Falcon 1092 Deluxe Dual Fuel User's Manual & Installation And Servicing Instructions - page 29
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
29
Servicing
1 Servicing
When servicing or replacing gas carrying components,
disconnect from the gas supply before commencing
operation.
Check the appliance is gas sound after completion of
service. When checking for gas leaks do not use washing
up liquid - this can corrode. Use a product specifically
manufactured for leak detection.
Do not use re-conditioned or unauthorised gas controls.
Disconnect from the electricity supply before
commencing servicing, particularly before removing any
of the following: - control panel, side panels, hotplate
tray or any electrical components or covers.
Before electrical re-connection, check that the appliance
is electrically safe.
Note - References to LH and RH oven apply as viewed
from the front.
BEFORE SERVICING ANY GAS CARRYING COMPONENTS.
TURN OFF THE GAS SUPPLY.
2
To Remove the Hotplate
Disconnect the appliance from the electricity supply. Pull
the unit forward to gain access.
a) Remove the pan supports/hotplate accessories and
burner caps.
b) Remove the brass venturi in the centre of each
hotplate burner bezel.
c) Remove the bezel from the hotplate and disconnect
the spark ignition lead from the spark electrode.
d) Lift the hotplate clear of the appliance.
e) Replace in reverse order.
3
To Remove the Control Panel
Disconnect the appliance from the electricity supply.
a) Remove the pan supports/hotplate accessories and
burner caps.
b) Slacken the brass venturi at the centre of each burner.
c) Remove the control knobs from all taps.
d) Open the grill and RH oven doors. Remove 3 fixings
on the top front and 3 fixings on the control panel
underside.
e) Pull the control panel forward. Remove the
connections from the rear of the three neons.
Disconnect the earth lead and lift the panel clear of
the unit.
f) Replace all parts in reverse order.
g) When replacing any electrical connections refer to the
wiring diagram.
4
To Remove an Outer Side Panel
Disconnect the appliance from the electricity supply.
a) Remove the control panel as detailed in Section 3
b) Remove the retaining screw on the upper front edge
and the two fixings on the rear or the side panel. Undo
the lower retaining screw situated below the edge at
the panel front corner.
c) Remove the panel by pulling it away from the unit.
Should difficulty be encountered, it may be necessary
to slacken the two closest burners and both brass
venturi as detailed in Section 2.
d) Replace parts in reverse order. Ensure that both
venturis are fully tightened.
5
To Remove an Oven or Grill Neon
Disconnect the appliance from the electricity supply.
a) Remove the control panel as detailed in Section 3
b) Remove the relevant neon connection and undo the
nut which secures the neon to the control panel.
c) Replace parts in reverse order. Ensure the replacement
neon functions correctly.
6
To Remove a Thermostat
Disconnect the appliance from the electricity supply.
a) Remove the hotplate as detailed in Section 2.
b) Remove the control panel as detailed in Section 3
c) Open the appropriate oven door and remove the oven
shelves.
d) Pull the unit forward to gain access to the cover box.
Undo the cover screws and lift clear.
RH oven
Remove the two fixings that secure the thermostat
phial cover. Unclip the thermostat phial from the clips
in the oven back panel.
LH oven
Remove the two screws holding the thermostat phial
to the oven fan cover at the rear of the oven. Pull the
unit forward to access the rear of the cooker. Remove
the both cover boxes by removing the fixing screws
and lifting clear. Feed the thermostat capillary clear of
the oven.
d) Disconnect the wires from the thermostat and undo
the two fixings which secure the control to the
mounting plate.
e) Fit the replacement and re-assemble in reverse order.
Ensure that the phial is clipped to the oven rear,
positioned centrally between the clips. Check that the
thermostat functions correctly.
7
To Replace a Grill Controller
Disconnect the appliance from the electricity supply.
a) Remove the hotplate as detailed in Section 2.
b) Remove the control panel as detailed in Section 3.
c) Disconnect the controller wiring. Undo the fixings that
secure the device to the mounting plate.
d) Fit the replacement and re-assemble parts in reverse
order. Check that the replacement functions correctly.
8
To Remove an Oven Cut-Off Thermostat
Disconnect the appliance from the electricity supply.
a) Pull the unit forward to gain access to the cover box.
Undo the cover screws and lift clear.
b) The control is located on the earth plate beside the
oven element connections.