Icom IC-FR3000 Series Sales Handbook - page 38
3-6-5
Operation Example
NOTE:
NOTE:
NOTE:
NOTE:
• All commands must be entered within 10 sec. of
entering a password. If the input time period runs
out, you must enter the password again. This time
period cannot be changed, so it is possible to
enter the password and command continuously.
• When operating from the phone line the phone
must be able to send DTMF signals.
• When the command is available from the
transceiver and phone line, the operations are not
different from both them other than the
connecting and disconnecting way to the repeater.
The following examples assume these codes
are pre-programmed in the repeater. Other
commands are the same as default codes listed on
command table (p. 36).
System Password: 0001,
Header Tone: ∗, De-limiter Tone: #
System Password OK ACK: 1111
System Control Exit ACK: 2020
OK ACK: 3333, NG ACK: 4040
1
11
1----5 OPERATION EXAMPLE
5 OPERATION EXAMPLE
5 OPERATION EXAMPLE
5 OPERATION EXAMPLE
Repeat Start
Repeat Start
Repeat Start
Repeat Start (0003 Default)
This command is available from both the transceiver
both the transceiver
both the transceiver
both the transceiver
and phone line.
and phone line.
and phone line.
and phone line. This explanation shows the step by step
operation from the transceiver or operation from the
phone line when entering the password and command
continuously (one after the other).
Repeat Stop
Repeat Stop
Repeat Stop
Repeat Stop (0004 Default)
This command is available from both the transceiver
both the transceiver
both the transceiver
both the transceiver
and phone line.
and phone line.
and phone line.
and phone line. This explanation shows the operation
from the transceiver when entering the password and
command continuously or step by step operation from
the phone line (one after the other).
▒
▒
▒
▒
▒
▒
▒
▒
▒
▒
▒
▒
▒
System control command
System control command
System control command
System control command
38
continuously (one after the other).
[From the Transceiver]
[From the Transceiver]
[From the Transceiver]
[From the Transceiver]
①
Enter the programmed password from the
transceiver.
Code: ∗0001#
• Verify the repeater replies “System Password OK
ACK (1111).”
• If the repeater replies “NG ACK (4040),” make
sure the password, header tone and de-limiter
tone are correct, and try again.
②
Enter the “Repeat Start” command within 10 sec.
Code: ∗0003#
• Verify the repeater replies “OK ACK (3333).”
• If the 10 sec. input standby time runs out, enter
the password and command continuously (Code:
∗0001#0003#).
• The repeater starts the repeater operation.
[From the Phone line]
[From the Phone line]
[From the Phone line]
[From the Phone line]
①
Dial the phone number of the phone line that the
repeater is connected to.
②
When the connection has been confirmed, enter the
following DTMF code.
Code: ∗0001#0003#
• Verify the repeater replies “OK ACK (3333).”
• If the repeater replies “NG ACK (4040),” make
sure the password, header tone, de-limiter tone
and Repeat Start code are correct, and try again.
• The repeater starts the repeater operation.
③
Hang up the phone, the repeater automatically
disconnects the phone.
the phone line (one after the other).
[From the Transceiver]
[From the Transceiver]
[From the Transceiver]
[From the Transceiver]
➥
Enter the following DTMF code from the transceiver.
Code: ∗0001#0004#
• Verify the repeater replies “OK ACK (3333).”
• If the repeater replies “NG ACK (4040),” make
sure the password, header tone, de-limiter tone
and Repeat Stop code are correct, and try again.
• The repeater stops the repeater operation.
[From the Phone line]
[From the Phone line]
[From the Phone line]
[From the Phone line]
①
Dial the phone number of the phone line that the
repeater is connected to.
②
When the connection has been confirmed, enter the
programmed password.
Code: ∗0001#
• Verify the repeater replies “System Password OK
ACK (1111).”
• If the repeater replies “NG ACK (4040),” make
sure the password, header tone and de-limiter tone
are correct, and try again.
③
Enter the “Repeat Stop” command within 10 sec.
Code: ∗0004#
• Verify the repeater replies “OK ACK (3333).”
• If the 10 sec. input standby time runs out, enter
the password and command continuously (Code:
∗0001#0004#).
• The repeater stops the repeater operation.
④
Hang up the phone, the repeater automatically
disconnects the phone.