Fiamma TURBO-VENT 160 Instructions For Use Manual - page 4
4
17
1) Marquer le point exact du trou d'ouverture et la dimension avec une règle et
une équerre.
2) Couper le carré marqué avec une scie électrique.
3) Ne pas oublier de préparer la connection électrique (seulement 12 Vdc, pas
220V).
4)Remplir les rainures sur la côté inférieure du cadre supérieur du lanterneau
avec du silicone.
5) Placer le cadre supérieur dans le trou faisant attention que les charnières
soient dans le sens de la marche du véhicule.
6) Fixer le cadre supérieur du lanterneau avec 20 vis autofiletantes.
7) Avant de connecter les fils de l'alimentation du moteur s'assurer que le
régulateur de vitesse soit en position "0".
8) Connecter les fils d'alimentation du moteur.
9) Fixer le cadre inférieur du lanterneau avec 8 vis autofiletantes.
1) Segnare con l'aiuto di un righello e una squadra la dimensione del foro ed il
punto esatto.
2) Con un seghetto elettrico tagliare il quadro.
3) Ricordare di predisporre il collegamento elettrico (solo 12 Vdc - NO 220V).
4)Siliconare bene la parte sottostante del telaio superiore seguendo gli appositi
binari.
5) Collocare il telaio superiore nel foro d'apertura, assicurandosi che le cerniere
siano rivolte nella direzione di marcia del mezzo.
6) Fissare il telaio superiore con 20 viti autofilettanti.
7) Prima di collegare i fili di alimentazione, assicurarsi che il regolatore di velocità
sia in posizione “0".
8) Collegare i fili dell'alimentazione motore.
9) Fissare il telaio inferiore con 8 viti autofilettanti.
INSTRUCTIONS DE MONTAGE
ISTRUZIONI DI MONTAGGIO
6
SILI
CON
E
4
5
38/4
0 c
m
38
/40
cm
1
+
+
--
+
+
--
+
-
12V
dc
3
2
Your Turbo-Vent 160 PANEL can be completed with the blind kit art. n. 98683-033.
Installation is simple; it is fitted to the inside of the Turbo-Vent 160 PANEL frame
with just 4 screws.
*
Ensure that the power supply has been disconnected before carrying out any kind of
operation, then reconnect.
Troubleshooting
The fan does not rotate after
turning on the deviator
IThe thermostat has been
positioned on the max.
temperature
IPower voltage is less
than 10 V
IThe fuse may be blown
IThe cables are incorrectly
connected
IForeign bodies are blocking
the blade
INone of the above causes
IMove the thermostat knob
IReplace or charge the
battery, check that the
voltage is 12 V
IReplace the fuse (5 A
delayed micro fuse)*
ICheck that connections
correspond to wiring
diagram*
IRemove any obstructions
from the blade*
IContact your Fiamma
Service Centre
The speed of the fan cannot
be varied
IThe cables are incorrectly
connected
ICheck that connections
correspond to wiring
diagram*
IDeviator in exhaust position ISet the deviator to
ventilation mode
The fan rotates but no air is
felt insidepas l'air à l'intérieur
IPower failure
IForeign bodies are blocking
the blade
IThe internal circuit fuse
may be blown
IThermostat has intervened
ICheck the fuses in the main
control panel*
IRemove any obstructions
from the blade*
IReplace the fuse (5A
delayed micro fuse)*
ILower the intervention point
of thermostat.
The fan stops on its own
Problem
Cause
Solution