Kalamazoo K1000HB Use And Care Manual - Lighting Your Grill
1.800.868.1699
31
Ignition Burner
View Port
Lighting Your Grill
Before lighting your grill, be sure you have followed the instructions in this
Use and Care Guide regarding proper setup, placement, gas connections leak
testing (see page 13) and safe operation, all of which precede this page.
IMPORTANT:
Do not use the grill if the odor of gas is present at any time.
Follow leak testing procedures before using the grill.
Standard Lighting Procedure:
Main Burners
1.
Open the grill hood
2.
Pull open the Hybrid Fire Grilling Drawer approximately 2
inches so that you can easily see inside the flash tube (see
Figure 12:L page 25).
3.
Make sure all control knobs are in the OFF position.
4.
Turn the main gas supply on.
5.
Keeping your face well away from the unit, watch the end of the
flash tube (see Figure 12:L page 25). Press in the IGNITION BURNER
control knob (see Figure 18:A page 28) for 2 seconds. You should see
the electronic ignition coil glowing inside the flash tube. While continuing to
press in the control knob, turn it to the HIGH position. Ignition should take place within 4 to 5 seconds.
You will see and hear the flash at the end of the flash tube when the ignition burner ignites. If the
burner does not light within 4 to 5 seconds, turn the knob to the OFF position and wait 5 minutes for
the gas to dissipate before trying again. If you do not see the electronic ignition coil glowing inside
the flash tube, refer to the troubleshooting section of this Use and Care Guide. You can confirm the
ignition burner is operating by looking down into the grill through the view port. The view ports are
aligned with holes in the Hybrid Fire Grilling Drawers.
6.
To light any MAIN BURNER (see Figure 11:J page 25), first make sure the ignition burner is lit (see
Figure 11:K page 25) and the IGNITION BURNER control knob is at the HIGH position. Open the grill
hood. Turn any MAIN BURNER control knob to the HIGH position. Ignition should take place within 4
to 5 seconds. Watch through the grilling surface and Hybrid Fire Grilling Drawer to confirm the MAIN
BURNER is lit. If the burner does not light within this time, turn the MAIN BURNER control knob to the OFF
position and wait 5 minutes for the gas to dissipate before trying again. Each MAIN BURNER must be lit
from the IGNITION BURNER. No MAIN BURNER will light unless the IGNITION burner is burning.
Rotisserie Burner(s)
1.
Open the grill hood
2.
Make sure all control knobs are in the OFF position.
3.
Turn the main gas supply on.
4.
Keeping your face well away from the unit, press in the ROTISSERIE BURNER control knob (see Figure
18:C page 28) for 2 seconds. You should see the electronic ignition coil glowing in front of the rotisserie
burner. While continuing to press in the control knob, turn it to the HIGH position. Ignition should take
place within 4 to 5 seconds. If the burner does not light within 4 to 5 seconds, turn the knob to the OFF
position and wait 5 minutes for the gas to dissipate before trying again. If you do not see the
electronic ignition coil glowing, refer to the troubleshooting section of this Use and Care Guide.
1. Read instructions before lighting.
2. Open lid during lighting.
3. If ignition does not occur in 5 seconds, turn the burner control(s) off, wait 5
minutes, and repeat the lighting procedure.
Key to Burner Control Labels
CAUTION
Ignition Burner
Main Burner
Rotisserie Burner
Lighting Instructions
Main Burners
To light the main burners, you must first light the ignition burner.
Press in the ignition burner control and hold for 1 second.
While continuing to press in the control, turn to the HIGH position. Continue pressing
in until the burner lights. If ignition does not occur within 5 seconds, turn the ignition
burner control off, wait 5 minutes, and repeat the lighting procedure.
Once the ignition burner is lit, turn on any main burner to the HIGH position. The main
burner will light from the ignition burner. If ignition does not occur within 5 seconds,
turn the main burner controls off, wait 5 minutes, and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Rotisserie Burner(s)
Press in the rotisserie burner control and hold for 1 second.
While continuing to press in the control, turn to the HIGH position. Continue pressing
in until the burner lights. If ignition does not occur within 5 seconds, turn the
rotisserie burner control off, wait 5 minutes, and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Cooktop Burners
Press in the cooktop burner control and turn to the HIGH position. Continue pressing
in until the burner lights. If ignition does not occur within 5 seconds, turn the cooktop
burner control off, wait 5 minutes, and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Cooktop Burner
1. Read instructions before lighting.
2. Open lid during lighting.
3. If ignition does not occur in 5 seconds, turn the burner control(s) off,
wait 5 minutes, and repeat the lighting procedure.
Key to Burner Control Labels
CAUTION
Ignition Burner
Main Burner
Rotisserie Burner
Lighting Instructions
Main Burners
To light the main burners, you must first light the ignition burner.
Press in the ignition burner control and hold for 1 second.
While continuing to press in the control, turn to the HIGH position.
Continue pressing in until the burner lights. If ignition does not occur
within 5 seconds, turn the ignition burner control off, wait 5 minutes,
and repeat the lighting procedure.
Once the ignition burner is lit, turn on any main burner to the HIGH
position. The main burner will light from the ignition burner. If ignition
does not occur within 5 seconds, turn the main burner controls off, wait
5 minutes, and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Rotisserie Burner(s)
Press in the rotisserie burner control and hold for 1 second.
While continuing to press in the control, turn to the HIGH position.
Continue pressing in until the burner lights. If ignition does not occur
within 5 seconds, turn the rotisserie burner control off, wait 5 minutes,
and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Cooktop Burners
Remove the burner cover before operation.
Press in the cooktop burner control and turn to the HIGH position.
Continue pressing in until the burner lights. If ignition does not occur
within 5 seconds, turn the cooktop burner control off, wait 5 minutes,
and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Cooktop Burner
1. Read instructions before lighting.
2. Open lid during lighting.
3. If ignition does not occur in 5 seconds, turn the burner control(s) off, wait 5
minutes, and repeat the lighting procedure.
Key to Burner Control Labels
CAUTION
Ignition Burner
Main Burner
Rotisserie Burner
Lighting Instructions
Main Burners
To light the main burners, you must first light the ignition burner.
Press in the ignition burner control and hold for 1 second.
While continuing to press in the control, turn to the HIGH position. Continue pressing
in until the burner lights. If ignition does not occur within 5 seconds, turn the ignition
burner control off, wait 5 minutes, and repeat the lighting procedure.
Once the ignition burner is lit, turn on any main burner to the HIGH position. The main
burner will light from the ignition burner. If ignition does not occur within 5 seconds,
turn the main burner controls off, wait 5 minutes, and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Rotisserie Burner(s)
Press in the rotisserie burner control and hold for 1 second.
While continuing to press in the control, turn to the HIGH position. Continue pressing
in until the burner lights. If ignition does not occur within 5 seconds, turn the
rotisserie burner control off, wait 5 minutes, and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Cooktop Burners
Press in the cooktop burner control and turn to the HIGH position. Continue pressing
in until the burner lights. If ignition does not occur within 5 seconds, turn the cooktop
burner control off, wait 5 minutes, and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Cooktop Burner
1. Read instructions before lighting.
2. Open lid during lighting.
3. If ignition does not occur in 5 seconds, turn the burner control(s) off,
wait 5 minutes, and repeat the lighting procedure.
Key to Burner Control Labels
CAUTION
Ignition Burner
Main Burner
Rotisserie Burner
Lighting Instructions
Main Burners
To light the main burners, you must first light the ignition burner.
Press in the ignition burner control and hold for 1 second.
While continuing to press in the control, turn to the HIGH position.
Continue pressing in until the burner lights. If ignition does not occur
within 5 seconds, turn the ignition burner control off, wait 5 minutes,
and repeat the lighting procedure.
Once the ignition burner is lit, turn on any main burner to the HIGH
position. The main burner will light from the ignition burner. If ignition
does not occur within 5 seconds, turn the main burner controls off, wait
5 minutes, and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Rotisserie Burner(s)
Press in the rotisserie burner control and hold for 1 second.
While continuing to press in the control, turn to the HIGH position.
Continue pressing in until the burner lights. If ignition does not occur
within 5 seconds, turn the rotisserie burner control off, wait 5 minutes,
and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Cooktop Burners
Remove the burner cover before operation.
Press in the cooktop burner control and turn to the HIGH position.
Continue pressing in until the burner lights. If ignition does not occur
within 5 seconds, turn the cooktop burner control off, wait 5 minutes,
and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Cooktop Burner
1. Read instructions before lighting.
2. Open lid during lighting.
3. If ignition does not occur in 5 seconds, turn the burner control(s) off, wait 5
minutes, and repeat the lighting procedure.
Key to Burner Control Labels
CAUTION
Ignition Burner
Main Burner
Rotisserie Burner
Lighting Instructions
Main Burners
To light the main burners, you must first light the ignition burner.
Press in the ignition burner control and hold for 1 second.
While continuing to press in the control, turn to the HIGH position. Continue pressing
in until the burner lights. If ignition does not occur within 5 seconds, turn the ignition
burner control off, wait 5 minutes, and repeat the lighting procedure.
Once the ignition burner is lit, turn on any main burner to the HIGH position. The main
burner will light from the ignition burner. If ignition does not occur within 5 seconds,
turn the main burner controls off, wait 5 minutes, and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Rotisserie Burner(s)
Press in the rotisserie burner control and hold for 1 second.
While continuing to press in the control, turn to the HIGH position. Continue pressing
in until the burner lights. If ignition does not occur within 5 seconds, turn the
rotisserie burner control off, wait 5 minutes, and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Cooktop Burners
Press in the cooktop burner control and turn to the HIGH position. Continue pressing
in until the burner lights. If ignition does not occur within 5 seconds, turn the cooktop
burner control off, wait 5 minutes, and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Cooktop Burner
1. Read instructions before lighting.
2. Open lid during lighting.
3. If ignition does not occur in 5 seconds, turn the burner control(s) off,
wait 5 minutes, and repeat the lighting procedure.
Key to Burner Control Labels
CAUTION
Ignition Burner
Main Burner
Rotisserie Burner
Lighting Instructions
Main Burners
To light the main burners, you must first light the ignition burner.
Press in the ignition burner control and hold for 1 second.
While continuing to press in the control, turn to the HIGH position.
Continue pressing in until the burner lights. If ignition does not occur
within 5 seconds, turn the ignition burner control off, wait 5 minutes,
and repeat the lighting procedure.
Once the ignition burner is lit, turn on any main burner to the HIGH
position. The main burner will light from the ignition burner. If ignition
does not occur within 5 seconds, turn the main burner controls off, wait
5 minutes, and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Rotisserie Burner(s)
Press in the rotisserie burner control and hold for 1 second.
While continuing to press in the control, turn to the HIGH position.
Continue pressing in until the burner lights. If ignition does not occur
within 5 seconds, turn the rotisserie burner control off, wait 5 minutes,
and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Cooktop Burners
Remove the burner cover before operation.
Press in the cooktop burner control and turn to the HIGH position.
Continue pressing in until the burner lights. If ignition does not occur
within 5 seconds, turn the cooktop burner control off, wait 5 minutes,
and repeat the lighting procedure.
See your Use and Care Guide for manual lighting instructions.
Cooktop Burner