Summary of E580 Series
Page 1
E580 series (embedded sim) installation guide.
Page 2: Product Overview
6 7 5 4 4 1 2 3 product overview data in p+d ata out power in data in p+d ata out power in 1 2 power: power led will remain lit while power is applied. Signal strength: indicate receive signal strength. The signal strength leds are only used at the power on to assist the installation. The cpe will t...
Page 3: Install External Sim Card
2 install external sim card notice before installation step 1: unscrew the sim card slot. Step 2: insert a valid sim card into the sim card slot. Push it fully until it clicks into place. Step 3: screw the cap back on tightly . Once the external sim is plug in, the embedded sim will no longer be act...
Page 4: Mount Assembly Package
3 mount assembly package a b c d kit-1 quantity: 1 kit-2 quantity: 1 hex head bolt (m8x50mm) quantity: 2 m8 spring washer quantity: 3 m n o p kit-4 quantity: 1 1/2” u bolt dn63 quantity: 1 m13 washer quantity: 2 m13 spring washer quantity: 2 q 1/2 hexagon nuts quantity: 2 e f washer m8x22 (od) mm qu...
Page 5: Wall-Mount Assembly
4 wall-mount assembly step 1. A b c d e f g h d e f g h i d c j step 2. Step 3. H h h k k k l l l h l k step 1: align the mounting bracket on the wall. Using the bracket as mounting template, mark the positions to drill the holes. Step 2: assemble the bracket as shown in the illustration. Step 3: at...
Page 6: Pole-Mount Assembly
5 pole-mount assembly step 3. H h h k k k l l l h l k step 1. A b c d e f g h d e f g h i d c j step 2. Step 1: align the mounting bracket on the wall. Using the bracket as mounting template, mark the positions to drill the holes. Step 2: assemble the bracket as shown in the illustration. Step 3: at...
Page 7: Insert The Ethernet Cable
6 insert the ethernet cable n o p q m o p q for 1.5” to 2” diameter step 4. N o p q o p q for 2.5” diameter step 4. Unscrew the ethernet port and insert one end of the ethernet cable into the cpe port. Note: for best protection against dust and water, ethernet cable must be fitted with a water-proof...
Page 8: Connect to Pc
7 connect to pc prepare two ethernet cables for connection. Step 1: insert the other end of the ethernet cable to “p+d out” port of the poe adapter. Step 2: connect another ethernet cable to a network hub/router or directly to pc/laptop via poe adapter (“data/in” port). Step 3: plug the poe adapter ...
Page 9: Adjusting Cpe Position
8 adjusting cpe position for optimum reception, fine tune the cpe orientation (horizontally or vertically) to have the best signal strength shown from led or other test equipment. Note: leds (on the front panel) indicate signal strength. Horizontal angle adjustment step 1: loose the top knob using t...
Page 10: Note
9 note if you can not connect to the network, please follow below steps to set apn manually. 1. Go to network > mobile internet > wwan setting- apn profile setting to enter the apn profile name, then click add. 2. Enter apn, user name, and password, then click save. 3. Go to network > mobile inter...
Page 11: Appendix 1.
Appendix 1. Water-proof rj-45 cable jack assembly strip cable sheath recommended wire gauge: 24awg 2 insert the lock nut into the housing. 3 insert the seal at the back end of the housing. 4 insert the cable all the through. Crimp the rj45 plug 1 insert the plug into the hohsing and keep the plug cl...
Page 12: Location and Cable Wiring
11 important installation considerations before installing the outdoor cpe, consider the appropriate location, clearance, and device orientation. Location and cable wiring consult your service provider to find the best location and angle for getting the strongest signal from the base station. mo...
Page 13: Warning:
Warning: to receive stronger signal, please do not place your head or body in front of the cpe while you are positioning the cpe or checking the signal strength leds on the front panel. Position adjustment the cpe must be directed towards the nearest base station. By pointing the cpe in the proper...
Page 14
P/n: 68060211021 rev.A 68060211021.