Galletti AREO 12 Technical Manual - Areo
22
AP66000265 - 03
All copying, even partial, of this manual is strictly forbidden
AREO
15
ACCESSORIES
KP - Power interface for connection of up to 4
units to a single control panel
The KP master sleeve can be installed to control
with a single control panel up to 4 units (connected
in parallel).
This accessory is designed for installation on a
DIN drive, usually placed on electric board.
CST -Delta/star selector for installation in electric panels
Allows the rotational speed switching (off / low-speed / high-speed).
It can be used only on 400 V (3-phase) models. For electrical box
installation.
CSTP - Delta/star selector with box for wall installation
Allows the rotational speed switching (off / low-speed / high-speed). It
can be used only on 400 V (3-phase) models. Supplied with plastic box
for wall installation.
TA - Wall mounted room thermostat
Automatic regulation of the the room temperature:
- only in the heating mode working on the fan motor
assembly;
- only in the cooling mode working on the fan motor
assembly;
- both in cooling and heating mode, with remote
mode selection working on the fan motor assembly.
TA2 - Wall mounted room thermostat with summer-
winter selector
Wall mounted room thermostat with cooling/heating
mode selector.
Automatic regulation of the room temperature both
in heating and cooling mode, working on the fan
motor assembly.
CSD - Wall mounted control panel for opening and
closing of the motor driven air intake louver PAEMM
Designed for wall installation, it allows the proportional
opening and closing from 0 to 100% of thePAE MM motor
driven fresh air intake louver.
PAE - Fresh air intake louver
Allows the fresh air intake from the outside. Usually
installed together with the outdoor fresh-air intake grill
(GR option)
PAE M - Manual mixing fresh air intakelouver
Allows the mixing of return and fresh air. The amount of
fresh air can be adjusted (manual louver) within the range
0-100%. The option is supplied with wall-supports and is
usually installed together with the outdoor fresh-air intake
grill (GR option)
0%
100%
50%
PAE MM - Motor-driven mixing air intake louver
Allows the mixing of return and fresh air. The amount of
fresh air can be adjusted (motorized louver) within the
range 0-100%. The proportional drive motor (24 V power
supply, voltage transformer included) is equipped with a
shaft-return spring that forces the louver to close (avoiding
the fresh air intake) in case of blackout. The drive motor
can be connected to external auxiliary contacts in order
to force the automatic opening and closing (air extractors, antifreeze
thermostats, etc…). The motor driven fresh air intake louver must be used
together with the dedicated control panel, for proportional opening-closing
(CSD option)
The option is supplied with wall-supports and is usually installed together
with the outdoor fresh-air intake grill (GR option)
GR - Outdoor air intake grille
Galvanised aluminium outdoor fresh-air intake grill.
Equipped with anti-intrusion grill, in order to avoid the
intrusion of dangerous objects from the outside.
DFP - wall mounting board
The DFP option (made in steel of adequate
thickness) allows the installation on indoor
walls. The fan heater is connected to the wall
mounting board by mean of the four tongues in
the back panel of the unit (connection screws
supplied).
DFC - column mounting board
The DFP option (made in steel of adequate
thickness) allows the installation on indoor
columns or walls . The fan heater is connected
to the wall mounting board by mean of the four
tongues in the back panel of the unit
(connection and option mounting screws
supplied).
DFO - Adjustable wall/column mounting
board
The DFO option (made in steel of adequate
thickness) allows to orient the fan heater as
needed (towards left or right), during the
installation on indoor columns or walls. The
fan heater is connected to the wall mounting
board by mean of the four brackets in the back
panel of the unit (connection and option
mounting screws supplied).
R - Protection grill for gymnasium
Protection grill for gymnasium (against ball
impact on adjustable louvers). Option mounting
screws supplied.
D0 -Additional row of louvers
The additional row of louvers air diffuser
allows to orient the air flow on the horizontal
plane, towards left or right. Option mounting
screws supplied.