± 10, ± 20 ma 0-5, 0-10, 0-20, 4-20 ma ± 0.1 % of set value ± 0.005 ma max current of transducer to input (-20.00 to +20.00) ma min current of transducer to input (-20.00 to +20.00) ma alar...

  • Page 77

    Table 63. Disturbance report drprdre function range or value accuracy pre-fault time (0.05–1.00) s - post-fault time (0.1–10.0) s - limit time (0.5–10.0) s - maximum number of recordings 100 - time tagging resolution 1 ms see table 85 maximum number of analog inputs 30 + 10 (external + internally de...

  • Page 78

    Table 65. Indications function value buffer capacity maximum number of indications presented for single disturbance 96 maximum number of recorded disturbances 100 table 66. Event recorder function value buffer capacity maximum number of events in disturbance report 150 maximum number of disturbance ...

  • Page 79

    Table 70. Energy metering etpmmtr function range or value accuracy energy metering kwh export/import, kvarh export/import input from mmxu. No extra error at steady load station communication table 71. Iec 61850-8-1 communication protocol function value protocol iec 61850-8-1 communication speed for ...

  • Page 80

    Table 75. Slm – lon port quantity range or value optical connector glass fibre: type st plastic fibre: type hfbr snap-in fibre, optical budget glass fibre: 11 db (1000 m typically *) plastic fibre: 7 db (10 m typically *) fibre diameter glass fibre: 62.5/125 m m plastic fibre: 1 mm *) depending on o...

  • Page 81

    Table 78. Line data communication module characteristic range or value type of ldcm short range (sr) medium range (mr) long range (lr) type of fibre graded-index multimode 62.5/125 µm or 50/125 µm singlemode 9/125 µm singlemode 9/125 µm wave length 850 nm 1310 nm 1550 nm optical budget graded-index ...

  • Page 82

    Ied table 79. Case material steel sheet front plate steel sheet profile with cut-out for hmi surface treatment aluzink preplated steel finish light grey (ral 7035) table 80. Water and dust protection level according to iec 60529 front ip40 (ip54 with sealing strip) rear, sides, top and bottom ip20 t...

  • Page 83

    Basic ied functions table 84. Self supervision with internal event list data value recording manner continuous, event controlled list size 1000 events, first in-first out table 85. Time synchronization, time tagging function value time tagging resolution, events and sampled measurement values 1 ms t...

  • Page 84

    Table 88. Irig-b quantity rated value number of channels irig-b 1 number of channels pps 1 electrical connector irig-b bnc optical connector pps and irig-b type st type of fibre 62.5/125 μm multimode fibre inverse characteristic table 89. Ansi inverse time characteristics function range or value acc...

  • Page 85

    Table 90. Iec inverse time characteristics function range or value accuracy operating characteristic: ( ) 1 = × - æ ö ç ÷ ç ÷ è ø p a t k i equation1251-small v1 en i = i measured /i set k = (0.05-999) in steps of 0.01 - time delay to reset, iec inverse time (0.000-60.000) s ± 0.5% of set time ± 10 ...

  • Page 86

    Table 91. Ri and rd type inverse time characteristics function range or value accuracy ri type inverse characteristic 1 0.236 0.339 = × - t k i equation1137-small v1 en i = i measured /i set k = (0.05-999) in steps of 0.01 iec 60255-3, class 5 + 40 ms rd type logarithmic inverse characteristic 5.8 1...

  • Page 87

    Table 92. Inverse time characteristics for two step undervoltage protection (puvm, 27) function range or value accuracy type a curve: = æ ö ç ÷ è ø k t u u u equation1431-small v1 en (equation 4) u set u = uv measured k = (0.05-1.10) in steps of 0.01 class 5 +40 ms type b curve: 2.0 480 0.055 32 0.5...

  • Page 88

    Table 93. Inverse time characteristics for two step overvoltage protection (povm, 59) function range or value accuracy type a curve: = - > > æ ö ç ÷ è ø t k u u u equation1436-small v1 en (equation 7) u> = u set u = u measured k = (0.05-1.10) in steps of 0.01 class 5 +40 ms type b curve: 2.0 480 32 ...

  • Page 89

    Table 94. Inverse time characteristics for two step residual overvoltage protection (povm, 59n) function range or value accuracy type a curve: = - > > æ ö ç ÷ è ø t k u u u equation1436-small v1 en (equation 11) u> = u set u = u measured k = (0.05-1.10) in steps of 0.01 class 5 +40 ms type b curve: ...

  • Page 90

    8. Ordering guidelines carefully read and follow the set of rules to ensure problem-free order management. Please refer to the available functions table for included application functions. To obtain the complete ordering code, please combine code from the tables, as given in the example below. Exemp...

  • Page 91

    Software options #3 notes and rules no option x00 all fields in the ordering form do not need to be filled in restricted earth fault protection, low impedance a01 note: a01 only for a40/b40 high impedance differential protection - 3 blocks a02 note: a02, b02, b08, c05, c17, f02, h09, h11, h15 not in...

  • Page 92

    First hmi language #4 notes and rules english iec b1 english us b2 additional hmi language no second hmi language x0 german a1 russian a2 french a3 spanish a4 italian a5 polish a6 hungarian a7 czech a8 swedish a9 selection for position #4. Casing #5 notes and rules 1/2 x 19" case a note: only for a1...

  • Page 93

    Connection type for analog modules #9 notes and rules compression terminals a ringlug terminals b analog system first trm, 9i+3u 1a, 110/220v 3 note: not in a25 first trm, 9i+3u 5a, 110/220v 4 note: not in a25 first trm, 5i, 1a+4i, 5a+3u, 110/220v 5 note: not in a25 first trm, 6i+6u 1a, 100/220v 6 n...

  • Page 94

    Binary input/output module, ma and time synchronizating boards. Note: 1bim and 1 bom included in a31/a32/b31/b32, 1 iom basic in a21. #10 notes and rules slot position (rear view) x31 x41 x51 x61 x71 x81 x91 x101 x111 x121 x131 1/2 case with 1 trm note: only for a10/a25/a30 3/4 case with 2 trm 1/1 c...

  • Page 95

    Remote end communication, dnp serial comm. And time synchronization modules #11 notes and rules slot position (rear view) x312 x313 x302 x303 x322 x323 available slots in 1/2 case with 1trm note: only 1 ldcm. Only for a30 available slots in 3/4 & 1/1 case with 2 trm note: max 2 ldcm. Only for a25 no...

  • Page 96

    Basic ied functions self-supervision with internal event list time and synchronization error time synchronization parameter setting groups test mode functionality change lock function ied identifiers product information misc base common ied runtime comp rated system frequency signal matrix for binar...

  • Page 97

    Interface converter (for remote end data communication) external interface converter from c37.94 to g703 including 1u 19” rack mounting accessories quantity: 1mrk 002 245-aa external interface converter from c37.94 to g703.E1 quantity: 1mrk 002 245-ba test switch the test system combitest intended f...

  • Page 98

    External resistor unit for high impedance differential protection high impedance resistor unit 1-ph with resistor 1.8 kohms and voltage dependent resistor for 20-100v operating voltage quantity: 1 2 3 rk795101-ma high impedance resistor unit 3-ph with resistor 1.8 kohms and voltage dependent resisto...

  • Page 99

    User documentation rule: specify the number of printed manuals requested operator’s manual iec quantity: 1mrk 504 087-uen ansi quantity: 1mrk 504 087-uus technical reference manual iec quantity: 1mrk 504 086-uen ansi quantity: 1mrk 504 086-uus installation and commissioning manual iec quantity: 1mrk...

  • Page 100

    Related documents documents related to ret670 identity number operator’s manual 1mrk 504 087-uen installation and commissioning manual 1mrk 504 088-uen technical reference manual 1mrk 504 086-uen application manual 1mrk 504 089-uen buyer’s guide 1mrk 504 091-ben sample specification sa2005-001283 co...

  • Page 101

    101.

  • Page 102

    Contact us abb ab substation automation products se-721 59 västerås, sweden phone +46 (0) 21 32 50 00 fax +46 (0) 21 14 69 18 www.Abb.Com/substationautomation 1mrk 504 091-ben b © copyright 2010 abb. All rights reserved..