Tc series cutting plotter user’s manual thank you very much for purchasing liyu tm tc series cutting plotter. To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through this manual completely and store it in a safe location. The contents ...
User’s manual of tc series cutting plotter table of contents chap 1 attention.................................................................................…....……….....3 chap 2 part names and functions.....................................................……….……..4 2-1 accessories.....................
User’s manual of tc series cutting plotter chap 1 attention ensure the supply voltage to the tmc series cutting plotter is ac220v and varying within the range of ±10%, otherwise a voltage stabilizer must be used. Please don’t place any small iron-magnetic subject near the carriage. Prevent from drop...
User’s manual of tc series cutting plotter chap 2 part names and functions 2-1 accessories 2-2 introduction of main machine no. Item quantity 1 main machine 1 2 cutter holder 1 3 plotter holder 1 4 refill 1 5 cutter 3 6 usb cable 1 7 power cord 1 8 machine cover 1 9 operation manual 1 10 guarantee c...
User’s manual of tc series cutting plotter 2-3 parts of stand and assembly 1 parts of stand no. Item quantity 1 pillars 4 2 pillar-bars 2 3 left column 1 4 right column 1 5 crossbeam 1 6 paper-hold roller of variable distance 2 7 connection board 2 8 paper roller 2 9 screw m4×20 24 10 screw m4×8 8 2...
User’s manual of tc series cutting plotter 2-4 cutter/plotter 1 structure of cutter holder and items of components rotate the cutter holder to adjust the out-stretching length of the cutter as to ensure that it doesn’t cut off the bottom layer of stickness (consists of upper and bottom layer). 1. Cu...
User’s manual of tc series cutting plotter 2-5 parameters table maximum cutting size 630mm/800mm 1060mm/1260 maximum media size 710mm/880mm 1130 mm/1350 cutting speed cutting force mechanical resolution buffer capacity repeatability motor type interface commands set power requirements environmental ...
User’s manual of tc series cutting plotter chap 3 operation directions 3-1 installation of the usb driver during the installing of the usb driver, any operate to the controlling-panel is invalidation. 1 turn on the power and connect the usb cable with the computer. 2 the device manager will find a n...
User’s manual of tc series cutting plotter 3 select , then click ; 4 select , then click ; ９.
User’s manual of tc series cutting plotter 5 select as following drawing, then click ; 6 click ; １０.
User’s manual of tc series cutting plotter 7 click ,choose the liyudrv and install(in the cd-rom/usb drv); １１.
User’s manual of tc series cutting plotter １２.
User’s manual of tc series cutting plotter 8 click for finish the installation of the usb driver; １３.
User’s manual of tc series cutting plotter 9 after installation，the device will appeared in the device manager as follows， please change the port number according to the require of the computer. １４.
User’s manual of tc series cutting plotter 3-2 controlling-panel operations controlling-panel static screen: in the connecting state, when waiting for the data inputting, lcd displays: spd：6 prs：8 local test copy therein, spd:6 means the current speed is the sixth level, prs:8 means the current pres...
User’s manual of tc series cutting plotter original point: the place of cutter/plotter just at the time of confirming “local” state. Select key: in the static screen state, press this key can select “local”, “test” and “copy” function in sequence. Enter key: after select an option, press this key ca...
User’s manual of tc series cutting plotter test function: under the static screen, press select key to select “test” function, then press enter key, the machine will plot self-check graph. Light:on off: when the cursor in the “on”, press enter key can choose the light on or off, the lcd does not qui...
User’s manual of tc series cutting plotter 3 lift up / adhere when cutting over… 1. Cut off the paper with scissors or a knife. 2. Get rid of the useless part with tweezers (you can easily do this if you add a side frame around the pattern when cutting). 3. Adhere a special “over-pasted film” on the...
User’s manual of tc series cutting plotter chap 4 faq question 1: what shall i do if i can not enter into the cutting system? Answer: 1. The files of the cutting system are damaged. Reinstall the cutting system with the cd-rom enclosed. 2. Check the cutting system is running or not with press the “a...
User’s manual of tc series cutting plotter knifepoint will pick the film and cause the waster. 2. Suggest using the compensation function for best effect when cutting the small pattern. The angle compensation should be set between 0.3mm to 0.5mm according to the fact. 3. The knifepoint should be sho...
User’s manual of tc series cutting plotter question 8: why the paper cannot return to the original point? Answer: 1. Wrong operation on the pinch-rollers. 2. The pinch-rollers is frayed badly. 3. The paper is not loaded rightly. 4. No test running of the paper before cutting the long pattern. Questi...
