Gb instruction manual combi 740 oil-hydraulic operator for swinging gates below ground version with two-way locking device version with brake in open/close cycles version with 110 ° and 175° shaft rotation.
2 pic. 1 cutaway general view rotor stator combi 740 ® electric motor hydraulic jack releasing device two-way locking valve assembly safety pressure valve “close” safety pressure valve “open” valve cover two-way locking valve assembly motor end part motor end part pump shaft motor base flange suctio...
3 jack assembly and movement system earth phase common phase cable connector oil reservoir plug oil reservoir end cap wire connectors hydraulic oil arnica a 15 by agip electrical cable right-hand jack end cap dampening adjustment elbow joint bearing toothed main shaft central block cover tie rod 2 n...
4 pic. 2 instructions for the installation of combi 740, electro-hydraulic, below ground, all-in-one, with anti-crush system. Pic. 3 pre-arrangements are possible in the case that the mechanism is installed at a later stage after mounting the gate and finishing the pavement. You will have to set the...
5 pic. 6 pic. 7 pic. 4 pic. 5 combi 740 45 description ferrule with square hole shaft fitting collar welded to the gate fixing plate emergency locking shoe complete with collar and release spanner distance a 30 mm 42 mm 70 mm item no. 702/5 746 748 125 distance 0,00 40 100 200 350 500 220 ® brickwor...
6 pic. 8 pic. 10 pic. 9 sb sb pic. 11 ® once the concrete has set, put the combined unit in the enclosure and screw it down by means of the two long bolts supplied with the equipment, see picture no. 10. Attention: follow the wiring and connecting procedure on page 9 and picture 18. Allow the operat...
7 pic. 13 valve cover thrust adjustment: do this operation with both units more thrust/pushing power less thrust/pushing power red red blue yellow/green hydraulic release - lever s to release the unit turn the lever s which is fitted on the hydraulic motor pump left-handed red red blue yellow/green ...
8 pic. 17 pic. 16 pic. 15 dip-switch b now commence the electrical work. Connect the control panel elpro 13 exp as per pictures 16 and 18. Important: should n.C. Contacts eg. Photocells, stop button and safety contact not exist, link out individually. If the operators run in wrong direction reverse ...
9 pic. 19 pic. 18 1643 drwg. No. 13 exp gb ® electrical wiring diagram of the electronic programmer once the connections have been made, do the first switching test through the control panel. Set the motor run timer so that the motor is allowed to run 4 - 5 seconds more than the gates. Set the other...
Fixed connection connection two moves to position three. This should reverse gate operation 230 v 50 hz condenser 12,5 +f red yellow/green blue red connect the enclosure earth wire 2 1 3 10 pic. 21 pic. 20 special versions flow regulators for combi 740 ® manual test for combi 740 adjustment screw fl...
11 combi 740 technical specifications pic. 22 via mantova, 177/a - 37053 cerea (vr) italy - tel. 0442 330422 r.A. - fax 0442 331054 ® s.N.C. ® a 140 140 470 235 235 300 45 35 ø 12 190 b 190 50 10 40 50 35 30 c ® a the combined motor and jack of the combi 740 employs the latest technology with a quie...
13 cei l’apricancello combi 740 04-2007 the manufacturers reserve the right to change the products without any previous notice distributor’s box automatic gate manufacturers via mantova, 177/a - 37053 cerea (verona) italy tel. 0442 330422 r.A. - fax 0442 331054 e-mail: info@fadini.Net - www.Fadini.N...
