1. DL manuals
  2. Home Automation
  3. Receiver
  4. 12A00
  5. Installation Manual

Home Automation 12A00 Installation Manual

Manual is about: Wireless Receiver

Summary of 12A00

  • Page 1

    Home automation, inc. Model 12a00 wireless receiver installation manual document number 12i00 rev c january, 2001.

  • Page 2: Contents

    Contents description................................................................................................................ 1 compatible transmitters................................................................................ 1 installation .................................................

  • Page 3

    1 description the model 12a00 supervised wireless receiver allows up to 64 unique wireless security transmitters to report information to an omnilt, omni, or omnipro automation controller. The wireless transmitters replace wired door and window sensors, as well as wired smoke, motion, and glassbreak...

  • Page 4

    2 installation install the receiver in a central area of the premises, as high above ground as practical. The receiver should be at least 5 feet from the controller or any other electronic device. The open-air range of sx format transmitters is 3500 feet. However, building construction as follows wi...

  • Page 5

    3 operation the two operating modes of the receiver are "run" and "setup". In run mode, with the receiver connected to and communicating with the controller, the mode led should blink once per second. The receiver monitors the status of each transmitter. If the status condition of a transmitter chan...

  • Page 6

    4 setup mode the setup mode is used to configure the general operating parameters of the receiver, to program a transmitter into the receiver, and to change the characteristics of a programmed transmitter. The mode led does not blink in setup mode. To enter the setup mode: a. Press and hold the mode...

  • Page 7

    5 next, the programmed characteristics of each transmitter are displayed. The transmitter number is shown in the led display. If no transmitter is programmed for an address, neither the mode led nor the type led will be lit. If a transmitter is programmed, the mode led indicates whether the transmit...

  • Page 8

    6 transmitter setup a. Press and hold the mode/advance button for two (2) seconds. B. Enter the code (default 1111). ! To enter the first number of the code, press the set button. "c1" will appear. ! Press the mode/advance button to advance to the next code number. ! Press the set button. "c1." will...

  • Page 9

    7 reset memory to erase all transmitters from memory and to reset to the factory default configuration, press and hold both the set and mode/advance switches simultaneously for 2 seconds. You are first prompted to enter a code (as mentioned above). After the code is entered, the display will show "e...

  • Page 10

    8 the chart below shows the relationship of each wireless transmitter on the 12a00 wireless receiver to each zone on the omnilt. Zones on omnilt transmitter numbers on wireless receiver zone 09 1 17 33 49 zone 10 2 18 34 50 zone 11 3 19 35 51 zone 12 4 20 36 52 zone 13 5 21 37 53 zone 14 6 22 38 54 ...

  • Page 11

    9 connecting to omni connect the "a" & "b" terminals of the 12a00 to the "a" & "b" terminals under the section marked "consoles" on the omni controller. Connect the "+12" and "gnd" terminals of the 12a00 to the "auxiliary 12v" and "auxiliary gnd" terminals on the omni, respectively. Omni controller ...

  • Page 12

    10 the chart below shows the relationship of each wireless transmitter on the 12a00 wireless receiver to each zone on the omni. Zones on omni transmitter numbers on wireless receiver zone 17 1 17 33 49 zone 18 2 18 34 50 zone 19 3 19 35 51 zone 20 4 20 36 52 zone 21 5 21 37 53 zone 22 6 22 38 54 zon...

  • Page 13

    11 connecting to omnipro connect the "a" & "b" terminals of the 12a00 to the "a" & "b" terminals under the section marked "consoles" on the omnipro controller. Connect the "+12" and "gnd" terminals of the 12a00 to the "auxiliary 12v" and "auxiliary gnd" terminals on the omnipro, respectively. Omnipr...

  • Page 14

    12 the chart below describes where each group of wireless transmitters (groups of 16) on the 12a00 wireless receiver relates to each group of zones (groups of 16) on the omnipro in accordance with the number of addresses assigned (n1-4). Zones on omnipro (in groups of 16) zones 33-48 zones 49-64 zon...

  • Page 15

    13 fcc notice this device complies with fcc rules part 15. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Verified to compl...

  • Page 16: Quick-Reference Setup Guide

    Quick-reference setup guide to enter setup mode, press and hold the mode/advance switch for 2 seconds. Display description set switch mode/advance switch c 0 enter the first digit of the code increments the digit (0-9) advances to the next digit c 0. Enter the second digit of the code increments the...