Farfisa PL10G User Manual - page 17
Mi 2466
Polski
English
- 17 -
Bezpoœrednie programowanie karty SIM
Kontakty
Nazwa Numer Opis
SL
3
Dostêp do urz¹dzenia maj¹ numery
zapisane w parametrze TN1, TN2 i TN3.
SMS
SIM
Zdalne programowanie przez SMS
;SL=3;
Przyk³ad:
Programowanie SL
6.3 SECURITY LEVEL SL=x
SL=x parameter, where "x" ranges from 0 to 5, defines
which administrator telephone number stored in the contacts
from TN1÷TN5 can enter into programming and remote
controlling of the
device; for programming refer to
the following table:
6.3 POZIOM BEZPIECZEÑSTWA SL-x
Parametr SL=x gdzie „x” przyjmuje wartoœæ od 0 do 5, defi-
niuje który numer telefoniczny administratora zapisany
w kontaktach jako TN1
÷TN5 mo¿e programowaæ i zdalnie kon-
trolowaæ modu³ ;
Tabella 6. Parametr SL
x =
Opis
0 Wszystkie po³¹czenia i SMS (bez zabiezpieczenia)
1
Tylko numery zapisane w parametrze TN1
2
Numery zapisane w parametrze TN1 i TN2
3
Numery zapisane w parametrze TN1, TN2 i TN3
4 Numery zapisane w parametrze TN1, TN2, TN3
i TN4
5 Numery zapisane w parametrze TN1, TN2, TN3
TN4 i TN5.
Uwaga.
Jeœli ustawiono 0 dostêp do modu³u
jest mo¿liwy z ka¿dego telefonu!
WA¯NE
Jeœli parametr SL nie zosta³ skonfigurowany urz¹dzenie akce-
ptuje wszystkie po³¹czenie. Zdalne programowanie przez wia-
domoœci SMS i zdalna kontrola jest mo¿liwa z ka¿dego telefo-
nu! Zaleca siê zmianê tego parametru.
Direct programming on the SIM card
Contacts
Name Number Description
SL
3
Numbers stored under parameters TN1,
TN2 and TN3 have access to unit
SMS
SIM
Remote programming by SMS
;SL=3;
Example:
SL programming
Table 6. SL parameter
x =
Description
0
Device access all calls and SMS.
1
Only the number stored under parameter TN1
has access to unit.
2
Numbers stored under parameters TN1 and TN2
have access to unit.
3
Numbers stored under parameters TN1, TN2 and
TN3 have access to unit.
4
Numbers stored under parameters TN1, TN2,
TN3 and TN4 have access to unit.
5
Numbers stored under parameters TN1, TN2,
TN3, TN4 and TN5 have access to unit.
Note.
If SL is set to 0, the access to the
device is possible from any phone!
IMPORTANT
If SL parameter is not programmed the device can accept
ALL CALLS. Remote SMS programming and remote
controlling is possible from any phone!
Mi 2466
Polski
English
- 20 -
6.5
PARAMETRY SYSTEMU
Aby zwiêkszyæ uniwersalnoœæ zastosowania modu³u
stosowane s¹ ró¿ne parametry.
6.5.1 Parametr HTN=x
HTN=x (x=0 lub 1) jest parametrem u¿ywanym do ukrycia
numeru dzwoni¹cego dla modu³u
:
HTN
= 0 identyfikacja numeru modu³u wy³¹czona;
HTN
= 1 identyfikacja numeru modu³u w³¹czona.
Domyœlnie wartoœæ parametru wynosi „1" co oznacza ¿e
identyfikacja dzwoni¹cego modu³u mycom jest w³¹czona.
6.5.2 Parametr UDC=x
Parametr u¿ywany do synchronizacji zegara modu³u
z zegarem operatora GSM. U¿ytkownik musi
wprowadziæ tutaj numer telefonu karty SIM modu³u
.
6.5.3 Parametr RAN=x
Parametr wykorzystywany do opcji autoodpowiedzi modu³u
Wartoœæ „x” oznacza liczbê dzwonków (x=1÷20)
wymaganych aby modu³ odebra³ po³¹czenie przychodz¹ce.
Numer przychodz¹cy musi byæ zapisany w parametrach
TN1÷TN5 modu³u (patrz rozdzia³ 6.1.2.4)
6.5.4 Parametr TST=x
Modu³
mo¿e cyklicznie wysy³aæ wiadomoœæ teksto-
w¹ SMS (patrz rozdzia³ 6.1.2.2 parametr LN3); wartoœæ „x”
definiuje okres czasowy w godzinach (x=1÷240) po jakim
czasie wysy³any jest SMS testowy; Jeœli ustawiono wartoœæ
0 testowa wiadomoœæ SMS nie jest wysy³ana.
Przyk³ad:
Jeœli parametr TST zaprogramowano z wartoœci¹
12, numer zapisany w parametrze LN3 otrzymuje wiadomoϾ
testow¹ co 12 godzin.
6.5.5 Parametr MNF=x
Parametr MNF=x definiuje operatora GSM do którego zareje-
strowany jest modu³
, „x” jest kodem MCC/MNC
wybranego operatora
Parametr MNF prze³¹cza urz¹dzenie z automatycznego
szukania operatora GSM (x=0) do rêcznego wybrania ope-
ratora GSM (kod operatora x=MCC/MNC)
Przyk³ad:
Kody MCC/MNC dla Plus (PL) to 26001, T-mobile
(PL) -26002, Orange (PL) - 26003, Play (PL) - 26006. Inne
kody MCC/MNC mo¿na znaleŸæ na stronie www.mcc-mnc.com.
6.5.6 Parametr MIC=x
Parametr MIC=x (x=0 minimum
÷ 40 maksimum) umo¿liwia
zmianê czu³oœci mikrofonu.
6.5.7 Parametr SPK=x
Parametr SPK=x (x=0 minimum ÷ 20 maksimum) umo¿liwia
zmianê g³oœnoœci g³oœnika.
6.5.8 Parametr ARST=x
Parametr ARST=x (x=0÷9999) okreœla przedzia³ czasowy
w godzinach dla cyklicznego automatycznego restartu urz¹-
dzenia. Jeœli wprowadzono wartoœæ 0 funkcja automatycznego
restartu jest wy³¹czona.
6.5 SYSTEM PARAMETERS
Different parameters are used to support versatile
functionality of
.
6.5.1
HTN=x parameter
HTN=x (x=0 or 1) is a parameter used in order to hide the
telephone number of the calling
device.
HTN
= 0 the device doesn’t send its phone number;
HTN
= 1 the device sends its phone number.
The default value is set to “1” which means that the number
of the calling device is sent.
6.5.2
UDC=x parameter
Parameter is used to synchronize
clock to GSM
network clock. User must enter here the phone number of
the
SIM card.
6.5.3
RAN=x parameter
Parameter is used to provide support for auto-answer
options for
device. The value of "x" defines the
numbers of rings (x=1÷20) needed for
device to
answer the incoming calls. The incoming number must be
on the TN1÷TN5 list so that
device is answering.
6.5.4
TST=x parameter
device can send periodically an SMS test message
(see paragraph 6.1.2.2, LN3 parameter);
"x" value defines
the time interval in hours (x=1÷240) after which test SMS is
sent; if value 0 is stored SMS test messages are not sent.
Example
: if TST value is programmed to 12, the numbers
linked to “LN3” receives a test message every 12 hours.
6.5.5 MNF=x parameter
Parameter MNF=x fix the provider of GSM network to which
register
device, "x" is the MCC/MNC code of the
chosen provider.
Parameter MNF switches the device from automatic
searching for the GSM provider (x=0) to a fix GSM provider
(x=MCC/MNC provider code).
Example:
MCC/MNC codes for Vodafone (UK) is 23415, O2
(UK) is 23402, TIM (IT) is 22201 and Vodafone (IT) is 22210.
Other MCC/MNC codes can be found on www.mcc-
mnc.com.
6.5.6 MIC=x parameter
MIC=x parameter (x=0 min ÷ 40 max) enables to change the
sensitivity level of microphone.
6.5.7 SPK=x parameter
SPK=x parameter (x=0 min ÷ 20 max) enables to change the
sound level of loudspeaker.
6.5.8 ARST=x
ARST=x parameter (x=0÷9999) defines time interval, in
hours, for periodic auto-restart of
device. If value 0
is stored auto-restart is disabled.