Installation & operating manual bunn-o-matic corporation post office box 3227 springfield, illinois 62708-3227 phone: (217) 529-6601 fax: (217) 529-6644 www.Bunnomatic.Com imix ® -3s+ imix ® -3s+a imix ® -5s+ imix ® -5s+a 38987.0000c 09/07 ©2006 bunn-o-matic corporation to obtain the illustrated par...
2 38987 100407 bunn-o-matic commercial product warranty bunn-o-matic corp. (“bunn”) warrants equipment manufactured by it as follows: 1) all equipment other than as specified below: 2 years parts and 1 year labor. 2) electronic circuit and/or control boards: parts and labor for 3 years. 3) compresso...
3 warning ! Fill water tank before turning - on - thermostat or connecting appliance to power source. Use only on a properly protected circuit capable of the rated load. Electrically ground the chassis. Follow national/local electrical codes. Do not use near combustibles. Failure to comply risks equ...
4 initial set-up 1. Apply the four non-skid pads from the parts box to the bottom of the legs. 2. Remove the drip tray assembly, drip tray bracket, and splash panel assembly from the parts box. 3. Place a set of key holes in the drip tray bracket over the lower two screws in the panel below the hopp...
5 38987 121206 plumbing requirements this dispenser must be connected to a cold water system with operating pressure between 20 and 90 psi from a 1⁄2” or larger supply line. A shut-off valve should be installed in the line before the dispenser. Install a regulator in the line when pressure is greate...
6 38987 121206 running a rinse sequence 1. Place the normal/program/rinse switch (page 9) in the “rinse” position. 2. Sequentially at each position, press all of the dispense switches. The dispenser will run for 10 seconds with the hopper(s) disabled. 3. As each position is rinsed, the lcd display w...
7 adjust tank temperature (190° f maximum) adjust minimum tank ready temper- ature for lockout (185° maximum) adjust hopper motor speed for station selected tank temp xxx° (-) exit (+) ready temp xxx° (-) exit (+) drink strength (-) xx (+) xx° cal xx° (-) tank temp (+) 235 refill 155 (-) exit (+) po...
8 d igital b everage c ontrol d igital b everage c ontrol stop program home screen the screen above will be shown when the dispenser is ready for use. While the tank is heating, the water temperature will be displayed until the ready temperature is reached. Programming the dispenser the following fu...
9 programming cup sizes - portion control models the cup size can be programmed in portion control models by “example” or “time”. Programming by ex- ample is manually pressing desired dispense button, then releasing when the desired cup size is attained. The time required to fill the cup will be sto...
10 portion control ? No exit yes press and release right switch (advance to next menu), “tank temp xxx°” appears on screen. Programming the dispenser (cont.) tank temp xxx° ready temp xxx° (-) exit (+) strength adj. ? (-) exit (+) exit yes enter password (-) xxxx (+) calibration ? Exit yes locks/dis...
11 xx° cal xx° (-) tank temp (+) programming the dispenser (cont.) drink strength 1 (-) xx (+) press dispense to check taste taste 1 ok ? No yes (b) adjust hopper motor speed for station selected select units eng exit metric (d) 235 refill 155 (-) exit (+) auger delay (-) .Xx sec (+) returns to (e) ...
12 programming the dispenser (cont.) rinse alarm ? No exit yes head 1 disable ? No exit yes set password ? (-) xxxx (+) returns to (g) (page 10) test switches ? Use switch to test test heater ? Exit yes test refill ? Exit yes test hot water ? Exit yes test augers ? Dispense to test test dispense hea...
13 electrical schematic 38986.0000b 09/07 ©2006 bunn-o-ma tic corpor at ion 120 vol ts ac - 2 wire single phase, 60hz schema tic wiring dia gram imix-3s+ / imix-5s+ grn blk-1 6 blk-1 6 limit thermost at j4-5 j4-1 j4-10 j4-15 j4-20 j4-24 j5-5 j5-1 j2-6 j2-1 j3-4 j5-4 j3-1 j5-1 ballas t #1 bl k grn/bl...
14 electrical schematic 38987 091407.
