D betriebsanleitung elektro-kettensäge gb operating instructions electric chainsaw f mode dʼemploi tronçonneuse électrique nl instructies voor gebruik elektrische kettingzaag s bruksanvisning elektrisk motorsåg dk brugsanvisning elektrisk kædesav n bruksanvisning elektrisk kjedesag fin käyttöohje sä...
D wichtige information bitte vor dem benutzen des gerätes durchlesen und gut aufbewahren gb important information read before use and retain for future reference f renseignements importants a lire avant usage et à conserver pour référence ultérieure nl belangrijke informatie leest u deze informatie ...
25 26 23 24 27 28 8 a 5 19 7 gar dena Æ 2 3 4 1 6 16 12 17 10 20 13 18 15 14 11 9 21 22 29 5 4 7 8 2 3 1 6 12 10 13 11 9 29 30 31 32.
12 14 1 b 1 5 6a a 2 3 3a c b 2 a b 3b 4a 4b 6b 7a 7b c c.
D 1a 2a 3 5a 6a 1b 2b 4 5b 6b 7a 7b.
E 1 2 f g 3mm = 1 3 5 6 7 8 1 2 2 4a 4b.
9 10 11 12 13 14 15 0.5mm g a b 30 0 - 35 0 60 0
1 2 3 4 h.
3 2 5 6 7 8 9 10 c a c b b a c c b b h.
A. General description english - 1 1) guaranteed sound power according to directive 2000/14/ec 2) class ii tool 3) ce marking of conformity 4) rated frequency 5) rated power 6) alternating current 7) rated voltage 8) product code 9) year of manufacture 10) maximum length of guide bar 11) manufacture...
B. Safety precautions warning! Read the instruction manual carefully protective boots protective goggles or visor, protective helmet and hearing protection protective cut-proof gloves protective long, cut-proof trousers chain brake: deactivated, activated remove plug from the mains immediately if th...
F) if operating a power tool in a damp location is unavoidable, use a residual current device (rcd) protected supply. Use of an rcd reduces the risk of electric shock. 3) personal safety a) stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool...
Causes and operator prevention of kickback: kickback may occur when the nose or tip of the guide bar touches an object (fig b3) , or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a sudden reverse reaction, kicking the guide bar up and back towards ...
Electrical safety 1. It is recommended that you use a residual current device (r.C.D.) with a tripping current of not more than 30ma. Even with a r.C.D. Installed 100% safety cannot be guaranteed and safe working practice must be followed at all times. Check your r.C.D. Every time you use it. 2. Bef...
D. Assembly / disassembly bar and chain assembly take great care when assembling to ensure this is performed correctly. English - 6 e. Start-up and stopping start-up : grip both handles firmly, release the chain brake lever whilst ensuring hand is still on front handle, press and maintain the switch...
(fig.1) when using the machine, prevent: - cutting in conditions where the trunk could split during cutting (wood under pressure, dry dead trees, etc): sudden splitting can be very dangerous. - the bar or the chain from becoming blocked in the cutting notch: if this should occur, disconnect the mach...
English - 8 cutting action pushing the chain (from bottom to top) (fig.3) will lead to the danger of a sudden movement of the machine in the direction of the user, with the risk of hitting the user, or an impact of the “kickback danger zone” on the trunk resulting in strong kickback; extreme care mu...
Motor does motor turns the machine motor turns braking not start with difficulty starts but improperly or devices do or loses does not cut at reduced not stop the power properly speeds chain properly make sure the main line is powered make sure the machine is properly plugged in make sure your cable...
Eu certificate of conformity english - 10 the undersigned gardena manufacturing gmbh, hans-lorenser-str. 40, d-89079 ulm, hereby certifies that, when leaving our factory, the units indicated below are in accordance with the harmonised eu guidelines, eu standards of safety and product specific standa...
Deutschland / germany gardena manufacturing gmbh central service hans-lorenser-straße 40 d-89079 ulm produktfragen: (+49) 731 490-123 reparaturen: (+49) 731 490-290 service@gardena.Com argentina husqvarna argentina s.A. Vera 745 (c1414aoo) buenos aires phone: (+54) 11 4858-5000 diego.Poggi@ar.Husqva...
