Gaggia Syncrony Digital DM1075 User Manual - page 11
26
25
DISPOSAL
The machine must be descaled every 3-4 months,
according to the water hardness degree. A
more frequent descaling is recommended wher-
ever the water hardness degree is very high.
This machine is supplied with a particular
warning light
Descaling must be carried out at the latest when
this message is displayed. In spite of the mes-
sage, the machine does not stop working. To
switch off the display, press the steam key for
approx. 5 seconds until the message disap-
pears.
Furthermore, said display warning may be
adjusted according to the water hardness de-
gree. The machine has been adjusted at the
factory to 25º _H value, which causes the
display to switch on showing the message
DESCALING after approx 150 l.
The water hardness value may be changed, if
necessary, following the instructions shown on
page 27.
The following adjustments are possible:
Hardness 4:
high water hardness, over 29º
fH (14
°
dH), approx. 80 l water passage.
Hardness 3:
medium water hardness, approx.
20º-29º fH (7
°
-14
°
dH), approx. 150 l water
passage
Hardness 2:
soft water, approx. 12º-20º fH
(4
°
-7
°
dH), approx. 300 l water passage
Hardness 1:
less than 10º fH (3
°
dH),
approx. 500 l water passage
In case of hard water, a filter should be used
both to improve the coffee quality and to protect
the machine, thus reducing the descaling fre-
quency.
Note:
for this purpose, use a descaling prod-
uct suitable for coffee machines.
Never use
vinegar to clean the machine; it might
damage it.
There are two ways to carry out the descaling
of the machine:
Automatic descaling
Switch the machine onto the programming
mode (see page 33).
Move the asterisk at the end of the line to the
menu item DESCALING. To activate this menu
item press
ent
.
The display shows:
"DESCALING "
Pour a descaling solution into the water tank
(according to the instructions on the package).
Place a large container under the steam/hot
water dispensing tube and open the steam/hot
water knob slowly. The automatic descaling
starts. Small quantities of descaling solution are
pumped into the circuit. Then the pump stops to
let the solution take effect.
The display shows:
"MACHINE IS "
"DESCALING "
This operation takes about 45 minutes. As soon
as descaling is completed, the display shows:
"DESCALING "
"FINISHED "
and the pump stops.
Close the hot water knob and press
ent
. A
display message reminds you to rinse away
residue from the machine
"RINSE MACHINE "
Remove the water tank, rinse it and fill it with
water. Clean the machine using the hot water
knob and let the whole tank content flow out.
The display shows:
"RINSING FINISHED "
Close the hot water knob again and press
ent
.
The machine is in the main menu of the program-
ming mode. Move the asterisk at the end of the
line to using the key *Press
ent
. The
machine is now in the normal mode. After
heating, the machine is ready to work.
Note
Descaling can be interrupted any time by press-
ing
esc
. Before doing this, close the hot water
knob.
Standard descaling
Switch off the machine. Pour a descaling prod-
uct into the water tank (according to the instruc-
tions on the package). Place a large container
under the steam/hot water dispensing tube (7)
and open the steam/hot water knob (9) slowly,
turning it counterclockwise. Turn on the machine
by pressing the main switch and let the descaling
product flow out of the dispensing tube for
approx. 1 min.
Close the knob again. Turn off the machine with
the main switch and let the solution take effect
for approx. 5 minutes. Repeat this procedure
two or three times, to allow all the descaling
product in the water tank to flow out of the
dispensing tube.
As soon as decalcification has been carried
out, rinse the water tank (11) thoroughly and fill
it with water.
Switch on the machine again and let water
(approx. 2 l) flow out of the steam/hot water
dispensing tube in order to rinse away residue.
The coffee machine is now ready for operation.
Important
A periodic descaling avoids expensive repairs.
The machine warranty does not cover damages
occurring as a result of the non-observance of
descaling procedures, improper use and any
other instructions contained herein. Maintain
the manufacturer’s adjustment if the water hard-
ness degree is not known.
Storage of the machine
Switch off and unplug the machine if it will not
be used for long periods of time.
Keep the machine in a dry place, far from the
reach of children.
Should the machine not be used for a long
period, keep it from dust and dirty.
Maintenance
Periodically check the machine and clean it in
accordance to the instructions.
Disposal
Machines which are no longer operational
should immediately be made non serviceable,
by cutting the power cord. Machines should be
delivered to a public disposal centre.
Troubleshooting
In case of failure, fault or suspected damage
following a fall, unplug the machine immedi-
ately.
To fix problems, follow the instruc-
tions in the table below. Otherwise
contact authorised personnel.
CLEANING/MAINTENANCE