Icom IC-FR3000 Series Sales Handbook - page 42
Operation Example
Master Enable
Master Enable
Master Enable
Master Enable (0013 Default)
This command is available from both the transceiver
both the transceiver
both the transceiver
both the transceiver
and phone line.
and phone line.
and phone line.
and phone line. This explanation shows the step
by step operation from the transceiver or operation
from the phone line when entering the password and
command continuously (one after the other).
[From the Transceiver]
[From the Transceiver]
[From the Transceiver]
[From the Transceiver]
①
Enter the programmed password from the
transceiver.
Code: ∗0001#
• Verify the repeater replies “System Password OK
ACK (1111).”
• If the repeater replies “NG ACK (4040),” make
sure the password, header tone and de-limiter tone
are correct, and try again.
②
Enter the “Master Enable” command within 10 sec.
Code: ∗0013#
• Verify the repeater replies “OK ACK (3333).”
• If the 10 sec. input standby time runs out, enter
the password and command continuously (Code:
∗0001#0013#).
• The operating repeater switches to the Master
repeater.
[From the Phone line]
[From the Phone line]
[From the Phone line]
[From the Phone line]
Slave Enable
Slave Enable
Slave Enable
Slave Enable (0014 Default)
This command is available from the transceiver and
the transceiver and
the transceiver and
the transceiver and
phone line.
phone line.
phone line.
phone line. This explanation shows the operation
from the transceiver when entering the password
and command continuously or step by step operation
from the phone line (one after the other).
[From the Transceiver]
[From the Transceiver]
[From the Transceiver]
[From the Transceiver]
➥
Enter the following DTMF code from transceiver.
Code: ∗0001#0014#
• Verify the repeater replies “OK ACK (3333).”
• If the repeater replies “NG ACK (4040),” make
sure the password, header tone, de-limiter tone
and Slave Enable code are correct, and try again.
• The operating repeater switches to the Slave
repeater.
[From the Phone line]
[From the Phone line]
[From the Phone line]
[From the Phone line]
①
Dial the phone number of the phone line that the
repeater is connected to.
②
When the connection has been confirmed, enter the
programmed password.
Code: ∗0001#
• Verify the repeater replies “System Password OK
ACK (1111).”
• If the repeater replies “NG ACK (4040),” make
42
[From the Phone line]
[From the Phone line]
[From the Phone line]
[From the Phone line]
①
Dial the phone number of the phone line that the
repeater is connected to.
②
When the connection has been confirmed, enter the
following DTMF code.
Code: ∗0001#0013#
• Verify the repeater replies “OK ACK (3333).”
• If the repeater replies “NG ACK (4040),” make
sure the password, header tone, de-limiter tone
and Master Enable code are correct, and try again.
• The operating repeater switches to the Master
repeater.
③
Hang up the phone, the repeater automatically
disconnects the phone.
• If the repeater replies “NG ACK (4040),” make
sure the password, header tone and de-limiter tone
are correct, and try again.
③
Enter the “Slave Enable” command within 10 sec.
Code: ∗0014#
• Verify the repeater replies “OK ACK (3333).”
• If the 10 sec. input standby time runs out, enter
the password and command continuously (Code:
∗0001#0014#).
• The operating repeater switches to the Slave
repeater.
④
Hang up the phone, the repeater automatically
disconnects the phone.