Imix ® -3s+ imix ® -3s+a imix ® -5s+ imix ® -5s+a installation & operating guide bunn-o-matic corporation post office box 3227 springfield, illinois 62708-3227 phone: (217) 529-6601 fax: (217) 529-6644 to ensure you have the latest revision of the operating manual, or to view the illustrated parts c...
2 38987 080112 bunn-o-matic commercial product warranty bunn-o-matic corp. (“bunn”) warrants equipment manufactured by it as follows: 1) airpots, thermal carafes, decanters, gpr servers, iced tea/coffee dispensers, mcp/mca pod brewers thermal servers and thermofresh servers (mechanical and digital)-...
3 warning ! Fill water tank before turning - on - thermostat or connecting appliance to power source. Use only on a properly protected circuit capable of the rated load. Electrically ground the chassis. Follow national/local electrical codes. Do not use near combustibles. Failure to comply risks equ...
4 electrical requirements caution - the dispenser must be disconnected from the power source until specified in electrical hook-up. The 120 volt version of this dispenser has an attached cordset. The mating connector must be a nema 5-15r. To access terminal block for high voltage models without a co...
5 38987 010813 plumbing requirements this dispenser must be connected to a cold water system with operating pressure between 20 and 90 psi from a 1⁄2” or larger supply line. A shut-off valve should be installed in the line before the dispenser. Install a regulator in the line when pressure is greate...
6 38987 012210 running a rinse sequence 1. Place the normal/program/rinse switch (page 9) in the “rinse” position. 2. Sequentially at each position, press all of the dispense switches. The dispenser will run for 10 seconds with the hopper(s) disabled. 3. As each position is rinsed, the lcd display w...
7 cleaning the use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all sur- faces on bunn-o-matic equipment. Do not clean this equipment with a water jet device. 1 x 24h 37254.0000a 07/04 © 2004 bunn-o-matic corporation notice the cleaning instructions ...
8 adjust tank temperature (190° f maximum) adjust minimum tank ready temper- ature for lockout (185° maximum) adjust hopper motor speed for station selected tank temp xxx° (-) exit (+) ready temp xxx° (-) exit (+) drink strength (-) xx (+) xx° cal xx° (-) tank temp (+) 235 refill 155 (-) exit (+) po...
9 d igital b everage c ontrol d igital b everage c ontrol stop program home screen the screen above will be shown when the dispenser is ready for use. While the tank is heating, the water temperature will be displayed until the ready temperature is reached. Programming the dispenser the following fu...
10 programming cup sizes - portion control models the cup size can be programmed in portion control models by “example” or “time”. Programming by ex- ample is manually pressing desired dispense button, then releasing when the desired cup size is attained. The time required to fill the cup will be st...
11 portion control ? No exit yes press and release right switch (advance to next menu), “tank temp xxx°” appears on screen. Programming the dispenser (cont.) tank temp xxx° ready temp xxx° (-) exit (+) strength adj. ? (-) exit (+) exit yes enter password (-) xxxx (+) calibration ? Exit yes locks/dis...
12 xx° cal xx° (-) tank temp (+) programming the dispenser (cont.) drink strength 1 (-) xx (+) press dispense to check taste taste 1 ok ? No yes (b) adjust hopper motor speed for station selected select units eng exit metric (d) 235 refill 155 (-) exit (+) auger delay (-) .Xx sec (+) returns to (e) ...
13 programming the dispenser (cont.) rinse alarm ? No exit yes head 1 disable ? No exit yes set password ? (-) xxxx (+) returns to (g) (page 11) test switches ? Use switch to test test heater ? Exit yes test refill ? Exit yes test hot water ? Exit yes test augers ? Dispense to test test dispense hea...
