Golmar Stadio Plus Instruction Manual - page 4
79
SYSTEM OPERATION
One building systems.
O To make a call, the visitor should key-in the three digits code corresponding to the apartment he
wishes to contact: the door panel display will show the sequence keyed-in. Once the code has
been introduced, press bell key to confirm the call: acoustic tones will be heard confirming the call
is in progress and the door panel display will show the message calling. At this moment the
call will be received at the monitor (telephone) in the dwelling. If an incorrect code has been
keyed-in, press key and try again.
In systems with several access doors, the other(s) door panel(s) will be automatically disconnected:
if a visitor tries to call from other door panel an acoustic tone will be heard confirming the system
is busy and the door panel display will show the message busy.
The call tone will be reproduced on the monitor during 3 seconds: after this time the picture will
appear on the master monitor without the visitor being aware of this. To see the picture in a slave
monitor press the push button, dissapearing the picture on the other monitor. If the call is not
answered in 45 seconds, the system will be freed.
O To establish communication pick up the monitor (telephone) handset. The communication will last for
one and a half minutes or until the handset is replaced. During the communication the door panel
display will show the message communication. Once the communication has finished the
system will be freed.
O To open the door, press the door release push button during call or communication progresses: with
one press, the door release operates during the programmed time. During the lock release
activation an acoustic tone will be heard on the door panel confirming the lock release is
activated, and the door panel display will show the message door opened.
O The monitor and telephone push buttons description is shown on pages 96, 102 and 104.
Systems with general entrance door panel(s) and several internal buildings.
O To make a call from a general entrance door panel, the visitor should key-in the five digits code
corresponding to the apartment building he wishes to contact: the door panel display will show the
sequence keyed-in. Proceed as described on the previous paragraph to establish the call progress.
The corresponding internal door panel and the other general entrance door panels (if exist): if a
visitor tries to call an acoustic tone will be heard confirming the system is busy, and the door panel
display will show the message busy. The rest of door panels are free to establish communication.
O To make a call from an internal door panel proceed as described on the previous paragraph. The
rest of internal door panels are free to establish communication. A call from the general
entrance door panel can be made to any of the internal buildings, except to the one is in
communication.
Use of the repertory names.
O If the visitor don't know the code of the apartment he wishes to contact, he could find it on the
repertory name by searching through the arrow keys. Once the code has been found, the call can
be made by pressing the bell key. Refer to page 93 for details about fast repertory searching.
Lock release activation using the access control.
O To open the door using the access control facility, press KEY symbol and one of the valid access
codes. During the lock release activation an acoustic tone will be heard on the door panel
confirming the lock release is activated, and the door panel display will show the message
door opened. If an incorrect code has been keyed-in, press key and try again. The
introduction of three wrong consecutive codes freezes the access control during 60 seconds.
80
DOORPANEL INSTALLATION
mbedding box positioning.
E
1650
1850
1450
The upper part of the door panel should be placed at 1,65m. height roughly. The hole
dimensions will depend on the number of door panel modules (see page 108).:
The door panel has been designed to be placed under most of the environmental conditions.
However it's recommended to take additional cautions like rainproof covers. To obtain
a good quality picture on video door entry systems, avoid direct incidence from light sources.
lace the embedding box.
P
Pass the wiring trough the hole made in the bottom part
of the embedding box. Level and flush the embedding
box. Once the embedding box is placed, remove the
protective labels from the attaching doorpanel holes.
1
CE7601
137
272
60
Modules
Model
W
H
D
2
CE7602
272 mm.
272 mm.
60 mm.