Lab.gruppen PLM Series PLM 10000Q Specifications - page 3
Input
Router
(Mute)
Input
Router
(Mute)
Input
Mixer 1
Input
Mixer 2
EQ
Delay
EQ
Delay
Crossovers
Output EQ
Output EQ
Output EQ
Output EQ
O
u
tp
u
t
R
o
u
ti
n
g
AMP
Attenuator
Mute
Phase Rev
Attenuator
Mute
Phase Rev
Attenuator
Mute
Phase Rev
LoadSmart
SpeakerSafe
LoadSmart
SpeakerSafe
LoadSmart
SpeakerSafe
LoadSmart
SpeakerSafe
Amp Gain
Amp Gain
Amp Gain
Amp Gain
Attenuator
Mute
Phase Rev
Module:
Gain
Phase Rev
Mute
Analog 1/2
AES 1
AES 2
Dante X
Dante Y
Analog 1/2
AES 1
AES 2
Dante X
Dante Y
AMP
AMP
AMP
ISVPL
ISVPL
ISVPL
ISVPL
LimiterMax
RMS / Peak
LimiterMax
RMS / Peak
LimiterMax
RMS / Peak
LimiterMax
RMS / Peak
Module Output:
Gain/Level
Phase Rev
Mute
Module:
Gain
Phase Rev
Mute
Module Output:
Gain/Level
Phase Rev
Mute
Module Output:
Gain/Level
Phase Rev
Mute
Module Output:
Gain/Level
Phase Rev
Mute
Ser. N:o
Removed!
CH
2
CH
CH
4
CH
3
CLASS 2 WIRING
SPEAKER OUTPUTS
INPUT
INPUT 2
LINK
LINK 2
AES/EBU
INPUT 1-2
LINK 1-2
LINK
SEC
PRIM
ACT
LINK
ACT
SWITCHED 10/100 Base-TX
Must be grounded/earthed
Made in Sweden
PIN 1: SCRN 2: POS 3: NEG
ANALOG WITH
I
SO-
F
LOAT
TM
200-240V 2500W
50-60Hz
PLM
0000Q
1
Ser. N:o
Removed!
CLASS 2 WIRING
SPEAKER OUTPUTS
INPUT
INPUT 2
LINK
LINK 2
AES/EBU
INPUT 1-2
LINK 1-2
LINK
SEC
PRIM
ACT
LINK
ACT
SWITCHED 10/100 Base-TX
Must be grounded/earthed
Made in Sweden
PIN 1: SCRN 2: POS 3: NEG
ANALOG WITH
I
SO-
F
LOAT
TM
1+/- CH 1+/-
2+/- CH 2+/-
1+/- CH 1+/-
2+/- CH 2+/-
3+/- CH 3+/-
4+/- CH 4+/-
1+/- CH 3+/-
2+/- CH 4+/-
200-240V 2500W
50-60Hz
PLM
0000Q
1
The front panel is the “local control center” for the PLM 10000Q. An intuitive, menu driven interface allows quick access to key functions
using the moisture resistant silicone touchpad. Information is clearly displayed on the daylight-readable, 2.5-inch LCD panel. The soft-button
keypad and precision rotary encoder provide control of processing and amplification functions, with key lock available.
The PLM 10000Q is available with either binding posts or an “embedded patch panel” with Neutrik Speakon connectors (2 x NLT4 and 1x
NLT8). Common connectors include; 2 x analog input XLR with switchable Iso-Float, 2 channels of AES/EBU with link-through capability for
daisy chaining, 2 x EtherCon
®
for linking or redundancy. A 32 amp PowerCon connector is used for mains supply.
This block diagram illustrates the flexible mixing and routing, as well as the powerful signal processing capabilities, offered by the
PLM 10000Q. The input section (shown in blue) allows for redundant signal paths. All settings stored here at the front end apply to system
and array files, not to individual processing modules.
Following the output routing section, however, all settings apply only to the configured input channel. These settings are then assigned to
the desired outputs via the software-controlled output routing. This innovative architecture allows one level of “global” presets (for the full
system, subsystems or arrays) with another level of presets for specific outputs or output groups.