Canon i-SENSYS D450d Service Manual - page 172
Chapter 14
14-16
14.3.2 Faculty Test
14.3.2.1 Print test pattern
0020-2793
i-SENSYS MF4300dn / i-SENSYS MF4350d / i-SENSYS MF4380dn / i-SENSYS MF4310/4318 / i-SENSYS MF4320d / i-SENSYS MF4330d / i-SENSYS
MF4340d / i-SENSYS D450d / i-SENSYS MF4370dn
From the FUNCTION menu, select PRINT TEST PATTERN.
In this test, the printer unit will be used to print various patterns. For service work, be sure to use the BLACK pattern and the SQUARE pattern.
Use the BLACK print pattern to meke sure that the printout is free of white lines and unevenness; on the other hand, use the SQUARE printout to make sure that
the printout is free of image contraction, elongation, and soiling.
MEMO
After completion of the print test, if the printing was normal, copy a document. If there is any defect in the copied image, there is a defect in the scan
section.
14.3.2.2 êMçÜÉeÉXÉg
0020-2794
i-SENSYS MF4300dn / i-SENSYS MF4350d / i-SENSYS MF4380dn / i-SENSYS MF4310/4318 / i-SENSYS MF4320d / i-SENSYS MF4330d / i-SENSYS
MF4340d / i-SENSYS D450d / i-SENSYS MF4370dn
H/W
TESTÉÅÉjÉÖÅ[Ç©ÇÁSIGNAL
TESTÇšëIëšÇ²ÇÈÅBDZÇÃÉeÉXÉgÇÝÇÕÅAñ{ã@ÇÃÉÇÉfÉÄÇ©ÇÁìdòbâÒê¸ê
⁄ë±í[éqÇýÉXÉsÅ[ÉJÇ©ÇÁêMçÜÇšëóèoDzÇÈÅB
14.3.2.3 Sensor test
0020-2795
i-SENSYS MF4300dn / i-SENSYS MF4350d / i-SENSYS MF4380dn / i-SENSYS MF4310/4318 / i-SENSYS MF4320d / i-SENSYS MF4330d / i-SENSYS
MF4340d / i-SENSYS D450d / i-SENSYS MF4370dn
SENSOR TEST is selected from the H/W TEST menu. In this test, the state of each sensor of this machine can be checked on the display. For the sensor that uses
the sensor arm and the microswitch, the output of the sensor can be confirmed by moving them by the hand.
T-14-19
14.3.2.4 Key test
0020-2796
i-SENSYS MF4300dn / i-SENSYS MF4350d / i-SENSYS MF4380dn / i-SENSYS MF4310/4318 / i-SENSYS MF4320d / i-SENSYS MF4330d / i-SENSYS
MF4340d / i-SENSYS D450d / i-SENSYS MF4370dn
KEY TEST is selected from the H/W TEST menu. In this test, whether the button on the operation panel works correctly can be checked.
Operation key test
In this test, the character on the display disappears when the key corresponding to the character is pushed. The correspondence table of the character and
the key is as follows.
When the key is pushed for all keys, it is checked that the corresponding character on the display disappears.
T-14-20
çÄñ
⁄
ì‡óe
TX FSK
300bpsêMçÜëóèo
TX PSK
2400Å`14400bpsêMçÜëóèo
CED (2100HzÅj
CEDêMçÜëóèo
CNG (1100Hz)
CNGêMçÜëóèo
V.34 SIGNAL TX
V.34êMçÜëóèo
Test
Function
Action
HOOK 1/2 DETECT
Handset status
OFF:inactive ON:Active
ADF DS TEST
ADF detect
OFF:inactive ON:Active
ADF DES TEST
ADF detect
OFF:inactive ON:Active
CRG TEST
Toner Cartridge detect
OFF:inactive ON:Active
TN Value
Display Toner remain value
from 0 to 127
RING DETECT
Ring detect
OFF:inactive ON:Active
Character
Operation button
Character
Operation button
Character
Operation button
0-9,*,#
Numeric key, tone key
K
[Start] key
V
[Hook] key
A
[COPY] key
L
[Clear] key
a
One-Touch Speed Dial
[01] key
B
[SCAN] key
M
[Energy Saver] key
b
One-Touch Speed Dial
[02] key
C
[Additional
Functions] key
N
[View Settings] key
c
One-Touch Speed Dial
[03] key
D
[System Monitor] key
O
[2-Sided] key
d
One-Touch Speed Dial
[04] key
E
[Enlarge/Reduce] key
P
[Toner Gauge] key
e
One-Touch Speed Dial
[05] key
F
[Density] key
Q
[OK] key
f
One-Touch Speed Dial
[06] key
G
[Image Quality] key
R
[FAX] key
g
One-Touch Speed Dial
[07] key
H
[Collate/2 on 1] key
S
[Address Book] key
h
One-Touch Speed Dial
[08] key or [Reset] key