Fadini COMBI 740 Instruction Manual - Product Features
13
CEI
l’apricancello
COMBI 740
04-2007
The manufacturers reserve the right to change the products without any previous notice
Distributor’s box
AUTOMATIC GATE MANUFACTURERS
Via Mantova, 177/A - 37053 Cerea (Verona) Italy
Tel. 0442 330422 r.a. - Fax 0442 331054
e-mail: info@fadini.net - www.fadini.net
s.n.c.
®
PRODUCT FEATURES
• Pre-oiled and pre-set for immediate installation.
• Close proximity of pump and jack gives fast response.
• Close pivot point (45 mm) to gate pier.
• Manual release from inside and outside of property.
• Choice of 110
° or 175° rotation angle.
• Braking or non-braking versions available.
• Locking or non-locking versions available.
• Conforming to EN 12453, EN 12445 safety standards.
• All-in-one pump and jack unit, contained in a single enclosure, is
sunk into the ground at the foot of the left-hand and right-hand
gate to achieve synchronised operation. The unit should be piped
into a soak-away to allow for water drainage.
WARNINGS
- Before installing the equipment carry out a Risk
Analysis and fit any required device in compliance
with EN 12445 and EN 12453 Safety Norms.
- Should the combined unit jack/hydraulic motor pump
be removed for maintenance, servicing or repair,
disconnect the electric motor cable from the junction
box.
- Never cut off the cable from the electric motor.
- Make sure that the oil plug is properly tightened.
- Do not throw away oil from repaired or serviced units,
waste oil must be disposed of properly through a
specialised company.
- Do not throw away packaging such as cardboard,
polystyrene and nylon, which must be disposed of
properly through a specialised company.
- The electrical equipment must be properly earthed.
* Best performance can only be achieved by keeping to these
instructions.
The growth of MECCANICA FADINI has always been based
on the development of guaranteed products thanks to our
“TOTAL QUALITY CONTROL” system which ensures constant
quality standards, updated knowledge of the European
Standards and compliance with their requirements, in view
of an ever increasing process of improvement.
Meccanica Fadini recommends the control panel ELPRO 13 CEI to
achieve an installation that is in conformity to the existing safety
standards as illustrated in our chart.
The electronic programmer ELPRO 13 incorporates and can provide
all the functions which are required by the most demanding
applications with swinging gates.
In addition to the standard features of ELPRO 9 (Drwg. No. 1310) the
following requirements can be provided: “stroke reversing pulse”,
pedestrian mode, stop in any gate position by holding down the
remote control button. Among the added features and improvements
of ELPRO 13 in conformity to the European safety standards, there
is the mains rotary switch: it is fitted to the box cover and switches
off the mains voltage whenever the cover is removed.
The “CE” mark certifies that the operator conforms to the essential
requirements of the European Directive art. 10 EEC 73/23, in relation
to the manufacturer’s declaration for the supplied items, in
compliance with the body of the regulations ISO 9000=UNI EN 29000.
Automation in conformity to EN 12453, EN 12445 safety standard.
CHECKING AND MAINTENANCE:
To achieve an optimum performance and longer life of the
equipment and in observance of the safety regulations, it
is recommended that inspections and proper maintenance
are made by qualified technicians to the whole installation
ie. both the mechanical and electronic parts, as well as
wiring.
- Mechanical parts: maintenance every 6 months approx.
- Electronic apparatus and safety equipment: maintenance
inspection monthly.
EUROPEAN MARK CERTIFYING CONFORMITY
TO THE ESSENTIAL REQUIREMENTS OF THE
STANDARDS 98/37/EC
• DECLARATION OF CONFORMITY
• SAFETY NORMS
• EN 12453, EN 12445 STANDARDS
• CEI EN 60204-1 STANDARDS
• WARRANTY CERTIFICATE ON THE CUSTOMER’S REQUEST
SINGLE-PHASE
CUT OFF MAINS SWITCH