- DL manuals
- ABS
- Lifting Systems
- Sanimat 1501S
- Installation And Operating Instructions Manual
ABS Sanimat 1501S Installation And Operating Instructions Manual
Summary of Sanimat 1501S
Page 1
Www.Absgroup.Com abs lifting station sanimat 1030-00 15970299gb (10/2006) installation and operating instructions gb.
Page 2
abs lifting station sanimat abs reserves the right to alter specifications due to technical developments c 1 g ...................................................................................................
Page 3
3 abs lifting station sanimat 1 g 1.1 a m these lifting stations may not be used for the collection or pumping of flammable or corrosive liquids. Effluent containing grease, petrol, or oil should only be brought to the lifting station via a...
Page 4
4 abs lifting station sanimat 1.4 d f h f f 1031-00 figure 2 design of the lifting station discharge line shut-off valve ball-type non-return valve inflow port dn 150/200, height 600 mm motor connection cable submersible pump pump head s...
Page 5
5 abs lifting station sanimat 1.5 d the flood-proof sewage lifting station sanimat 1501s to 3702s are made up of a gas and odour-tight synthetic collection tank complying with din 19760 and 12050-1 with either 1 or 2 submersible sewage pumps, together...
Page 6
6 abs lifting station sanimat 4 m note werecommendthatoriginalabsinstallationaccessoriesbeusedformountingand installationoftheunit m particular attention must be paid to the safety regulations covering work in closed areas as well as goo...
Page 7
abs lifting station sanimat 4.1 s q m the rooms in which lifting stations are installed must be of adequate dimensions so that beside and over all control elements or items where maintenance might be required a working area of at least 60 cm width or...
Page 8
abs lifting station sanimat 4.3 f h k only open inlet posts that are to be used. Saw off as little as possible so that as much material as possible is left for the plug connection. File down sharp edge inside and outside. Attenti...
Page 9
abs lifting station sanimat 4.5 f h bm b m 4.5.1 m f h v 1035-00 figure 6 mounting of volute support attention theareawherethepumpstandsshouldbesmoothandlevel.Thedistancefromthe centrelineofthedischargeporttothecentreli...
Page 10
10 abs lifting station sanimat s bm b m afpm15,m,m30,m40 m60 locate vibration damper (3) at the pump head support (2). Fit the pump head support through ”eyelet a” at the pump head. Adjust the vibration damper (3) so that the rubber support rests on t...
Page 11
11 abs lifting station sanimat control line (3) has a continuous rise as shown in figure 9. The control line should be shortened where necessary, pushed on to the hose nozzle of the submerged tube screw connector (5). The submerged tube screw connector (5) is p...
Page 12
1 abs lifting station sanimat 4. W d m th ph s ph 1013-00 1016-00 figure 10 three phase wiring figure 11 single phase wiring 1014-00 1017-00 figure 12 three phase wiring with temperature limiter figure 13 single phase wiring with temperat...
Page 13
13 abs lifting station sanimat 4.10 ch k f m the safety hints in the previous sections must be observed! When three phase units are being commissioned for the first time and also when used on a new site, the direction of rotation must be ...
Page 14
14 abs lifting station sanimat 5 c mm m the safety hints in the previous sections must be observed! Before commissioning the unit should be checked and a functional test carried out. Particular attention should be paid to the following: have the elect...
Page 15
15 abs lifting station sanimat 6. G m h abs lifting stations are reliable quality products each being subjected to careful final inspection. Lubricated-for- life ball bearings together with monitoring devices ensure optimum pump reliability pr...
Page 16
Abs production wexford ltd., clonard road, wexford, ireland tel. +353 53 91 63 200 fax +353 53 91 42335. Www.Absgroup.Com.