Land Pride RCF2060 Operator's Manual - Danger
25
Section 5: Maintenance & Lubrication
10/18/16
RCF2060 and RCF2072 Rotary Cutters 326-459M
Skid Shoe Replacement
Figure 5-5
Long Term Storage
Clean, inspect, service, and make necessary repairs to
the cutter when parking it for long periods and when
parking it at the end of a working season. This will help
ensure the cutter is ready for field use the next time you
hook-up to it.
!
DANGER
Always disconnect driveline from tractor PTO shaft beforeÂ
servicing drive train and cutter blades. The PTO can beÂ
engaged if tractor is started causing bodily injury or death.
!
DANGER
Always secure equipment with solid supports before workingÂ
under it. Never work under equipment supported by concreteÂ
blocks or hydraulics. Concrete blocks can break, hydraulicÂ
lines can burst, and/or hydraulic controls can be actuatedÂ
even when power to hydraulics is off.
!
CAUTION
Always store cutter with 3-point hitch pivoted back as far asÂ
possible. The floating 3-point hitch when not hooked to aÂ
tractor can fall backwards unexpectedly causing bodily injury.
1.
Clean off any dirt and grease that may haveÂ
accumulated on the cutter and moving parts. ScrapeÂ
off compacted dirt from the bottom of deck and thenÂ
wash surface thoroughly with a garden hose. AÂ
coating of oil may also be applied to the lower deckÂ
area to minimize oxidation.
30993
Land Pride Skid Shoe Replacement Parts
Item Part No.
Part Description
1
326-221D
SKID SHOE
2
802-603C
PLOWÂ 3/8"Â - 16Â x 1" GR5
3
803-198C
NUT HEXÂ WHIZ 3/8-16 PLT
2.
Check blades and blade bolts for wear and replace ifÂ
necessary. SeeÂ
âCutter Blade MaintenanceâÂ
3.
Inspect for loose, damaged or worn parts, and adjustÂ
or replace as needed.
4.
Repaint parts where paint is worn or scratched toÂ
prevent rust. Ask your Land Pride dealer for aerosolÂ
touch-up paint. Paint is also available in touch-upÂ
bottles with brush, quarts, and gallon sizes by addingÂ
TU, QT, or GL to the end of the aerosol part number.
5.
Replace all damaged or missing decals.
6.
Lubricate as noted inÂ
 startingÂ
7.
Store cutter on a level surface in a clean, dry place.Â
Inside storage will reduce maintenance and make forÂ
a longer cutter life.
8.
Follow all unhooking instructions on page 20 whenÂ
disconnecting tractor from cutter.
Ordering Replacement Parts
Land Pride offers equipment in factory standard beigeÂ
color with black highlights. Equipment in special colorsÂ
may be purchased in Green, Red, or Orange. Because ofÂ
the variety of colors available, special attention must beÂ
given to the part number to prevent ordering the wrongÂ
replacement part. A suffix number corresponding to oneÂ
of the colors below must be added at the end of LandÂ
Prideâs part number when ordering a replacement partÂ
with that color. Parts ordered without a suffix number willÂ
be supplied in factory standard colors.
For example, if you are ordering a replacement part withÂ
part number 555-555C and the existing part is red, thenÂ
add the suffix 83 to the end of the number to make theÂ
part number read 555-555C83.
Land Pride Aerosol Touch-up Paint
Part No.
Part Description
821-011C
PAINTÂ LPÂ BEIGEÂ AEROSOL SPRAY CAN
821-002C
PAINTÂ LPÂ BLACKÂ AEROSOL SPRAY CAN
821-054C
PAINTÂ MEDIUM REDÂ AEROSOLÂ SPRAY CAN
821-058C
PAINTÂ GREENÂ AEROSOL SPRAY CAN
821-066C
PAINTÂ ORANGEÂ AEROSOL SPRAY CAN
81  . . . . . .  Green
82  . . . . . .  Orange
83  . . . . . . . Red
85  . . . . . . . Black