- DL manuals
- Garmin
- Software
- GNS 530
- Installation Manual
Garmin GNS 530 Installation Manual
Summary of GNS 530
Page 1
(gns tm 530 shown) £ garmin international, inc. 190-00181-02, revision q november 2005 500 series installation manual gps 500 and gns tm 530/530a/taws gns is a trademark of garmin ltd. Or its subsidiaries and may not be used without the express permission of garmin..
Page 2
Page a 500 series installation manual rev q 190-00181-02 copyright 1998 - 2005 garmin ltd. Or its subsidiaries all rights reserved except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any pur...
Page 3
500 series installation manual page i 190-00181-02 rev q this manual reflects the operation of main software version 6.01. Some differences in operation may be observed when comparing the information in this manual to earlier or later software versions. Information subject to export control laws thi...
Page 4
Page ii 500 series installation manual rev q 190-00181-02 table of contents 1. General description 1.1 introduction .........................................................................................................................................1-1 1.2 equipment description.....................
Page 5
500 series installation manual page iii 190-00181-02 rev q list of figures figure 2-1. Gps antenna installation considerations .................................................................2-2 figure 3-1. Coaxial cable installation ....................................................................
Page 6
Page iv 500 series installation manual rev q 190-00181-02 500 series hardware mod level history the following table identifies hardware modification (mod) levels for the gps 500 and gns 530. Mod levels are listed with the associated service bulletin number, service bulletin date, and the purpose of ...
Page 7
500 series installation manual page 1-1 190-00181-02 rev q 1. General description 1.1 introduction this manual describes the physical, mechanical, and electrical characteristics and the installation requirements for the 500 series (gps 500 and gns 530) panel-mounted units. After installation of the ...
Page 8
Page 1-2 500 series installation manual rev q 190-00181-02 1.3 technical specifications the conditions and tests required for tso approval of this article are minimum performance standards. It is the responsibility of those installing this article either on or within a specific type or class of airc...
Page 9
500 series installation manual page 1-3 190-00181-02 rev q 1.3.3 gps specifications regulatory compliance tso c129a class a(1), rtca do-208, jtso c129a regulatory compliance (taws units only) etso c129a acquisition time a) search-the-sky (without almanac, without initial position or time): 5 minutes...
Page 10
Page 1-4 500 series installation manual rev q 190-00181-02 ** specifications shown apply at nominal input voltages of 13.75 vdc or 27.5 vdc, as applicable, and with a nominal 50 ohm resistive load at the antenna connector. 1.3.5 vor specifications (gns 530 only) regulatory compliance tso c40c, jtso-...
Page 11
500 series installation manual page 1-5 190-00181-02 rev q 1.3.6 loc specifications (gns 530 only) regulatory compliance tso c36e, jtso-c36e, rtca do-195 class a, eurocae ed-46b annex 10 volume i (radio navigation aids) par. 3.1.4 regulatory compliance (taws units only) etso-2c36f receiver audio sen...
Page 12
Page 1-6 500 series installation manual rev q 190-00181-02 1.3.7 glideslope specifications (gns 530 only) regulatory compliance tso c34e, jtso-c34e, rtca do-192, eurocae ed-47b regulatory compliance (taws units only) etso-2c34f sensitivity -87 dbm or less for 60% of standard deflection. Centering ac...
Page 13
500 series installation manual page 1-7 190-00181-02 rev q 1.4 tso limitations a limitation exists pertaining to tso-c36e (localizer) and tso-c34e (glideslope). The main board lateral deviation (j4001 pin 21 main +left and j4001 pin 22 main +right) and vertical deviation (j4001 pin 27 main +up and j...
Page 14
Page 1-8 500 series installation manual rev q 190-00181-02 the fde function is built into the gps 500/gns 530 and does not require pilot interaction. In contrast, the fde prediction program does require pilot interaction and must be used prior to oceanic/remote area flights to predict fde availabili...
Page 15
500 series installation manual page 2-1 190-00181-02 rev q 2. Installation 2.1 introduction careful planning and consideration of the suggestions in this section are required to achieve the desired performance and reliability from the 500 series unit. The guidance of faa advisory circulars ac 43.13-...
Page 16
Page 2-2 500 series installation manual rev q 190-00181-02 2.2.6 antenna limitations garmin’s ga 56 antennas are recommended for installations where the airspeed of the aircraft is subsonic. In such installations, ga 56—mod 1 or later—must be used. See the com, vor/loc, and glideslope antenna specif...
Page 17
500 series installation manual page 2-3 190-00181-02 rev q 2.3 rack considerations plan a location which gives the pilot complete and comfortable access to the entire keypad and which is plainly visible from the pilot’s perspective. Installation of remote switches and annunciators may not be require...
Page 18
Page 2-4 500 series installation manual rev q 190-00181-02 qualified gps antenna this antenna must be one of those listed in the accessories list, or meet the following requirements: 1. Do-160c environmental conditions the antenna shall meet the environmental conditions listed below and shall confor...
Page 19
500 series installation manual page 3-1 190-00181-02 rev q 3. Installation procedure 3.1 unit and accessories the gns 530 units are available under the following part numbers: 3.1.1 gns 530 catalog p/n unit p/n gns 530a taws accessories (1) color operating voltage minimum xmit pwr 010-00182-00 011-0...
Page 20
Page 3-2 500 series installation manual rev q 190-00181-02 note the connector kit 011-00351-0x includes a single 78-pin high-density d connector for p5001. The second 78-pin connector on the back of the 500 series unit (p5050) is used for installation of a remote taws annunciator (garmin p/n 013-000...
Page 21
500 series installation manual page 3-3 190-00181-02 rev q 3.1.5 optional accessories the following installation accessories are available: 1. Gps antenna options: x ga 56 antenna kit, without cable (mod 1 or later, garmin p/n 010-10040-01). X this kit contains the following items: item garmin p/n q...
Page 22
Page 3-4 500 series installation manual rev q 190-00181-02 3.2 data base options item garmin p/n data card, world wide 010-10201-00 data card, americas 010-10201-01 data card, international 010-10201-02 data card, terrain* 010-10201-20 *required for taws and terrain. 3.3 miscellaneous options item g...
Page 23
500 series installation manual page 3-5 190-00181-02 rev q 3.5 antenna installation for the com, vor/loc, and glideslope antennas, follow the manufacturers’ instructions. The remainder of this section applies to the gps antenna. The ga 56 antenna outline and footprint dimensions are shown in figure ...
Page 24
Page 3-6 500 series installation manual rev q 190-00181-02 3.6 cable installation 1. Route the coaxial cable to the rack location keeping in mind the recommendations of section 2. Secure the cable in accordance with good aviation practice. 2. Trim the coaxial cable to the desired length and install ...
Page 25
500 series installation manual page 3-7 190-00181-02 rev q table 3-2. Recommended crimp tools (or equivalent) connector type high density standard density wire gauge 22-24 awg 18 awg 20-24 awg hand crimping tool positioner insertion/ extraction tool positioner insertion/ extraction tool positioner i...
Page 26
Page 3-8 500 series installation manual rev q 190-00181-02 3.7 rack installation 1. The back plate of the rack may optionally be removed for ease of mounting in the aircraft panel. To do so, remove the two #4-40 screws, tilt the back plate away from the tray, and then slide the back plate to the sid...
Page 27
500 series installation manual page 4-1 190-00181-02 rev q 4. System interconnects 4.1 pin function list 4.1.1 p5001 view of j5001 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 ...
Page 28
Page 4-2 500 series installation manual rev q 190-00181-02 connector p5001, continued pin pin name i/o 37 altitude alarm audio hi (not implemented at time of publication) out 38 altitude alarm audio lo (not implemented at time of publication) out 39 lighting bus hi in 40 lighting bus lo in 41 gps rs...
Page 29
500 series installation manual page 4-3 190-00181-02 rev q 4.1.2 p5050 (with taws) view of j5050 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 6...
Page 30
Page 4-4 500 series installation manual rev q 190-00181-02 4.1.4 p5002 (gns 530 only) view of j5002 connector from back of unit 13 12 11 10 9 8 7 6 5 4 3 2 1 25 24 23 22 21 20 19 18 17 16 15 14 pin pin name i/o 1 reserved -- 2 reserved -- 3 reserved -- 4 com mic key in 5 intercom mic hi in 6 com mic...
Page 31
500 series installation manual page 4-5 190-00181-02 rev q 4.1.5 p5006 (gns 530 only) view of j5006 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 pin pin name i/o 1 vor/loc +to out 2 vor/loc +fro...
Page 32
Page 4-6 500 series installation manual rev q 190-00181-02 4.2 power, lighting, and antennas 4.2.1 power, lighting, and antennas function the section covers the power input requirements, lighting bus input, and antenna connections. 4.2.2 power, lighting, and antennas electrical characteristics aircr...
Page 33
500 series installation manual page 4-7 190-00181-02 rev q 4.2.3 power, lighting, and antennas configuration refer to section 5.2.6 for lighting configuration. 4.2.4 power, lighting, and antennas calibration and checkout refer to section 3.9 for the com antenna checkout. 4.2.5 power, lighting, and a...
Page 34
Page 4-8 500 series installation manual rev q 190-00181-02 4.4 main indicator 4.4.1 main indicator function the main indicator displays both lateral and vertical deviation from selected course, to/from indications, lateral and vertical flags and superflags. The “cdi” key on the bezel of the gns 530 ...
Page 35
500 series installation manual page 4-9 190-00181-02 rev q 4.4.2.4 superflags pin name connector pin i/o main lateral superflag p5001 17 out main vertical superflag p5001 18 out the superflag outputs supplies not less than 500 ma on a 28 volt system and 250 ma on a 14 volt system with the output vol...
Page 36
Page 4-10 500 series installation manual rev q 190-00181-02 4.5 annunciators/switches 4.5.1 annunciators/switches function note initial certification of the 500 series units was accomplished without use of any remote switches or annunciators, since the same switching and annunciation is available on...
Page 37
500 series installation manual page 4-11 190-00181-02 rev q 4.5.1.11 ils/gps approach output the ils/gps approach output sinks 500 ma when gps navigation is selected and gps approach is active or when vloc navigation is selected and an ils channel has been selected. This output may be connected to t...
Page 38
Page 4-12 500 series installation manual rev q 190-00181-02 4.5.2.3 time mark out pin name connector pin i/o time mark out p5001 16 out time mark out outputs a 1 ms ± 1 ps wide pulse once every 1.0 s ±2 ms. Time mark out is a logic level output, capable of sourcing 1 ma at up greater than 3.8 v and ...
Page 39
500 series installation manual page 4-13 190-00181-02 rev q 4.6 serial data 4.6.1 serial data function 4.6.1.1 rs-232 the 500 series unit is capable of interfacing with other aviation instruments by transmitting rs-232 type 1 (often known as arnav format) and type 2 (often known as northstar format)...
Page 40
Page 4-14 500 series installation manual rev q 190-00181-02 4.6.1.2 arinc 429 the data output on the gps arinc 429 out port depends on the configuration (refer to section 5.2.1). Below is a list of the configurations and the labels output for each one: 1. Arinc 429 2. Gama 429 3. Gama 429 graphics 4...
Page 41
500 series installation manual page 4-15 190-00181-02 rev q label # parameter name 1 2 3 4 340 left/right hand procedure turn azimuth Ɣ Ɣ 351g distance to destination (via flight plan) Ɣ Ɣ Ɣ 352g estimated time to destination (via flight plan) Ɣ Ɣ Ɣ 371g specific equipment id Ɣ Ɣ Ɣ 377 equipment hex...
Page 42
Page 4-16 500 series installation manual rev q 190-00181-02 4.6.3 serial data configuration refer to section 5.2.1 for the main (gps) arinc 429 configuration. Refer to sections 5.2.14, 5.2.15, and 5.2.16 for the stormscope configuration. Refer to section 5.2.17 for the skywatch configuration. Refer ...
Page 43
500 series installation manual page 4-17 190-00181-02 rev q 4.7 com/vor/ils audio (gns 530 only) 4.7.1 com/vor/ils audio function activation of com mic key enables com mic audio and causes the transceiver to transmit. 500: com audio and 500: vor/ils audio are 100 mw audio outputs that are intended t...
Page 44
Page 4-18 500 series installation manual rev q 190-00181-02 4.7.2.3 com audio, vor/ils audio pin name connector pin i/o 500: com audio hi p5002 7 out 500: com audio lo p5002 19 out 500: vor/ils audio hi p5006 16 out 500: vor/ils audio lo p5006 17 out 500: com audio and 500: vor/ils audio each supply...
Page 45
500 series installation manual page 4-19 190-00181-02 rev q 4.8 vor/ils indicator (gns 530 only) 4.8.1 vor/ils indicator function note because the gns 530 includes a “cdi” button that performs switching between gps and vor/ils on a remote indicator, it is seldom necessary to use these outputs to dri...
Page 46
Page 4-20 500 series installation manual rev q 190-00181-02 4.8.2.4 flag pin name connector pin i/o vor/loc +flag p5006 3 out vor/loc -flag (vor/loc common) p5006 4 out glideslope +flag p5006 30 out glideslope +down/-flag (glideslope common) p5006 31 out the flag output is capable of driving up to t...
Page 47
500 series installation manual page 4-21 190-00181-02 rev q 4.9 rmi/obi 4.9.1 rmi/obi function the main obi output provides bearing information from the active waypoint for bendix/king serial obi devices based upon the 500 series unit’s gps navigation. For the gns 530, the main obi output may be con...
Page 48
Page 4-22 500 series installation manual rev q 190-00181-02 4.10 dme tuning (gns 530 only) 4.10.1 dme tuning function the gns 530 can channel a dme based on the tuned vloc frequency. The gns 530 outputs 2 of 5, bcd or slip parallel dme and king serial dme channeling format. When dme common is held l...
Page 49
500 series installation manual page 4-23 190-00181-02 rev q 4.10.3 dme tuning configuration refer to section 5.2.12 for the dme tuning configuration. 4.10.4 dme tuning calibration and checkout none. 4.10.5 dme tuning interconnect refer to figure f-29 on page f-59 for the king serial panel dme tuning...
Page 50
Page 4-24 500 series installation manual rev q 190-00181-02 4.11 terrain awarness and warning system (taws) and terrain the terms “taws” and “terrain” are used to identify two different configurations of 500 series unit main sub-system. The “taws” configuration complies with the terrain awareness an...
Page 51
500 series installation manual page 4-25 190-00181-02 rev q 4.11.1 taws 4.11.1.1 audio pin name connector pin i/o taws audio hi p5001 52 out taws audio lo p5001 53 in the taws audio output will be 100 mw across a 500 ohm load. 4.11.1.2 annunciators pin name connector pin i/o terrain not available an...
Page 52
Page 4-26 500 series installation manual rev q 190-00181-02 this page intentionally left blank.
Page 53
500 series installation manual page 5-1 190-00181-02 rev q 5. Post installation configuration & checkout procedure 5.1 configuration mode operations with power applied to the aviation rack and the 500 series unit turned off, press and hold the ent key and turn the unit on. Release the ent key when t...
Page 54
Page 5-2 500 series installation manual rev q 190-00181-02 data in 1, data in 2, cont. Efis/airdata selected course, heading, joystick waypoint, altitude, temperature, and speed information from the following systems: collins pro line 21 flight control selected course information from the following ...
Page 55
500 series installation manual page 5-3 190-00181-02 rev q data out selection description off no unit(s) connected to arinc 429 output arinc 429 standard arinc 429 output data (non-gama). Gama 429 arinc 429 data as defined by the general aviation manufacturers’ association (gama) general aviation su...
Page 56
Page 5-4 500 series installation manual rev q 190-00181-02 channel inputs selection description off no unit(s) connected to input of this channel. Arnav/ei-fuel serial fuel flow information from the following units: arnav fc-10, ft-10 electronics international fp-5l crossfill serial transfer of flig...
Page 57
500 series installation manual page 5-5 190-00181-02 rev q 5.2.3 main system config select the main system config page (see figure 5- 3). This page allows you to configure the fuel and terrain options. Fuel select fuel in the configure field to select the fuel type (av gas, jet a, or jet b) selectio...
Page 58
Page 5-6 500 series installation manual rev q 190-00181-02 5.2.4 main inputs page select the main inputs page (see figure 5-5). This page allows you to monitor the data on arinc 429, rs-232 and other electrical inputs. This is used for verifying electrical interfaces during installation and troubles...
Page 59
500 series installation manual page 5-7 190-00181-02 rev q source selection description photo backlight level is determined by the ambient light level as measured by the photocell on the 500 series unit. 14v dc backlight level tracks a 14 volt dc aircraft lighting bus. 28v dc backlight level tracks ...
Page 60
Page 5-8 500 series installation manual rev q 190-00181-02 slope sets the sensitivity the brightness of the display has to changes in the input level. The higher the number, the brighter the display for a given increase in the input level. This field has a range of 0 (zero) to 99, and is set to 50 a...
Page 61
500 series installation manual page 5-9 190-00181-02 rev q 5.2.8 main discrete i/o page select the main discrete i/o page (see figure 5-10). Gray code if the encoding altimeter input is used, verify that the decoded altitude field indicates the correct altitude. External switch state this allows you...
Page 62
Page 5-10 500 series installation manual rev q 190-00181-02 5.2.9 main cdi/obs config page select the main cdi/obs config page (see figure 5- 11). This page allows you to verify the main cdi outputs, both lateral (lat) and vertical (vert), and verify and calibrate the main obs input. Using the contr...
Page 63
500 series installation manual page 5-11 190-00181-02 rev q cdi (gns 530 only) selection description gps the gns 530 cdi button is in the gps state, and the gps annunciate output is active. This annunciator output may be required to be active for some installations. Vloc the gns 530 cdi button is in...
Page 64
Page 5-12 500 series installation manual rev q 190-00181-02 5.2.10 com setup page (gns 530 only) select the com setup page (see figure 5-12). These values are set at the factory and seldom require calibration. Freq selects a vhf communication frequency. For purposes of setting the squelch and sideto...
Page 65
500 series installation manual page 5-13 190-00181-02 rev q 5.2.11 vor discrete inputs page (gns 530 only) select the vor discrete inputs page (see figure 5- 13). This page allows you to verify the operation of an external vloc transfer switch that may be present in the installation. Selection verif...
Page 66
Page 5-14 500 series installation manual rev q 190-00181-02 to-from selection verify that: from the from flag is in view. Hide the to/from flag is hidden. To the to flag is in view. Selected course select 150° on the cdi/hsi that is connected to the 500 series vor/loc/gs obs inputs. The selected cou...
Page 67
500 series installation manual page 5-15 190-00181-02 rev q sdi selection description common common vor/ils receiver (only 429 data with sdi=0 is used) vor/ils 1 number 1 (pilot) vor/ils receiver. Only 429 data with sdi=0 or sdi=1 is used. Vor/ils 2 number 2 (copilot) vor/ils receiver. Only 429 data...
Page 68
Page 5-16 500 series installation manual rev q 190-00181-02 5.2.16 stormscope download data page (only if 500 series unit is configured for bfg wx-500 stormscope interface) select the stormscope download data page (see figure 5-18). This page shows raw data downloadable from the wx-500. Optional set...
Page 69
500 series installation manual page 5-17 190-00181-02 rev q 5.2.18 ryan tcad config page (only if 500 series unit is configured for ryan tcad interface) select the ryan tcad config page (see figure 5-21). This page shows the tcad’s current shield settings for the selected mode, approach mode status,...
Page 70
Page 5-18 500 series installation manual rev q 190-00181-02 5.2.21 taws audio config page 1 (only if taws is installed) select the taws audio config page 1 (see figure 5- 24). This page allows configuration of taws audio. 5.2.21.1 voice field selection description female select the female voice to a...
Page 71
500 series installation manual page 5-19 190-00181-02 rev q 5.2.21.7 edr-warning field selection description pull up sets the excessive descent rate (edr) warning alert to the specified text. (default) 5.2.21.8 ncr-caution field selection description don’t sink sets the negative climb rate (ncr) cau...
Page 72
Page 5-20 500 series installation manual rev q 190-00181-02 5.2.22.3 roc-caution field selection description caution, obstacle (2x) sets the forward looking terrain clearance (flta) reduced required obstacle clearance (roc) cautionary alert to the specified text. [default] obstacle ahead (2x) sets t...
Page 73
500 series installation manual page 5-21 190-00181-02 rev q 5.3 additional ground tests 5.3.1 connector engagement test 1. Turn on the 500 series unit, and turn on the avionics master switch (if applicable). 2. Place the 500 series unit in the rack and engage the pawl mechanism. 3. Turn the allen sc...
Page 74
Page 5-22 500 series installation manual rev q 190-00181-02 5.3.3 signal acquisition test upon approval of the instrument panel self-test page, the satellite status page is displayed. If the unit is unable to acquire satellites, relocate the aircraft away from obstructions which might be shading gps...
Page 75
500 series installation manual page 5-23 190-00181-02 rev q 5.3.6 vhf com interference check once the signal acquisition test has been completed successfully, perform the following steps: 1. View the satellite status page and verify that 7 to 8 satellites have been acquired on the 500 series unit. 2...
Page 76
Page 5-24 500 series installation manual rev q 190-00181-02 5.3.10 taws audio check (for units with taws only) while on the ground turn the 500 series unit on in configuration mode. The audio panel should also be turned on for this test. The taws audio volume has an initial default of 60% of the max...
Page 77
500 series installation manual page 5-25 190-00181-02 rev q 5.3.12 taws annunciator check (for taws external annunciator installations) while on the ground turn the 500 series unit on in configuration mode. There should also be power to the external taws annunciator unit. Note that the annunciator f...
Page 78
Page 5-26 500 series installation manual rev q 190-00181-02 3. Select "ter inhb" in the discrete toggle field on the main discrete i/o page of the 500 series unit. X verify that, when the "ter inhb" discrete toggle is selected on the 500 series unit, the "ter inhb" box is filled in on the 500 series...
Page 79
500 series installation manual page 5-27 190-00181-02 rev q 5.3.13 terrain system check (for units with terrain only) perform this verification check while on the ground. Before proceeding with this check, verify the following: x the terrain data card is inserted in the right card slot of the 500 se...
Page 80
Page 5-28 500 series installation manual rev q 190-00181-02 this page intentionally left blank.
Page 81
500 series installation manual page a-1 190-00181-02 rev q appendix a. Certification documents a.1 continued airworthiness this section provides assistance to the installing agency in preparing instructions for continued airworthiness (ica) in response to bulletin number hbaw 98-18, “checklist for i...
Page 82
Page a-2 500 series installation manual rev q 190-00181-02 6. Troubleshooting information refer to the [500 series unit] maintenance manual. 7. Removal and replacement information refer to section 3.8 of this manual. If the unit is removed and reinstalled, a functional check of the equipment should ...
Page 83
500 series installation manual page a-3 190-00181-02 rev q 19. Terrain database refer to the “400/500 series garmin display interfaces pilot’s guide addendum” for terrain database update, regionalization, and status information. A.2 500 series environmental qualification form it is the responsibilit...
Page 84
Page a-4 500 series installation manual rev q 190-00181-02 this page intentionally left blank.
Page 85
500 series installation manual page b-1 190-00181-02 rev q appendix b. Stc permission consistent with n8110.69 or order 8110.4, aviation authority approved installers are hereby granted permission to use stc #sa00864wi (gns 530/gns 530a/gps 500) data (pages b-2 and b-3) to modify aircraft. Pages b-4...
Page 86
Page b-2 500 series installation manual rev q 190-00181-02.
Page 87
500 series installation manual page b-3 190-00181-02 rev q.
Page 88
Page b-4 500 series installation manual rev q 190-00181-02.
Page 89
500 series installation manual page b-5 190-00181-02 rev q.
Page 90
Page b-6 500 series installation manual rev q 190-00181-02.
Page 91
500 series installation manual page b-7 190-00181-02 rev q.
Page 92
Page b-8 500 series installation manual rev q 190-00181-02.
Page 93
500 series installation manual page b-9 190-00181-02 rev q.
Page 94
Page b-10 500 series installation manual rev q 190-00181-02.
Page 95
500 series installation manual page c-1 190-00181-02 rev q appendix c. 500 series rs-232 aviation data format c.1 electrical interface the output signals shall be compatible with rs-232c. Data shall be generated at 9600 baud with a word length of 8 bits, one stop bit, and no parity. C.2 general outp...
Page 96
Page c-2 500 series installation manual rev q 190-00181-02 the following table describes the type 1 output sentence item designator (id) and item data (dddd) fields. If data for these sentences is invalid or unavailable, dashes ("-") are used to fill in all non-blank character positions. * the altit...
Page 97
500 series installation manual page c-3 190-00181-02 rev q c.4 output sentence type 2 the 500 series type 2 output sentence shall have the following general format: id - item designator (3 ascii characters) seq - sequence number (1 binary byte) wpt - waypoint identifier (5 ascii characters) lat - wa...
Page 98
Page c-4 500 series installation manual rev q 190-00181-02 the following table describes the type 2 output sentence item designator (id), sequence number (seq), waypoint identifier (wpt), waypoint latitude (lat), waypoint longitude (lon), and magnetic variation at waypoint (mvar) fields. Field byte ...
Page 99
500 series installation manual page d-1 190-00181-02 rev q appendix d. 500 series rs-232 fuel/air data input format d.1 electrical interface the input signals shall be compatible with rs-232c. Data shall be input at 9600 baud with a word length of 8 bits, one stop bit, and no parity. One message is ...
Page 100
Page d-2 500 series installation manual rev q 190-00181-02 d.4 shadin fuel flow sentence the garmin 500 series units shall be capable of receiving the following 55-byte message from the shadin fuel flow indicator: k0543.20100.00040.00060.00123.40045.40078.0123 where: start-transmit character (0x02) ...
Page 101
500 series installation manual page d-3 190-00181-02 rev q d.6 shadin fuel/airdata computer sentence the garmin 500 series units shall be capable of receiving the following message strings from the shadin fuel/airdata or airdata computer: d.6.1 shadin “z” format za012 "za" (ascii characters); "012" ...
Page 102
Page d-4 500 series installation manual rev q 190-00181-02 d.6.2 shadin “g” format ga012 "ga" (ascii characters); "012" represents indicated air speed (knots) gb345 "gb" (ascii characters); "345" represents true air speed (knots) gc678 "gc" (ascii characters); "678" represents mach speed (thousandth...
Page 103
500 series installation manual page d-5 190-00181-02 rev q d.6.3 shadin “s” format sa012 "sa" (ascii characters); "012" represents indicated air speed (knots) sb345 "sb" (ascii characters); "345" represents true air speed (knots) sc678 "sc" (ascii characters); "678" represents mach speed (thousandth...
Page 104
Page d-6 500 series installation manual rev q 190-00181-02 where: start-transmit character (0x02) carriage-return character (0x0d) line-feed character (0x0a) sign indicator (0x2b["+"] or 0x2d["-"]) end-transmit character (0x03) note: checksum is calculated by adding each byte in the message (includi...
Page 105
500 series installation manual page e-1 190-00181-02 rev q appendix e. 500 series lru interface overview the following tables provide a quick overview of some of the equipment that can be interfaced with the garmin 500 series units. This is not a complete listing however; it only represents those un...
Page 106
Page e-2 500 series installation manual rev q 190-00181-02 function bendix/king collins efis efis 40/50 efis-84 displays sg 465 dpu-84 function sandel ehsi sn 3308 function bendix/king collins honeywell litef litton iru/ahrs kau 461 ahc 85e laseref ltr 81 ltn 90-100 hg 1075 ab ltn-91 hg 1095 ab ltn-...
Page 107
500 series installation manual page f-1 190-00181-02 rev. Q appendix f. Drawings and interconnects f.1 introduction this section contains installation drawings to aid in the installation of the garmin 500 series unit. Additional information and notes included on the drawings can be used as reference...
Page 108
Page f-2 500 series installation manual rev. Q 190-00181-02 figure f-29—king serial panel dme tuning interconnect figure f-30—king serial remote dme tuning interconnect figure f-31—parallel 2 of 5 dme tuning interconnect figure f-32—parallel bcd/slip code dme tuning interconnect figure f-33—taws int...
Page 109
500 series installation manual page f-3 (page f-4 blank) 190-00181-02 rev q figure f-1. Ga 56 antenna installation draw ing.
Page 110
500 series installation manual page f-5 (page f-6 blank) 190-00181-02 rev q figure f-2. Gns 530 mounting rack dimensions.
Page 111
500 series installation manual page f-7 (page f-8 blank) 190-00181-02 rev q figure f-3. Gps 500 mounting rack dimensions.
Page 112
500 series installation manual page f-9 (page f-10 blank) 190-00181-02 rev q figure f-4. Gns 530 mounting rack installation.
Page 113
500 series installation manual page f-11 (page f-12 blank) 190-00181-02 rev q figure f-5. Gps 500 mounting rack assembly.
Page 114
500 series installation manual page f-13 (page f-14 blank) 190-00181-02 rev q figure f-6. 500 series recommended panel cutout dimensions.
Page 115
500 series installation manual page f-15 (page f-16 blank) 190-00181-02 rev q figure f-7. 500 series sy stem interface diagram.
Page 116
500 series installation manual page f-17 (page f-18 blank) 190-00181-02 rev q figure f-8. Gns 530/(a) ty pical installation.
Page 117
500 series installation manual page f-19 (page f-20 blank) 190-00181-02 rev q figure f-9. Gps 500 ty pical installation.
Page 118
500 series installation manual page f-21 (page f-22 blank) 190-00181-02 rev q figure f-10. Pow er, lighting, and antennas interconnect.
Page 119
500 series installation manual page f-23 (page f-24 blank) 190-00181-02 rev q figure f-11. Altimeter interconnect.
Page 120
500 series installation manual page f-25 (page f-26 blank) 190-00181-02 rev q figure f-12. Main indicator interconnect.
Page 121
500 series installation manual page f-27 (page f-28 blank) 190-00181-02 rev q figure f-13. Ki 209a main indicator interconnect.
Page 122
500 series installation manual page f-29 (page f-30 blank) 190-00181-02 rev q figure f-14. Ki 208a main indicator interconnect.
Page 123
500 series installation manual page f-31 (page f-32 blank) 190-00181-02 rev q figure f-15. Annunciators/sw itches interconnect.
Page 124
500 series installation manual page f-33 (page f-34 blank) 190-00181-02 rev q figure f-16. Rs-232 serial data interconnect.
Page 125
500 series installation manual page f-35 (page f-36 blank) 190-00181-02 rev q figure f-17. Arinc 429 efis interconnect.
Page 126
500 series installation manual page f-37 (page f-38 blank) 190-00181-02 rev q figure f-18. Arinc 429 sandel ehsi interconnect (1 500 series unit, 1 sandel sn3308).
Page 127
500 series installation manual page f-39 (page f-40 blank) 190-00181-02 rev q figure f-19. Arinc 429 sandel ehsi interconnect (2 gns 530, 1 sandel sn3308).
Page 128
500 series installation manual page f-41 (page f-42 blank) 190-00181-02 rev q figure f-20. Arinc 429 sandel ehsi interconnect (2 gns 530, 2 sandel sn3308).
Page 129
500 series installation manual page f-43 (page f-44 blank) 190-00181-02 rev q figure f-21. Arinc 429/rs-232 air data/iru/ahrs interconnect.
Page 130
500 series installation manual page f-45 (page f-46 blank) 190-00181-02 rev q figure f-22. Arinc 429 flight control interconnect.
Page 131
500 series installation manual page f-47 (page f-48 blank) 190-00181-02 rev q figure f-23. Traffic advisory sy stem interconnect.
Page 132
500 series installation manual page f-49 (page f-50 blank) 190-00181-02 rev q figure f-24. Gtx 330 interconnect.
Page 133
500 series installation manual page f-51 (page f-52 blank) 190-00181-02 rev q figure f-25. Weather and terrain interconnect.
Page 134
500 series installation manual page f-53 (page f-54 blank) 190-00181-02 rev q figure f-26. Audio panel interconnect.
Page 135
500 series installation manual page f-55 (page f-56 blank) 190-00181-02 rev q figure f-27. Vor/ils indicator interconnect.
Page 136
500 series installation manual page f-57 (page f-58 blank) 190-00181-02 rev q figure f-28. Rmi/obi interconnect.
Page 137
500 series installation manual page f-59 (page f-60 blank) 190-00181-02 rev q figure f-29. King serial panel dme tuning interconnect.
Page 138
500 series installation manual page f-61 (page f-62 blank) 190-00181-02 rev q figure f-30. King serial remote dme tuning interconnect.
Page 139
500 series installation manual page f-63 (page f-64 blank) 190-00181-02 rev q figure f-31. Parallel 2 of 5 dme tuning interconnect.
Page 140
500 series installation manual page f-65 (page f-66 blank) 190-00181-02 rev q figure f-32. Parallel bcd/slip code dme tuning interconnect.
Page 141
500 series installation manual page f-67 (page f-68 blank) 190-00181-02 rev q figure f-33. Taws interconnect.