Abrelex EnerSolis ES 10000 User Manual - page 21
40
Table 3. Grid fault alarm codes and descriptions
LCD
Designation
Description
Repair
AL00
Utility over-voltage
The utility voltage is
greater than or less than
the permissible values.
1. Wait for 1 minute. If the grid returns
to normal then the inverter
automatically restarts.
2. Check the grid connection, such as
wires and connectors.
3. Make sure the grid voltage and
frequency meet the specifications.
4. If the error code keeps recurring
contact your local distributor for help.
AL01
Utility under-voltage
AL02
Utility
over-frequency
The utility frequency is
greater than or less than
the permissible values.
AL03
Utility
under-frequency
AL04
BOOSTER_A input
over-voltage
Over or under voltage at
DC input
1. Disconnect ALL PV (+) and PV (-)
cables.
2. Ensure that the open PV voltage is
outside the 300-1000 VDC range.
3. If PV voltage is normal and the
problem still occurs contact your local
distributor for help.
AL05
BOOSTER_A input
under-voltage
AL06
BOOSTER_B input
over-voltage
AL07
BOOSTER_B input
under-voltage
AL08
Anti-islanding
No utility, or utility failure
1. Disconnect ALL PV (+) and PV (-)
cables.
2. Check the grid connection, such as
wires and connectors.
3. Check for grid usability.
4. If the utility is normal and the error
code keeps recurring contact your
local distributor for help.
AL 13
Utility phase failure
AL10
GFDI
Leakage current on the
ground conductor is too
high.
1. Unplug the PV generator from the
input. Check the AC peripheral
system.
2. After the problem is cleared re-plug
the PV generator. Check the PV
inverter status.
3. If the error code keeps recurring
contact your local distributor for help.
AL11
Isolation fault
The impedance between
PV (+) and PV(-) and
ground is less than 1
M
Ω
.
1. Disconnect ALL PV (+) and PV (-)
cables.
2. Check the impedance between PV
(+) and PV (-) and ground. The
impedance must be greater than 2
M
Ω
.
3. If the error code keeps recurring
contact your local distributor for help.
AL23
PV Inverter is under
initialization
PV Inverter is under
initialization
N/A
41
10 Specifications
Model
Item
ES 6000
ES 8000
ES 10000
ES 12000
Inverter
Technology
Conversion
Mode
Sine-wave, Current source, High-frequency PWM
Isolation
Method
Transformer-less Design
DC Input Data
Nominal DC Voltage
620 VDC
Max. DC Input Voltage
1,000 VDC
MPP Voltage Range
300 ~ 1,000 VDC
Max. DC Input current
2 × 8.5 Amp
2 × 11.4 Amp
2 × 14.3 Amp
2 × 14.3 Amp
MPP Tracker
2
Isc
35A
AC Output Data
Nominal AC Power
6,000 Watt
8,000 Watt
10,000 Watt
12,000 Watt
Max. AC Apparent Power
6,600 VA
8,800 VA
11,000 VA
12,000 VA
Nominal AC Voltage
AC 230V × 3
Output Connect Method
3-Phase / 4-Wires (L1, L2, L3, N, PE)
AC Voltage Rang
184V ~ 264.5V (Base on 230 Vac)
Nominal AC Current
8.69 Amp × 3
11.59 Amp × 3
14.49 Amp × 3
17.39 Amp × 3
Frequency
50 / 60Hz Auto-Selection
(45.0 ~ 55.0Hz or 57.0 ~ 63.0Hz)
Power Factor
Leading 0.9 ~ Lagging 0.9
Current Distortion
Total Harmonic Current : Less than 5%
Single Harmonic Current : Less than 3%
Efficiency Data
Max. Efficiency
97.60%
Euro Efficiency
96.20%
96.60%
97.00%
97.25%
Environmental
Operating Temperature
-20 °C to +60 °C
-4 °F to 139°F
Pollution degree
PD3
Overvoltage
category
(IEC 60664-1)
DC side
Category Ⅱ
AC side
Category Ⅲ
Humidity
0 to 100% (Without condensation)
Altitude
0-2,000 m / 0-6,600 ft
Mechanical
Dimensions
(W x H x D in mm / in)
451 × 595 × 247 / 17.7 × 23.4 × 9.72
Net Weight (kg / lbs)
41 / 90.4
Gross Weight (kg / lbs)
44 / 97.0
Protection Class
IP65, outdoor
Cooling
Temperature-dependent fan
AC connector
Connector