FAAC B680H Manual - page 6
5
ENGLISH
9. REVERSING THE OPENING DIRECTION
Theopeningdirectionofthebarrierisusuallydeterminedatthetime
ofinstallationwiththeinstallationofthespringguide,thespringand
thepreloadadjustmentringnutonthepistonlocatedonthebeam
downward travel side.
Shoulditbenecessarytochangetheopeningdirection,proceedas
follows:
•
Releasetheoperator,asshowninparagraph6,andplacethe
beaminverticalposition,thenlocktheoperatoragain.
•
RemovethebeamasshowninFig.17.
•
Removethedevicesecuringtheplungingpistontotherocker
arm,asshowninFig.13.
•
Loosen the pre-load ring nut completely, remove it and then
remove the balancing spring and spring guide, reversing the
orderdescribedinparagraph4.4andinFig.14regardingthe
mechanicalinstallationoftheautomatedsystem.
•
Refittheplungingpistoninthecorrectfixinghole.
•
Proceedtoremovethefixingscrewonthepistonontheopposite
side.
•
Releasetheautomatedsystem,turntherockerarm90°andre-
insert,inorder,thespringguide,thebalancingspringandthe
theringnutintheplungingpistoninstalledonthenewclosing
side,accordingtotheorderdescribedinFig.14.Oncethisis
done,refittheplungingpistonontherockerarm.
•
ReinstallthebarfollowingtheinstructionsinFig.17.
•
Balancethesystemonceagainfollowingtheproceduredescribed
inparagraphs4.5and4.6.
•
Lock the operator once again following the instructions in
paragraph7
•
Reverse the motor cable connection as shown in point
d
of Fig. 14
10. ACCESSORIES
10.1 Installing a photocell
Thebarrierisequippedwithalateralcoveringprofile(fittedinthe
compartmentopening)underwhichthereareholesforcontaining
Safebeam,BUSorwirelessphotocells.
Toinstallthephotocells,proceedasfollows:
1. Remove the barrier compartment.
2. Match the holes on the barrier compartment with the holes on
thecorrespondingaluminiumcoveringprofileonthephotocell
installation side; ref. a isusedtofixthedevice,ref.bisused
forthepassageoftheitspowercable.Determinetheholesize
accordingtothesizeofthecablesandofthefixingscrewsused.
3. Connectthephotocellfollowingtheprovideddiagram.
4. Fixthephotocelltothelateralprofile,asshowninFig.22.
10.2 Installing the bar light kit
InstallationofanLEDbarlightkitincreasesvisibilityofthebar.
ProceedtoinstallfollowingtheinstructionscontainedinFig.31and
securingtheconnectioncableaccordingtothepathshown,usingthe
openingsforinsertingthetiestraps,locatedontheupright.
ConnectthekittooutputOut4ontheelectronicboardandconfigure
itaccordingtotheavailableswitchingonmodes(refertothesection
regardingtheelectronicboard,paragraph6onpage12).
Ensure that the two connector jacks are actually in
contact with the conductors inside the cord. Should
the bar lights still not turn on, reverse the connection
polarity.
10.3 Installation of a receiver antenna
Incaseareceiverantennashouldneedtobeattachedtothebarrier,
itcanbesecuredtotheflashingintegratedtrafficlightconnector(or
totheplasticbracket,iftheoptionalflashingtrafficlightconnector
shouldnothavebeeninstalled),asindicatedinthediagramsinFig.32.
11. REPAIRS
Forrepairs,contactanauthorisedFAACServiceCentre.