1. DL manuals
  2. Eaton
  3. UPS
  4. Powerware 9395
  5. Installation And Operation Manual

Eaton Powerware 9395 Installation And Operation Manual

Manual is about: 450–825 kVA Powerware Series

Summary of Powerware 9395

  • Page 1

    Powerware series eaton 9395 ups, plus 1 ups, and 825/550 ups 450–825 kva installation and operation manual ® for use with two upm (450–550 kva), three upm (650–825 kva), and plus 1 (650–825 kva) ups models.

  • Page 3

    Powerware series eaton 9395 ups, plus 1 ups, and 825/550 ups 450–825 kva installation and operation manual ® for use with two upm (450–550 kva), three upm (650–825 kva), and plus 1 (650–825 kva) ups models.

  • Page 4

    Important safety instructions save these instructions this manual contains important instructions that you should follow during installation and maintenance of the ups and batteries. Please read all instructions before operating the equipment and save this manual for future reference. Consignes de s...

  • Page 5

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality i table of contents 1 introduction 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1...

  • Page 6

    Table of contents eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality ii 4.7 distributed bypass tie cabinet installation 4-23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 7

    Table of contents eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality iii 7.2 using the control panel 7-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 8

    Table of contents eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality iv 7.4.16 starting a single upm 7-41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 9

    Table of contents eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality v list of figures figure 1‐1. Eaton 9395 three upm ups (650–825 kva) 1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 10

    Table of contents eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality vi figure 4‐21. Typical bus bar barrel lug mounting – hardware assembly sequence 4-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 4‐22....

  • Page 11

    Table of contents eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality vii figure 6‐7. Plus 1 ups system – four upm, common rectifier feed, common battery, dual‐feed configuration, momentary static switch 6-12 . . . . . . . . . . . . . . . . . ....

  • Page 12

    Table of contents eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality viii figure 7‐3. Ups control panel 7-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 13

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 1-1 chapter 1 introduction the eaton ® 9395 uninterruptible power supply (ups) is a true online, continuous-duty, transformerless, double-conversion, solid-state, three-phase system, providing...

  • Page 14

    Introduction eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 1-2 upm section isbm or iom section figure 1‐1. Eaton 9395 three upm ups (650–825 kva) upm section fi-upm isbm or iom section figure 1‐2. Eaton 9395 plus 1 ups (650–825 kva) with ...

  • Page 15

    Introduction eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 1-3 upm section isbm or iom section figure 1‐3. Eaton 9395-825/550 two upm ups (450–550 kva) upm section isbm or iom section figure 1‐4. Eaton 9395-825/550 two upm ups with the fi...

  • Page 16

    Introduction eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 1-4 1.1 ups standard features the ups has many standard features that provide cost‐effective and consistently reliable power protection. The descriptions in this section provide a...

  • Page 17

    Introduction eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 1-5 1.2 options and accessories contact an eaton sales representative for information about the following options. 1.2.1 field installed upm a field installed upm (fi-upm) provide...

  • Page 18

    Introduction eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 1-6 the tie cabinet must contain module output breakers (mobs) with dual auxiliary contacts for control of the system. Without dual auxiliary mobs, upms are not allowed to go to b...

  • Page 19

    Introduction eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 1-7 1.2.10 variable module management system and high alert modes note the variable module management system and energy saver system modes are mutually exclusive. The variable mod...

  • Page 20

    Introduction eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 1-8 1.3 battery system although not provided with the ups, a battery system is required to provide emergency short-term backup power to safeguard operation during brownouts, black...

  • Page 21

    Introduction eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 1-9 1.5 using this manual this manual describes how to install and operate the eaton 9395 450–825 kva ups. Read and understand the procedures described in this manual to ensure tr...

  • Page 22

    Introduction eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 1-10 1.7 symbols, controls, and indicators the following are examples of symbols used on the ups or accessories to alert you to important information: risk of electric shock - obs...

  • Page 23

    Introduction eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 1-11 1.9 getting help if help is needed with any of the following: s scheduling initial startup s regional locations and telephone numbers s a question about any of the informatio...

  • Page 24

    Introduction eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 1-12 this page intentionally left blank..

  • Page 25

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 2-1 chapter 2 safety warnings important safety instructions save these instructions this manual contains important instructions that should be followed during installation and maintenance of t...

  • Page 26

    Safety warnings eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 2-2 s the operating environment should be maintained within the parameters stated in this manual. S keep surroundings uncluttered, clean, and free from excess moisture. S obser...

  • Page 27

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 2-1 section i installation.

  • Page 28

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 2-2.

  • Page 29

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-1 chapter 3 ups installation plan and unpacking use the following basic sequence of steps to install the ups: 1. Create an installation plan for the ups system (chapter 3). 2. Prepare your s...

  • Page 30

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-2 table 3‐1. Ups cabinet weights model section weight kg (lb) shipping installed eaton 9395-825/450 isbm (css) 797 (1757) 729 (1607) upm (two upm) 1159 (2...

  • Page 31

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-3 the basic environmental requirements for operation of the ups are: s ambient temperature range: 0–40°c (32–104°f) s recommended operating range: 20–25°c...

  • Page 32

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-4 dimensions are in millimeters [inches]. Figure 3‐1. Ups cabinet dimensions – three upm (front view) dimensions are in millimeters [inches]. Figure 3‐2. ...

  • Page 33

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-5 figure 3‐3. Ups cabinet dimensions (right side view) dimensions are in millimeters [inches]. Figure 3‐4. Isbm section dimensions (front view).

  • Page 34

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-6 dimensions are in millimeters [inches]. Figure 3‐5. Upm section dimensions – three upm (front view) dimensions are in millimeters [inches]. Figure 3‐6. ...

  • Page 35

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-7 front dimensions are in millimeters [inches]. Figure 3‐7. Isbm section dimensions (top view) front dimensions are in millimeters [inches]. Figure 3‐8. I...

  • Page 36

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-8 front dimensions are in millimeters [inches]. Figure 3‐9. Upm section dimensions – three upm (top view) front dimensions are in millimeters [inches]. Fi...

  • Page 37

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-9 dimensions are in millimeters [inches]. Cg cg figure 3‐11. Isbm section center of gravity – momentary static switch dimensions are in millimeters [inche...

  • Page 38

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-10 dimensions are in millimeters [inches]. Cg cg figure 3‐13. Upm section center of gravity – three upm dimensions are in millimeters [inches]. Cg cg figu...

  • Page 39

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-11 dimensions are in millimeters [inches]. 115.8 [4.56] 114.3 [4.50] 0.87 [0.22] 88.9 [3.50] front view 1.57 [0.40] needed to remove key 95.3 [3.57] (squa...

  • Page 40

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-12 s if the load requires a neutral, a bypass source neutral must be provided. If the load does not require a neutral and there is no neutral conductor co...

  • Page 41

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-13 if the power rating listed on the nameplate of the installed ups is not found in the following tables, wire the ups using the fully rated specification...

  • Page 42

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-14 table 3‐4. Input/output ratings and external wiring requirements for the three upm eaton 9395-825/650, 9395-825/750, and 9395-825/825 – common battery ...

  • Page 43

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-15 table 3‐5. Input/output ratings and external wiring requirements for the three upm eaton 9395-825/650, 9395-825/750, and 9395-825/825 – separate batter...

  • Page 44

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-16 table 3‐6. Input/output ratings and external wiring requirements for the two upm eaton 9395-825/450, 9395-825/500, and 9395-825/550 – common battery ba...

  • Page 45

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-17 table 3‐7. Input/output ratings and external wiring requirements for the two upm eaton 9395-825/450, 9395-825/500, and 9395-825/550 – separate battery ...

  • Page 46

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-18 ac input to the ups with separate rectifier inputs is wired as if each upm is rated for 275 kva (see table 3‐8). The bypass input, battery input, and o...

  • Page 47

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-19 terminals e1a through e5a and e9a through e12a are stud type terminals. The intercabinet power wiring connections for this equipment are rated at 90°c....

  • Page 48

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-20 for a ups with common rectifier input terminals, e1 through e12 are 2‐hole bus bar mountings for standard nema 2‐hole barrel lugs. The power wiring con...

  • Page 49

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-21 table 3‐12. Supplied external wiring terminal hardware kit part size quantity terminals used on eaton part number bolt, grade 5 m10 x 25 mm 15 ground 1...

  • Page 50

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-22 conduit sizes were chosen from nec table 4, electrical metallic tubing (emt). See table 3‐15 for conduit requirements. Per nec article 300, 3(b)(1), al...

  • Page 51

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-23 table 3‐15. Power cable conduit requirements (continued) number of conduits minimum conduit trade size number of wires in conduit terminal voltage ups ...

  • Page 52

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-24 external overcurrent protection and disconnect are not provided by this product, but are required by codes. See to table 3‐4 on page 3-14, table 3‐5 on...

  • Page 53

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-25 c a u t i o n to reduce the risk of fire, connect only to a circuit provided with maximum input circuit breaker current ratings from table 3‐16 in acco...

  • Page 54

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-26 table 3‐19. Recommended dc input battery disconnect ratings – common battery ups model input rating 400v 480v eaton 9395-825/650 1600a 1600a eaton 9395...

  • Page 55

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-27 3.2.3 ups system interface wiring preparation control wiring for features and options should be connected at the customer interface terminal blocks loc...

  • Page 56

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-28 s the repo switch wiring must be in accordance with nec article 725 class 2 requirements. S the maximum distance between the repo and the ups cannot ex...

  • Page 57

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-29 3.3 inspecting and unpacking the ups cabinets the ups cabinet is divided into two sections palleted separately for shipping. The sections are shipped b...

  • Page 58

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-30 4. Remove the protective covering from the cabinets. 5. Remove the packing material, and discard or recycle in a responsible manner. 6. Inspect the con...

  • Page 59

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-31 figure 3‐17. Ups cabinet as shipped on pallet (upm section – three upm).

  • Page 60

    Ups installation plan and unpacking eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 3-32 figure 3‐18. Ups cabinet as shipped on pallet (upm section – two upm).

  • Page 61

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-1 chapter 4 ups system installation 4.1 preliminary installation information w a r n i n g installation should be performed only by qualified personnel. Refer to the following while installi...

  • Page 62

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-2 note for the following steps, verify that the forklift or pallet jack is rated to handle the weight of the cabinet (see table 3‐1 on page 3-2 for cabinet weight). 1...

  • Page 63

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-3 shipping bracket bolts shipping bracket bolts pallet right side shipping bracket isbm removable front panels figure 4‐2. Removing the isbm section right side shippi...

  • Page 64

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-4 shipping bracket bolts shipping bracket bolts pallet left side shipping bracket upm removable front panels wireway panel figure 4‐3. Removing the three upm section ...

  • Page 65

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-5 shipping bracket bolts shipping bracket bolts pallet right side shipping bracket figure 4‐4. Removing the three upm section right side shipping bracket.

  • Page 66

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-6 shipping bracket bolts shipping bracket bolts pallet left side shipping bracket upm removable front panels wireway panel figure 4‐5. Removing the two upm section le...

  • Page 67

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-7 shipping bracket bolts shipping bracket bolts pallet right side shipping bracket figure 4‐6. Removing the two upm section right side shipping bracket 4.3 mechanical...

  • Page 68

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-8 left top panel wireway panel left middle panel corner channel upm section interior left side panel figure 4‐7. Section joining (three upm section shown) 5. Remove t...

  • Page 69

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-9 upm wireway (power wiring harnesses are coiled in this area.) figure 4‐8. Isbm and upm sections joined (three upm section shown) 10. Reinstall the left top panel (s...

  • Page 70

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-10 front view base bracket upm section base isbm section base bracket from kit screw from kit screw from kit top view rear bracket upm section top isbm section top sc...

  • Page 71

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-11 note the 3g1 and 3g2 yellow, orange, and brown ac input intercabinet power wiring harnesses are not supplied with the eaton 9395-825/550 two upm ups model. 5. Loca...

  • Page 72

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-12 note the 3g4 and 3g4 yellow, orange, brown, and gray ac output intercabinet power wiring harnesses are not supplied with the eaton 9395-825/550 two upm ups model. ...

  • Page 73

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-13 note one intercabinet interface cable is supplied coiled against the left side panel of the upm section (see b in figure 4‐18 on page 4-21). 20. In the upm section...

  • Page 74

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-14 (see figure 4‐11 for detail.) ac input to upms ac output from upms phase c phase a phase b neutral from upms (see figure 4‐17 for detail.) (see figure 4‐17 for det...

  • Page 75

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-15 upm 1 cable 1g1 & 1g2 yellow phase c (e3a) upm 2 cable 2g1 & 2g2 yellow upm 3 cable 3g1 & 3g2 yellow ac input breaker cb1 upm 1 cable 1g1 & 1g2 orange phase a (e1a...

  • Page 76

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-16 (see figure 4‐13 for detail.) ac input to upms ac output from upms phase c phase a phase b neutral from upms (see figure 4‐17 for detail.) (see figure 4‐17 for det...

  • Page 77

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-17 note two cable lugs will be connected to each terminal stud. When connecting the cable lugs, install the first lug on the stud with the raised barrel portion facin...

  • Page 78

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-18 (see figure 4‐15 for detail.) ac input to upms ac output from upms phase c phase a phase b neutral from upms (see figure 4‐17 for detail.) (see figure 4‐17 for det...

  • Page 79

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-19 upm 1 cable 1g1 & 1g2 yellow phase c (e3a) upm 2 cable 2g1 & 2g2 yellow upm 3 cable 3g1 & 3g2 yellow upm 1 cable 1g1 & 1g2 orange phase a (e1a) upm 2 cable 2g1 & 2...

  • Page 80

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-20 dc input to upms + cable 1g3 black upm 1 (1e5a) cable 1g3 black dc input to upms cable 1g3 red upm 1 (1e4a) cable 1g3 red – cable 2g3 black upm 2 (2e5a) cable 2g3 ...

  • Page 81

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-21 wiring access location of j50, j51, j61, and j70 coiled harnesses location of rj-45 coiled can cable upm wireway location of p61 harness location of p50, p51, and ...

  • Page 82

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-22 isbm section right side inside view pl1 interface board front figure 4‐19. Pl1 interface board location pl1 interface board j39 inverter can connector figure 4‐20....

  • Page 83

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-23 4.5 field installed upm installation if installing a plus 1 model or adding the fi-upm to an 825/550 model, install the fi-upm using the instructions in the eaton ...

  • Page 84

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-24 use the procedures in the following paragraphs to connect the external and battery power wiring. 4.8.1 2‐hole barrel lug terminations to bus bar installation parag...

  • Page 85

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-25 4.8.2 external power wiring installation to install wiring to connections: 1. Remove one top screw and two bottom screws securing each isbm section left and right ...

  • Page 86

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-26 isbm section front ventilation grill debris shields (remove shields before operating system.) three upm section front two upm section front ventilation grill debri...

  • Page 87

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-27 top entry conduit landing for ac input and output, and dc input (remove panel to drill or punch conduit holes.) top view interface entry conduit landings for tb1 t...

  • Page 88

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-28 6. Connect phase a, b, and c rectifier input power wiring from the utility source to each upm rectifier input terminal block in the ups cabinet. See paragraph 3.2....

  • Page 89

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-29 note required parallel system wiring length must be equal to ensure approximately equal current sharing when in bypass mode. For proper operation the following mus...

  • Page 90

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-30 (see figure 4‐26 for detail aa.) dc input from battery + (e4) – (e5) dc input from battery ac input to ups rectifier (a, b, c) ac input to ups bypass (a, b, c) (se...

  • Page 91

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-31 ground terminals phase a (e6) phase c (e8) phase b (e7) ac input to ups rectifier phase c (e3) phase a (e1) phase b (e2) ac input to ups bypass ` section a–a front...

  • Page 92

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-32 note ac input to bypass terminals are not applicable to an iom configuration. (see figure 4‐28 for detail aa.) dc input from battery + (e4) – (e5) dc input from ba...

  • Page 93

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-33 phase a (e6) phase c (e8) phase b (e7) ac input to ups rectifier phase a (e1) phase c (e3) phase b (e2) ac input to ups bypass ` front section a–a ground terminals...

  • Page 94

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-34 a b c n (see figure 4‐30 for detail aa.) dc input from battery + (e4) – (e5) dc input from battery ac input to ups rectifier (a, b, c) ac input to ups bypass (a, b...

  • Page 95

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-35 ground terminals phase a (e6) phase c (e8) phase b (e7) ac input to ups bypass ` note ac input to bypass terminals are not applicable to an iom configuration. Sect...

  • Page 96

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-36 ac input to upm rectifiers phase a (e1) phase c (e3) phase b (e2) upm 4 (fi-upm) upm 2 upm 1 upm 3 phase a (e1a) phase c (e3a) phase b (e2a) ac input to upm 4 (fi-...

  • Page 97

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-37 4.8.3 battery power wiring c a u t i o n when sizing the battery system, do not exceed the internal battery charger capabilities. See chapter 10, “product specific...

  • Page 98

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-38 dc input from battery + (e4) – (e5) dc input from battery section b–b front figure 4‐32. Isbm section power terminal detail bb – common battery.

  • Page 99

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-39 dc input from battery + (e4) – (e5) dc input from battery dc input from battery + (e4) (upm 1) (upm 3) – (e5) dc input from battery (upm 2) section b–b front – (e5...

  • Page 100

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-40 4.9 installing interface connections w a r n i n g hazardous voltages are present near the user interface terminal area if the ups is not totally disconnected. Use...

  • Page 101

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-41 11. Reinstall the front door removed in step 3 and secure with the retained hardware. 12. Close the door and secure the latch. X-slot communication bays tb3 tb1 an...

  • Page 102

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-42 table 4‐1. Tb1, tb2, and tb3 interface connections terminal tb1 name description 1 repo nc input: normally‐closed dry contact used to activate ups epo from a remot...

  • Page 103

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-43 x-slot communication bays tb1 tb2 see figure 4‐37 for terminal assignments. Figure 4‐35. Interface terminal detail tb2 note alarm relay contacts have a maximum cur...

  • Page 104

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-44 ups building alarm 3 building alarm 3 return building alarm 4 building alarm 5 building alarm 4 return building alarm 5 return note all building alarm inputs requi...

  • Page 105

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-45 4.9.2 tb1 battery interface connections to install wiring to connections: 1. Verify the ups system is turned off and all power sources are removed. See chapter 7, ...

  • Page 106

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-46 battery disconnect tb1 battery aux battery aux common 48 vdc battery shunt trip + 48 vdc battery shunt trip – ups st 5 6 7 8 note battery aux and dc shunt trip wir...

  • Page 107

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-47 4.9.3 x-slot connections note lan and telephone drops for use with x-slot cards must be provided by the customer. Note when installing external wiring to x-slot ca...

  • Page 108

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-48 4.10 installing a repo switch a latching-type remote emergency power-off (repo) switch can be used in an emergency to shut down the ups and remove power to the cri...

  • Page 109

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-49 5. To gain access to terminal block tb1 and the interface entry conduit landing plate, remove the screws securing the top internal safety shield panel and remove t...

  • Page 110

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-50 12. If required, install wiring from the repo switch to the trip circuitry of the upstream protective devices. A second contact block is provided on the repo switc...

  • Page 111

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-51 3 (no) ups tb1 repo switch (no) twisted wires 1 (nc) 2 (return) 4 (return) repo switch (nc) note repo switch rating is 24 vdc, 1a minimum. Note the repo switch mus...

  • Page 112

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-52 installation checklist - all packing materials and restraints have been removed from each cabinet. - each cabinet in the ups system is placed in its installed loca...

  • Page 113

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-53 distributed bypass installation checklist - each cabinet in the distributed bypass system is placed in its installed location. - all conduits and cables are proper...

  • Page 114

    Ups system installation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 4-54 notes _________________________________________________________________________ _________________________________________________________________________ _________...

  • Page 115

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-1 chapter 5 installing options and accessories 5.1 installing an optional powerware hot sync can bridge card as an option, a powerware hot sync controller area network (can) bridge card, sho...

  • Page 116

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-2 4. Read and understand the following notes while planning and performing the wiring installation: s conduit must be installed between the ups cabinet and...

  • Page 117

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-3 connections for parallel system control connections for rmp ii, rim ii, or scm ii alarm j3 connections for bypass status figure 5‐2. Powerware hot sync c...

  • Page 118

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-4 5.2 installing distributed bypass control wiring note when installing external wiring to the powerware hot sync can bridge card, conduit must be installe...

  • Page 119

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-5 ups 1 ups 2 ups 3 ups 4 can (if installed) (if installed) pull chain note this drawing is for distributed bypass wiring purposes and is not a floor layou...

  • Page 120

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-6 1 2 3 4 5 7 8 6 9 10 ups 1 twisted pair twisted pair twisted pair twisted pair twisted pair twisted pair 1 2 3 4 5 7 8 6 9 10 1 2 3 4 5 7 8 6 9 10 ups 2 ...

  • Page 121

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-7 note nc and no designations on mob aux contacts are defined with breaker in off (open) position. Note if mob contacts have pigtail leads, use the same wi...

  • Page 122

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-8 table 5‐4. Pull-chain wiring terminations with mobs from to function ups 1 can bridge card j3–1 (alarm) mob 1 aux 1 nc mob open alarm ups 1 can bridge ca...

  • Page 123

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-9 5.3 installing an optional remote monitor panel ii to install rmp ii wiring: 1. Verify the ups system is turned off and all power sources are removed. Se...

  • Page 124

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-10 terminal tb1 signal connections from the ups ground terminal terminal tb3 120 vac power figure 5‐7. Remote monitor panel ii and relay interface module i...

  • Page 125

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-11 note setup of the powerware hot sync can bridge card must be performed by an authorized eaton customer service engineer. Contact an eaton service repres...

  • Page 126

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-12 10. Restart the ups. See chapter 7, “ups operating instructions,” for startup instructions. Note setup of the powerware hot sync can bridge card must be...

  • Page 127

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-13 5.5 installing an optional supervisory contact module ii to install scm ii wiring: 1. Verify the ups system is turned off and all power sources are remo...

  • Page 128

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-14 note setup of the powerware hot sync can bridge card must be performed by an authorized eaton customer service engineer. Contact an eaton service repres...

  • Page 129

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-15 5.6 accessory mounting dimensions figure 5‐12 through figure 5‐14 show the dimensions of the rmp ii, the rim ii, and the scm ii. Flush mount using #10 p...

  • Page 130

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-16 knockouts provided on five surfaces surface mount using #10 pan head screws for hanging. (mount with vent holes facing up.) flush mount using #10 pan he...

  • Page 131

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-17 knockouts provided on five surfaces surface mount using #10 pan head screws for hanging. (mount with vent holes facing up.) flush mount using #10 pan he...

  • Page 132

    Installing options and accessories eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-18 this page intentionally left blank..

  • Page 133

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-19 section ii operation.

  • Page 134

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 5-20

  • Page 135

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-1 chapter 6 understanding ups operation 6.1 ups system overview the eaton 9395 ups is a continuous-duty, solid‐state, transformerless (at 480 vac), three-phase, true online system that provi...

  • Page 136

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-2 the emergency bypass consists of either a momentary static switch and wraparound bypass breaker or a continuous static switch, and a backfeed protection contact...

  • Page 137

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-3 6.2.2 online mode figure 6‐2 shows the path of electrical power through the ups system when the ups is operating in onlinemode. During normal ups operation, pow...

  • Page 138

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-4 if the utility ac power is interrupted or is out of specification, the ups automatically switches to battery mode to support the critical load without interrupt...

  • Page 139

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-5 when a upm is placed into vmms mode, the upm will stop gating the inverter and rectifier and keep the output contactor closed in order to maintain voltage match...

  • Page 140

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-6 static switch k5 rectifier inverter k1 k3 battery converter battery battery breaker main power flow trickle current energized de-energized closed open breakers ...

  • Page 141

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-7 static switch k5 rectifier inverter k1 k3 battery converter battery battery breaker main power flow trickle current energized de-energized closed open breakers ...

  • Page 142

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-8 6.3 single ups unit system oneline configurations the system oneline drawings in this section show the simplified internal structure of the ups, battery supply,...

  • Page 143

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-9 system type voltage ups model oneline drawing system type output input ups model oneline drawing figure 6‐20 on page 6-25 9395-825/650 9395-825/750 9395-825/825...

  • Page 144

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-10 input breaker (cb1) (optional) x-slot interface e1, e2, e3 e6, e7, e8, e12 48v battery shunt trip note callout letters a , b , c , and d map to table 3‐4 on pa...

  • Page 145

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-11 input breaker (cb1) (optional) x-slot interface e1, e2, e3 e6, e7, e8, e12 48v battery shunt trip note callout letters a , b , c , and d map to table 3‐5 on pa...

  • Page 146

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-12 input breaker (cb1) (optional) x-slot interface e1, e2, e3 e6, e7, e8, e12 48v battery shunt trip note callout letters a , b , c , and d map to table 3‐4 on pa...

  • Page 147

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-13 input breaker (cb1) (optional) e1, e2, e3 e6, e7, e8, e12 note callout letters a , b , c , and d map to table 3‐5 on page 3-15. Note if the load requires a neu...

  • Page 148

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-14 input breaker (cb1) (optional) x-slot interface e1, e2, e3 e6, e7, e8, e12 48v battery shunt trip note callout letters a , b , c , and d map to table 3‐4 on pa...

  • Page 149

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-15 input breaker (cb1) (optional) x-slot interface e1, e2, e3 e6, e7, e8, e12 48v battery shunt trip note callout letters a , b , c , and d map to table 3‐5 on pa...

  • Page 150

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-16 input breaker (cb1) (optional) x-slot interface e1, e2, e3 e6, e7, e8, e12 48v battery shunt trip note callout letters a , b , c , and d map to table 3‐4 on pa...

  • Page 151

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-17 input breaker (cb1) (optional) e1, e2, e3 e6, e7, e8, e12 note callout letters a , b , c , and d map to table 3‐5 on page 3-15. Note if the load requires a neu...

  • Page 152

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-18 input breaker (cb1) (optional) x-slot interface e1, e2, e3 e6, e7, e8, e12 48v battery shunt trip note callout letters a , b , c , and d map to table 3‐6 on pa...

  • Page 153

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-19 input breaker (cb1) (optional) x-slot interface e1, e2, e3 e6, e7, e8, e12 48v battery shunt trip note callout letters a , b , c , and d map to table 3‐7 on pa...

  • Page 154

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-20 input breaker (cb1) (optional) x-slot interface e1, e2, e3 e6, e7, e8, e12 48v battery shunt trip note callout letters a , b , c , and d map to table 3‐4 on pa...

  • Page 155

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-21 input breaker (cb1) (optional) e1, e2, e3 e6, e7, e8, e12 note callout letters a , b , c , and d map to table 3‐5 on page 3-15. Note if the load requires a neu...

  • Page 156

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-22 input breaker (cb1) (optional) x-slot interface e1, e2, e3 48v battery shunt trip note callout letters a , c , and d map to table 3‐4 on page 3-14. Note if the...

  • Page 157

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-23 input breaker (cb1) (optional) x-slot interface e1, e2, e3 48v battery shunt trip note callout letters a , c , and d map to table 3‐5 on page 3-15. Note if the...

  • Page 158

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-24 input breaker (cb1) (optional) x-slot interface e1, e2, e3 48v battery shunt trip note callout letters a , c , and d map to table 3‐4 on page 3-14. Note if the...

  • Page 159

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-25 input breaker (cb1) (optional) e1, e2, e3 note callout letters a , c , and d map to table 3‐5 on page 3-15. Note if the load requires a neutral, a bypass sourc...

  • Page 160

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-26 e1, e2, e3 e6, e7, e8, e12 note callout letter a maps to table 3‐8 on page 3-18. Callout letters b , c , and d map to table 3‐5 on page 3-15. Note if the load ...

  • Page 161

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-27 note callout letter a maps to table 3‐8 on page 3-18. Callout letters b , c , and d map to table 3‐5 on page 3-15. Note if the load requires a neutral, a bypas...

  • Page 162

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-28 e1, e2, e3 e6, e7, e8, e12 note callout letter a maps to table 3‐8 on page 3-18. Callout letters b , c , and d map to table 3‐5 on page 3-15. Note if the load ...

  • Page 163

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-29 note callout letter a maps to table 3‐8 on page 3-18. Callout letters b , c , and d map to table 3‐5 on page 3-15. Note if the load requires a neutral, a bypas...

  • Page 164

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-30 e1, e2, e3 e6, e7, e8, e12 note callout letter a maps to table 3‐8 on page 3-18. Callout letters b , c , and d map to table 3‐7 on page 3-17. Note if the load ...

  • Page 165

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-31 note callout letter a maps to table 3‐8 on page 3-18. Callout letters b , c , and d map to table 3‐5 on page 3-15. Note if the load requires a neutral, a bypas...

  • Page 166

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-32 e1, e2, e3 note callout letter a maps to table 3‐8 on page 3-18. Callout letters c and d map to table 3‐5 on page 3-15. Note if the load requires a neutral, a ...

  • Page 167

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-33 note callout letter a maps to table 3‐8 on page 3-18. Callout letters c and d map to table 3‐5 on page 3-15. Note if the load requires a neutral, a bypass sour...

  • Page 168

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-34 maintenance bypass panel output from ups mis to ups rectifier input rib: rectifier input breaker bib: bypass input breaker mis: maintenance isolation breaker m...

  • Page 169

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-35 6.4 multiple ups distributed bypass system distributed bypass parallel operation extends the normal operation of eaton 9395 upss by offering increased capacity...

  • Page 170

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-36 s in vmms mode, the ups operates as a traditional double-conversion ups, but selectively shifts the load to fewer upms to increase the efficiency of the ups. I...

  • Page 171

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-37 main power flow ups 1 ups 2 ups 3 ups 4 output to critical load battery ups input tie cabinet ups 1 output bypass input ups 2 output ups 3 output ups 4 output ...

  • Page 172

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-38 main power flow ups 1 ups 2 ups 3 ups 4 output to critical load battery ups input tie cabinet ups 1 output bypass input ups 2 output ups 3 output ups 4 output ...

  • Page 173

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-39 6.4.4 battery mode – distributed bypass the upss transfer to battery mode automatically if a utility power outage occurs, or if the utility power does not conf...

  • Page 174

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-40 if at any time during the battery discharge the input power becomes available again, the rectifier begins to supply dc current to the inverter. At this point, ...

  • Page 175

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-41 battery breaker battery converter inverter k3 fuse rectifier k1 k2 fuse fuse fuse e6 e7 e8 e12 k5 static switch fuse cb4 e1 e2 e3 cb1 (optional) ups 1 a b tie ...

  • Page 176

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-42 battery breaker battery converter inverter k3 fuse rectifier k1 k2 fuse fuse fuse e6 e7 e8 e12 k5 static switch fuse cb4 e1 e2 e3 cb1 (optional) ups 1 a b tie ...

  • Page 177

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-43 battery breaker battery converter inverter k3 fuse rectifier k1 k2 fuse fuse fuse e6 e7 e8 e12 k5 static switch fuse cb4 e1 e2 e3 cb1 (optional) ups 1 a b tie ...

  • Page 178

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-44 battery breaker battery converter inverter k3 fuse rectifier k1 k2 fuse fuse fuse e6 e7 e8 e12 k5 static switch fuse e1 e2 e3 cb1 (optional) ups 1 a b tie cabi...

  • Page 179

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-45 battery breaker battery converter inverter k3 fuse rectifier k1 k2 fuse fuse fuse e6 e7 e8 e12 k5 static switch fuse e1 e2 e3 cb1 (optional) ups 1 a b tie cabi...

  • Page 180

    Understanding ups operation eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 6-46 battery breaker battery converter inverter k3 fuse rectifier k1 k2 fuse fuse fuse e6 e7 e8 e12 k5 static switch fuse e1 e2 e3 cb1 (optional) ups 1 a b tie cabi...

  • Page 181

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-1 chapter 7 ups operating instructions this section describes how to operate the ups. Note before starting the ups, ensure all installation tasks are complete and a preliminary startup has b...

  • Page 182

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-2 control panel isbm ac input breaker cb1 (optional) (not available with separate rectifier feed option) figure 7‐2. Ups controls and indicators – continuous stati...

  • Page 183

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-3 7.2 using the control panel the following paragraphs describe the ups control panel, including controls and indicators, and how to monitor ups operation. The con...

  • Page 184

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-4 7.2.1 status indicators the four symbols on the right side of the control panel are status indicators. These colored light emitting diode (led) lamps work with t...

  • Page 185

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-5 7.2.3 using the lcd and pushbuttons the lcd on the control panel provides an operator interface with the ups system. Figure 7‐4 identifies the display areas disc...

  • Page 186

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-6 7.2.4 using the menu the ups menu bar allows you to display data in the information area to help you monitor and control ups operation. Table 7‐2 shows the basic...

  • Page 187

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-7 7.2.6 display menu operation table 7‐3 describes the menu functions and and how to use them. Table 7‐3. Display menu operation function subfunction operation eve...

  • Page 188

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-8 table 7‐3. Display menu operation (continued) operation subfunction function contrast adjust select contrast from the system setup level 0 menu to display the co...

  • Page 189

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-9 table 7‐3. Display menu operation (continued) operation subfunction function high alert timer the high alert timer screen sets the length of time the all upms re...

  • Page 190

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-10 table 7‐3. Display menu operation (continued) operation subfunction function com port setup the com setup screen is used to change and save the settings for the...

  • Page 191

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-11 7.2.8 system status screen and controls press the controls pushbutton on the main menu bar to display the system status screen. Online operation, transfer to by...

  • Page 192

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-12 table 7‐5. Command menu operation function subfunction operation ups control commands use the up or down arrow pushbutton to highlight the command function desi...

  • Page 193

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-13 7.3 single ups operation note a field installed upm (fi-upm) is always designated as upm 4. 7.3.1 starting the ups in online mode to start the ups system: 1. Un...

  • Page 194

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-14 16. Verify the following messages display sequentially on the upm status line: dc starting, charger off inverter starting inverter syncing online, charging the ...

  • Page 195

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-15 7.3.3 disable energy saver system mode from the ups command menu to disable energy saver system mode: note the energy saver system mode commands are displayed o...

  • Page 196

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-16 7.3.5 enable variable module management system mode from the ups command menu to enable variable module management system mode: note the variable module managem...

  • Page 197

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-17 7.3.7 start variable module management system high alert mode from the ups command menu to start high alert mode: note the high alert mode commands are displaye...

  • Page 198

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-18 10. On the system status screen, select the bypass command. 11. Press the controls pushbutton on the system status menu bar. The bypass control command screen i...

  • Page 199

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-19 7.3.10 disable energy saver system mode from the bypass command menu to disable energy saver system mode: note the energy saver system mode commands are display...

  • Page 200

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-20 7.3.12 enable variable module management system mode from the bypass command menu to enable variable module management system mode: note the variable module man...

  • Page 201

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-21 5. Press the select pushbutton on the bypass command menu bar. If the ups is online, the ups transfers to battery mode and then to online mode in approximately ...

  • Page 202

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-22 9. On the system status screen, the ups status should indicate shutdown and the upm status should indicate offline. 10. Verify no alarms are active. 11. On the ...

  • Page 203

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-23 22. Verify the following messages display sequentially on the upm status line: dc starting, charger off inverter starting inverter syncing ready the upm 4 recti...

  • Page 204

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-24 17. To transfer the upm to online mode, press the controls pushbutton on the ups control command menu bar. The upm control command screen is displayed. 18. On t...

  • Page 205

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-25 the online status indicator is illuminated. The ups status indicates online. The upm status indicates online. 7.3.19 transfer from online to bypass mode and shu...

  • Page 206

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-26 3. On the ups control command screen, select the upm to shut down. 4. Press the controls pushbutton on the ups control command menu bar. The upm control command...

  • Page 207

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-27 7.3.22 ups and critical load shutdown to perform maintenance or service on the critical load, shut down power to the load: 1. Turn off all equipment that is bei...

  • Page 208

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-28 to use the load off pushbutton: 1. Press the load off pushbutton. The load off screen is displayed, providing a choice to proceed or abort the shutdown. C a u t...

  • Page 209

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-29 c a u t i o n do not attempt to restart the system after the load off until the cause of the shutdown has been identified and cleared. 7. To restart the ups aft...

  • Page 210

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-30 deactivated unlock pushbutton to release activated pushbutton locked into place figure 7‐8. Repo operation.

  • Page 211

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-31 7.4 multiple ups distributed bypass operation the paragraphs in this section provide operating instructions for a ups system containing multiple upss. Note a fi...

  • Page 212

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-32 17. Verify the following messages display sequentially on the ups status line: dc starting, charger off inverter starting inverter syncing online, charger on th...

  • Page 213

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-33 7.4.3 disable energy saver system mode from the ups command menu to disable energy saver system mode: note the energy saver system mode commands are displayed o...

  • Page 214

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-34 7.4.5 enable variable module management system mode from the ups command menu to enable variable module management system mode: note the variable module managem...

  • Page 215

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-35 7.4.7 start variable module management system high alert mode from the ups command menu to start high alert mode: note the high alert mode commands are displaye...

  • Page 216

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-36 10. On the system status screen, verify the ups status is shutdown and the upm status is shutdown. 11. On the system status screen, select the bypass command. 1...

  • Page 217

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-37 7.4.10 disable energy saver system mode from the bypass command menu to disable energy saver system mode: note the energy saver system mode commands are display...

  • Page 218

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-38 7.4.12 enable variable module management system mode from the bypass command menu to enable variable module management system mode: note the variable module man...

  • Page 219

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-39 5. Press the select pushbutton on the bypass command menu bar. If the ups is online, the ups transfers to battery mode and then to online mode in approximately ...

  • Page 220

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-40 9. On the system status screen, verify the ups status is shutdown and the upm status is offline. 10. Verify no alarms are active. 11. On the system status scree...

  • Page 221

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-41 21. If the ups is a plus 1 model or an upgraded 825/550, repeat steps 12 through 15 selecting upm 4 to start upm 4. 22. Verify the following messages display se...

  • Page 222

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-42 16. Verify the following messages display sequentially on the upm status line: dc starting, charger off inverter starting inverter syncing ready the upm rectifi...

  • Page 223

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-43 3. On the system status screen, select the ups command. 4. Press the controls pushbutton on the system status menu bar. The ups control command screen is displa...

  • Page 224

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-44 w a r n i n g power is present inside the ups cabinet. 7.4.20 single upm shutdown to shut down a single upm: 1. Press the controls pushbutton on the main menu b...

  • Page 225

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-45 7. Verify the following messages display sequentially on the upm status line: dc starting, charger off inverter starting inverter syncing ready the upm rectifie...

  • Page 226

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-46 w a r n i n g power is present inside the ups cabinet until the upstream input feeder circuit breaker is opened. Note if the ups contains an input breaker (cb1)...

  • Page 227

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-47 13. If the ups is a three upm model, repeat steps 8 through 11 selecting upm 3 to shut down upm 3. 14. If the ups is a plus 1 model or an upgraded 825/550, repe...

  • Page 228

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-48 13. Press the controls pushbutton on the system status menu bar. The ups control command screen is displayed. 14. On the ups control command screen, select go t...

  • Page 229

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-49 4. On the charger control command screen, select charger on . 5. Press the select pushbutton on the charger command menu bar. To turn the battery charger off: 1...

  • Page 230

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-50 w a r n i n g power is present inside the ups cabinet until the upstream input feeder circuit breaker is opened. To use the load off command: 1. Press the contr...

  • Page 231

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-51 7.4.28 using the remote emergency power-off switch a ups emergency power-off is initiated by the repo pushbutton switch. In an emergency, you can use this switc...

  • Page 232

    Ups operating instructions eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 7-52 this page intentionally left blank..

  • Page 233

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 8-1 chapter 8 communication this chapter describes the communication features of the eaton 9395 ups and provides information about connecting hardware and using terminal mode. For terminal wir...

  • Page 234

    Communication eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 8-2 lan and telephone drops for use with x-slot connectivity cards must be supplied by facility planners or the customer. For installation and setup of an x-slot card, contact an...

  • Page 235

    Communication eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 8-3 the enotify service relies on a connectups-x web/snmp card (or power xpert gateway card ) installed with the ups sending one-way status and event e-mails to eaton remote moni...

  • Page 236

    Communication eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 8-4 remote notification differs from the basic terminal mode with the addition of the following functions: s call answer the call answer function allows the user to call into the...

  • Page 237

    Communication eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 8-5 8.5.2 event history log this key sequence prints the entire event history log of the ups at the time the data is requested. The printout begins with the oldest alarm entry in...

  • Page 238

    Communication eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 8-6 model: eaton 9395 cto: tf12710000000 serial: mcu dsp: 70.81.14 mcu bootloader: 80.40 mcu pld: 1.00 pmf 1 dsp: 80.81.14 pmf 1 bootloader: 80.40 pmf 1 pld: 1.00 xslot can bridg...

  • Page 239

    Communication eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 8-7 8.6 building alarm monitoring this standard feature lets you connect the ups to your building alarms, such as smoke detectors or overtemperature alarms. The customer interfac...

  • Page 240

    Communication eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 8-8 the rmp ii contains a local horn and the backlit status indicators listed in table 8‐1. Table 8‐1. Rmp ii status indicators system normal the ups is energized (either with ut...

  • Page 241

    Communication eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 8-9 8.9 relay interface module ii an optional relay interface module ii (rim ii) uses relay contact closures to indicate the operating status and alarm condition of the ups syste...

  • Page 242

    Communication eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 8-10 8.10 supervisory contact module ii an optional supervisory contact module ii (scm ii) establishes an interface between the ups system and the customer's monitor. This interf...

  • Page 243

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 9-1 chapter 9 ups maintenance the components inside the ups cabinet are secured to a sturdy metal frame. All repairable parts and assemblies are located for easy removal, with very little disa...

  • Page 244

    Ups maintenance eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 9-2 s do not dispose of batteries in a fire. Batteries may explode when exposed to flame. S do not open or mutilate batteries. Released electrolyte is harmful to the skin and e...

  • Page 245

    Ups maintenance eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 9-3 a. Remove one top screw and two bottom screws securing each upm section front panel (see figure 4‐3 on page 4-4). Lift each panel straight up to remove it from the panel ha...

  • Page 246

    Ups maintenance eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 9-4 bottom left isbm air filters bottom right isbm air filters middle right isbm air filter figure 9‐2. Isbm section air filter locations – continuous static switch.

  • Page 247

    Ups maintenance eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 9-5 upm air filters figure 9‐3. Two upm section air filter locations.

  • Page 248

    Ups maintenance eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 9-6 upm air filters figure 9‐4. Three upm section air filter locations 3. If the ups is a plus 1 or a two upm model, check the field installed upm (fi-upm) air filter (located ...

  • Page 249

    Ups maintenance eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 9-7 fi-upm air filter figure 9‐5. Fi-upm air filter location 9.2.3 periodic maintenance periodic inspections of the ups should be made to determine if components, wiring, and c...

  • Page 250

    Ups maintenance eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 9-8 9.3 installing batteries note there is no manual dc disconnect device within the ups. Install batteries in accordance with the battery and battery system manufacturer's ins...

  • Page 251

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 10-1 chapter 10 product specifications 10.1 model numbers the ups is housed in a free‐standing cabinet, divided into two sections with safety shields behind the door and front panels. The ups ...

  • Page 252

    Product specifications eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality 10-2 10.2.2 ups output ups output capacity 100% rated current output voltage regulation "1% (10% to 100% load) output voltage adjustment (nominal +/–3%) 400 vac nominal,...

  • Page 253

    Eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality w-1 warranty limited factory warranty for three‐phase eaton ® ups products warrantor: the warrantor for the limited warranties set forth herein is eaton corporation, an ohio corporation (“eato...

  • Page 254

    Warranty eaton 9395 ups (450–825 kva) installation and operation manual s 164201725 rev 4 www.Eaton.Com/powerquality w-2.

  • Page 256

    *1642017254* 164201725 4.