Galletti AREO 12 Technical Manual - Areo
3
AP66000265 - 03
All copying, even partial, of this manual is strictly forbidden
AREO
2
UNIT DESCRIPTION
1
3
5
6
7
8
9
10
11
12
2
4
(1) Cabinet: side panel
(2) Cabinet: upper/lower panel
(3) Rear panel/fan compartment
(4) Finned block heat exchanger (heat exchanger coil)
(5) Safety grille (fan) supporting motor
(6) Adjustable louvers
(7) Auxiliary drip tray
(8) Main drip tray
(9) Top cover of heat exchanger
(10) Conveyor duct
(11) Wall/ceiling mounting brackets
(12) Plastic corner trim on cabinet (left and right)
3
CONSTRUCTIVE FEATURES
The AREO are mainly made of the components listed below.
Prepainted sheet steel cabinet complete with ABS corner trim, internally
insulated to prevent condensate from forming on the cabinet during operation
with chilled water.
The cabinet is complete with adjustable aluminium louvers (spring operated)
placed on the air outlet which allow an optimal distribution of the air within
the air conditioned room.
AREO is supplied with brackets for suspending the fan heater to the ceiling
or joining it to the mounting board for installation on the wall (accessory).
High conductivity heat exchanger made with copper tubes and aluminium
fins assuring higher heat exchange than standard iron tubes exchangers.
The heat exchanger is set back in relation to the air outlet; an auxiliary drip
tray is fitted into the front to guarantee complete collection of condensate.
Galvanised sheet steel drip tray insulated with closed cells polyurethane,
connected to the auxiliary tray.
All motors are standard equipped with:
- internal thermal protection (klixon)
- windings in class F
- protection degree IP55
Two Speeds, 4/6 poles or 6/8 poles, in the three - phase 400V version.
3 speeds in the single - phase 230V (1400, 900 e 700 rpm), available for
the complete range
Upon request, the following equipment is available
:
- Polarity different from standard ones (example 4/8 poles)
Axial fan with statically balanced sickle blades housed in a specially
designed compartment that enhances ventilation and reduces noise emissions.
Safety grille made of electrogalvanised steel wire: it supports the motor and
is fixed to the cabinet by means of vibration damping supports.
4
AVAILABLE OPTIONS
AREO is complete with a wide range of accessories as control panels usually associaded with fan coils, thanks to the use of 230V single-phase three speed
motors, a standard arrangement for all models and the operation system with chilled water.
230V SINGLE-PHASE CONTROL PANEL
CD
Flush mounted speed control panel
CDE
Wall mounted speed control panel
TD
Wall mounted speed control panel, electromechanical thermostat
and summer winter selector
TDC
Wall mounted speed control panel and electromechanical
thermostat
MCBE
Wall-mounted microprocessor control - GALLETTI model
MYCOMFORT BASE
MCME
Wall-mounted microprocessor control - GALLETTI model
MYCOMFORT MEDIUM
MCLE
Wall-mounted microprocessor control - GALLETTI model
MYCOMFORT LARGE
LED503
Recess wall-mounted microprocessor control
MCSWE
Water temperature electronic sensor for MYCOMFORT controls
DIST
MYCOMFORT controller spacer for wall mounting
KP
power interface for connecting up to 4 units to a single control
panels
400 V THREE-PHASE CONTROL PANEL
CST
delta/star selector for installation in electric panels
CSTP
delta/star selector with box for wall installation
ROOM THERMOSTAT
TA
electromechanical room thermostat
TA2
electromechanical room thermostat with summer winter selector
MOUNTING BOARDS
DFP
wall mounting board
DFC
column mounting board
DFO
adjustable wall/column mounting board
FRESH AIR INTAKE LOUVERS
PAE
fresh air intake louver
PAE M
manual mixing fresh air intake louver
PAE MM
motor driven mixing air intake louver, modulating motor, 24V
IP 54, with spring return
CSD
wall mounted control panel for opening and closing of the
motor driven air inteake louver PAEMM
GR
fresh air intake grille
AIR DIFFUSER
DO
Additional row of louvers
R
Protection grill for gymnasium (against ball impact)
LA
Air curtain diffuser