Barco R9002240 Installation Manual - page 26
Source connections
7-2
5975698 BARCOVISION 1609s 220198
Connecting a S-Video (or Composite Video)
source to Port 2
Separate Y-luma/C-chroma signals for higher quality playback of
Super VHS signals can be connected to Port 2 . A composite video
signal can also be connected to this port.
To select the S-video input :
Press the digit button 2 on the RCU or the local keypad.
In case of using Port 2 for connecting the Composite Video, the
selection of this source have to be done inside the "Picture Tuning"
menu. Please refer to the Owner's Manual.
75 W Termination Switch for S-video
Terminate the S-video input of the projector using the 75
Ω
switch next
to the S-video input when the projector operates alone or when the
projector is the last unit in a loop-through configuration.
The switch is set to "ON" : signal terminated.
The switch is set to "OFF": signal not terminated.
Connecting a RGB Analog source to Port 3
Connect a RGB Analog signal via an interface (e.g. RGB 120MHz
interface, part number 98 26570) to Port 3. RGB analog input with
automatic sync detection (Separate H and V sync inputs, with
composite sync input or with sync signals on green) and automatic
polarity detection.
Pin configuration of the D9 (male) connector of the Analog input :
1
not connected
2
ground RGBS
3
RED
4
GREEN
5
BLUE
6
ground RGBS
7
ground RGBS
8
Horizontal /composite sync
9
Vertical sync
To select the RGB analog Input :
Press the digit button 3 on the RCU or the local keypad.
S1 Force Negative Sync
(ON=yes)
R81
Hsync
R101
Vsync
R41
(Blue)
R21
(Green)
R1
(Red)
S2 Blue in Green (ON=yes)
Line termination 75
Ω
resistors
Locations of the Termination Resistors and Switches
on the RGB Input Auto Sync Tracking Module
When changing a switch position or removing a resistor, turn off the
projector and unplug the power cord from the wall outlet.
75 W Termination resistors
In case of chaining (loop-through) the projectors, the 75
Ω
line
termination resistors must be removed from the RGB Input Auto Sync
Tracking Module when the projector is NOT the last unit in the chain.
In case of a stand-alone projector, do not remove the resistors.
75
Ω
resistors on the module :
line terminated.
75
Ω
resistors removed
:
line not terminated.
1
2
3
4
4 pin connector configurations:
For S-video:
Pin 1: earth(ground) luminance
Pin 2: earth(ground) chrominance
Pin 3: luminance signal(Y)
1Vpp
±
3dB
Pin 4: chrominance signal(C)
300mVpp
±
3dB
For video:
Pin 1: earth(ground) video
Pin 2: not connected
Pin 3: video signal
Pin 4: not connected
RKP
2)) 21
3257
9,'(2
3257
5*%+9
&RPS+V\QF9V\QF
5
*
%
3257
3257
5(027(
&20081,&$7,21
352-(&72502'(
32:(50$,16
3257
69,'(2
RKP
21
2))
*5((1RSHUDWLRQDO
5('VWDQGE\
9&569+6
$XGLRDPSOLILHU
/XPD&KURPD
WRQH[WSURMHFWRURU
WRDPRQLWRU
75
Ω
Termination
Switch
RKP
2)) 21
3257
9,'(2
3257
5*%+9
&RPS+V\QF
9V\QF
5
*
%
3257
32575(027(
&20081,&$7,21
352-(&72502'(
32:(50$,16
3257
69,'(2
RKP
21
2))
*5((1RSHUDWLRQDO
5('VWDQGE\
,13
,13
5
*
%
+
9
,1387
$1$/2*,17(5)0+]
21
2))
LQYHU
RKPWHUP
361
RGB 120MHz interface