- DL manuals
- Lantronix
- Server
- XPort
- Integration Manual
Lantronix XPort Integration Manual
Summary of XPort
Page 1
Part number 900-310 revision f march 2005 xport™ integration guide.
Page 2
Copyright and trademark © 2005, lantronix. All rights reserved. No part of the contents of this book may be transmitted or reproduced in any form or by any means without the written permission of lantronix. Printed in the united states of america. Xport, with its patent-pending technology, is a trad...
Page 3: Contents
Xport™ integration guide 3 contents copyright and trademark _________________________________________________2 contacts ______________________________________________________________2 disclaimer and revisions _________________________________________________2 1: introduction 5 about the integration ...
Page 4: List of Figures
4 xport™ integration guide list of figures figure 2-1. Side view of the -03 xport ................................................................................... 6 figure 2-2. Xport block diagram ............................................................................................ 7 figur...
Page 5
Xport™ integration guide 5 1 1 : : i i n n t t r r o o d d u u c c t t i i o o n n about the integration guide this guide provides the information needed to test the xport™ device server on the xport evaluation board. This manual is intended for engineers responsible for integrating the xport into t...
Page 6
Xport™ integration guide 6 2 2 : : d d e e s s c c r r i i p p t t i i o o n n a a n n d d s s p p e e c c i i f f i i c c a a t t i i o o n n s s the xport embedded device server is a complete network-enabling solution enclosed within an rj45 package. This miniature serial-to-ethernet converter emp...
Page 7
Description and specifications xport™ integration guide 7 figure 2-2. Xport block diagram pcb interface the xport has a serial port compatible with data rates up to 920 kbps (in high- performance mode) for the xport-03 and greater, and at 230 kbps for the xport-01. The serial signals (pins 4–8) are ...
Page 8
Description and specifications 8 xport™ integration guide signal name xport pin # primary function cp2/dtr (configurable pin 2) 7 cp2 can be configured as follows: • modem control : dtr (data terminal ready) output driven by dstni’s built-in uart for connection to dcd of attached device. • programma...
Page 9
Description and specifications xport™ integration guide 9 ethernet interface the ethernet interface magnetics, rj45 connector, and ethernet status leds are all in the device server shell. Table 2-2. Ethernet interface signals (industry standards) signal name dir contact primary function tx+ out 1 di...
Page 10
Description and specifications 10 xport™ integration guide dimensions the xport dimensions are shown in the following drawings. Figure 2-4. Front view right led 18.25 [0.719] 16.25 [0.640] 11.55 [0.455] 7.15 [0.281] contact 1 contact 8 5.85 [0.230] 14.50 [0.571] 4.03 [0.158] 13.50 [0.531] 1.85 [0.07...
Page 11
Description and specifications xport™ integration guide 11 recommended pcb layout the hole pattern and mounting dimensions for the xport device server are shown in the following drawing. For proper heat dissipation, it is recommended that the pcb have approximately 1 square inch of copper attached t...
Page 12
Description and specifications 12 xport™ integration guide figure 2-8. Product label technical specifications table 2-4. Technical specifications category description cpu, memory lantronix dstni-ex 186 cpu, 256-kbyte zero wait state sram, 512-kbyte flash, 2-kbyte boot rom (xport-01), 16-kbyte boot r...
Page 13
Description and specifications xport™ integration guide 13 category description warranty one year limited warranty (-01 models) two year limited warranty (-03 models) included software windows™ 98/nt/2000/xp-based device installer configuration software and windows™-based com port redirector emi com...
Page 14
Xport™ integration guide 14 3 3 : : d d e e v v e e l l o o p p m m e e n n t t k k i i t t the xport development kit includes everything you need to begin to integrate the xport into your product design. Contents of the kit the development kit contains the following items: xport evaluation board xp...
Page 15
Development kit xport™ integration guide 15 valid, whether the serial interface transmit data and serial interface receive data are active, and the state of the three configurable pins, cp1, cp2, and cp3. The pld and a six-position dip switch control the evaluation board mode of operation. The switc...
Page 16
Development kit 16 xport™ integration guide xport signal xport pin # direction db9 pin # dte device signal ground 1 -- 5 gnd cts 8 in 7 rts rts 6 out 8 cts note: the supplied cd contains a configurable pins control web applet that lets you view the state of the configurable gpio pins. This applet is...
Page 17
Development kit xport™ integration guide 17 table 3-2. Configuration switch settings sw1 pos function on sw1-1 and sw1-6 on for self-test mode. (factory test) 1 off normal mode. On sw1-1 and sw1-6 on for self-test mode. (factory test) 6 off normal mode. Off xport cp1/rts (pin 6) is connected to the ...
Page 18
Development kit 18 xport™ integration guide figure 3-2. Sw1-2 on when configurable pin 1 is configured for led1, it functions as a status indicator for the serial port. Table 3-3. Cp1 status indicator condition cp1 led state idle channel solid on connected to network 4 blinks every 4 seconds cts and...
Page 19
Development kit xport™ integration guide 19 sw1-4, sw1-5 options sw1-5 controls the routing of the cp3/cts/dcd signal from the xport. Cp3 is connected to pin 8 of the xport, and you can software configure it as rts, led3, dtr, in3, or out3. With sw1-5 in the off position, the cp3 signal is routed to...
Page 20
Development kit 20 xport™ integration guide note: during a telnet connection, cp1 led (led1) is on. For a serial port connection, cp1 led (led 1) blinks for 2 seconds, then off for 2 seconds. (it appears as 4 blinks, then off for 2 seconds) cts and rts work together for hardware flow control. Config...
Page 21
Development kit xport™ integration guide 21 board layout component identification figure 3-8. Board layout fp1 xport solder pads se le c t fu n c tio n se lt t e st xp o rt p in 6 to u 2 c t s xp o rt p in 7 to u 2 d c d xp o rt p in 8 to u 2 d t r xp o rt p in 8 to u2 rt s no x p o rt pi n 8 to u 2...
Page 22
Xport™ integration guide 22 a a : : x x p p o o r r t t - - 4 4 8 8 5 5 c c o o n n n n e e c c t t i i o o n n d d i i a a g g r r a a m m the following example illustrates a connection between the xport-485 to an external transceiver ic:.
Page 23
Xport™ integration guide 23 b b : : c c o o m m p p l l i i a a n n c c e e a a n n d d w w a a r r r r a a n n t t y y i i n n f f o o r r m m a a t t i i o o n n compliance information (according to iso/iec guide 22 and en 45014) manufacturer’s name & address: lantronix 15353 barranca parkway, irv...
Page 24
Development kit 24 xport™ integration guide warranty lantronix warrants each lantronix product to be free from defects in material and workmanship for a period of one year (-01 models) or two years (-03 models). During this period, if a customer is unable to resolve a product problem with lantronix ...