Summary of Terrier 200
Page 1
1 installation guide by easygate for terrier swing gate system.
Page 2
2 installation notes by easygate for terrier swing gate arm using cb17 control board. Unpack product. Check that all items are present and are in good condition. Check also inside the control box for remotes and other product that may have been packed inside. Before each order is dispatched a check ...
Page 3
3 post bracket pin and wear bush location in tongue plate hole arm to gate bracket with pin and crub screw key to assist opening clutch lever fully open ram retracted. Fully closed ram extended..
Page 4
4 fitting the arm cable: step 1 – remove the cover screws. Step 2 – push up the cover slightly. Step 3 – some models have a 2 x tab system while others have 3 x screw fasteners. On the back, insert a flat head screw driver in slots, push forward tabs to release hooks step 5 – insert cable from under...
Page 5
5 the arm if you get the symbols wrong. When you test the system and note an arm is going the wrong way, just rotate the arm cable wires that are configured wrong and test again until you get both arms opening on first power up of the board. Wiring single gate: connect arm cable to blocks labelled m...
Page 6
6 the system is delivered with the ac transformer and the dc battery male connector plugs (white). You will need to plug these in to the matching female connector blocks on the corner of the control board. A clip is fitted to the side of the plug to correctly align with the female plug side catcher....
Page 7
7 double gate system learn: this must be completed when first installing the control board so the computer can understand the parameters of the new installation. 1. Check you have sw2 set dip switch 8 to on 2. Press the sys-learn button which is next to the rf-learn button in the top left corner. Ho...
Page 8
8 7. After the systems learn has finished, led no.1 should be revert back to flashing in bursts. You have successfully set up your gate opener kit and is now ready for testing. Dip switch overview: the switches that you will see to the left hand side on the control board are separated into 3 banks a...
Page 9
9 the auto close timer will start when the gates are either fully open or stopped through a cycle. Activating a remote or any other device will override the timer and close the gates immediately. Sw1 pedestrian mode this function will open one side of the gates to a 45 degree angle to allow pedestri...
Page 10
10 the following functions are all on sw3 (bottom block of switches). Switches: 1 and 2 this function is to select the command button of the remote option 1 (default setting for double gate) 1 on button a for double gate operation button b for single gate operation 2 off option 2 (setting for single...
Page 11
11 led lights led lights: these lights serve several functions. They are the indicators to see if the system is operating as it should or not. Led 1 system learning two flashes followed by 1 second pause = standby mode for double gate. Single flash followed by a 1 second pause = standby mode for a s...
Page 12
12 sw3… switch 1 (1.Remote_1) to on, switch 2 (2.Remote_2) off, switch 3 (3.Ph_conn1) off, switch 4 (4.Ph_conn2) on. If installing 2 pairs of beams simply repeat the above sequence and change the following: run the wire from normally closed to fo2 and change sw3 switch 3 to on. Installing optional w...
Page 13
13 4. Fo + 13.7v dc positive (+) power for photo beams 5. G ground/negative/common (-). 6. D activation devises on a dual gate operator such as keypad, exit button, intercom, dial to open. Used with terminal 8. 7. S activation single gate operator 8. G common. Used in conjunction with terminal 7 or ...
Page 14
14 remotes or wireless keypad not working. - re program remotes by pressing the rf learn button until a blue light next to it comes on. Press the remote once and it should flicker. Now wait until the light goes off and try again. - you can program in several remotes or devices at a time however all ...
Page 15
15 gates remain open after systems learn/one arm stays open and the other one closed. - ensure you have matched the + and - of each ram to the equivalent + and – motor symbols on the board. - clear any obstructions to the gates. - make sure that the rams are going no further than 100 degrees. - the ...
Page 16
16 primeval nz ltd trading as easygate warrants, on behalf of the manufacturer, the original purchasers for a period of one (1) year unless stated below. Warranty commences from date of purchase (not installation). The manufacturer warrants the product to be free of defects in materials and workmans...
Page 17
17 easygate will at this option repair or replace out-of-warranty products which are returned to its factory according to the following conditions. Anyone returning goods to easygate must first obtain an authorization number. Easygate will not accept any shipment whatsoever for which prior authoriza...
Page 18
18 the expected battery life is a function of the device environment, usage and type. Ambient conditions such as high humidity, high or low temperatures, or large temperature fluctuations may reduce the expected battery life. Low battery condition will cause the system in low power condition and hav...