1. DL manuals
  2. Lantronix
  3. Server
  4. XPort
  5. Integration Manual

Lantronix XPort Integration Manual

Manual is about: Device Server

Summary of XPort

  • Page 1

    Part number 900-310 revision g september 2009 xport™ integration guide.

  • Page 2

    Xport™ integration guide 2 copyright & trademark © 2009, lantronix. All rights reserved. No part of the contents of this book may be transmitted or reproduced in any form or by any means without the written permission of lantronix. Printed in the united states of america. Xport is a trademark of lan...

  • Page 3: Contents

    Xport™ integration guide 3 contents copyright & trademark.................................................................................................2 contacts ........................................................................................................................2 disclaimer an...

  • Page 4: List Of Figures

    Contents xport™ integration guide 4 list of figures figure 2-1 side view of the xport ..........................................................................................................6 figure 2-2 xport block diagram ..............................................................................

  • Page 5: Additional Documentation

    Xport™ integration guide 5 1 1 . . I i n n t t r r o o d d u u c c t t i i o o n n about the integration guide this guide provides the information needed to test the xport™device server on the xportevaluation board. This manual is intended for engineers responsible for integrating the xportinto thei...

  • Page 6: The Xport

    Xport™ integration guide 6 2 2 . . D d e e s s c c r r i i p p t t i i o o n n a a n n d d s s p p e e c c i i f f i i c c a a t t i i o o n n s s the xport embedded device server is a complete network-enabling solution enclosed within an rj45 package. This miniature serial-to-ethernet converter emp...

  • Page 7: Pcb Interface

    2 description and specifications xport™ integration guide 7 figure 2-2 xport block diagram pcb interface the xport has a serial port compatible with data rates up to 920 kbps (in high- performance mode). The serial signals (pins 4–8) are 3.3v cmos logic level, and 5v tolerant. The serial interface p...

  • Page 8: Ethernet Interface

    2 description and specifications xport™ integration guide 8 signal name xport pin # primary function cp2/dtr (configurable pin 2) 7 cp2 can be configured as follows: • modem control: dtr (data terminal ready) output driven by dstni’s built-in uart for connection to dcd of attached device. • programm...

  • Page 9

    2 description and specifications xport™ integration guide 9 figure 2-3 xport leds contact 1 contact 8 left led right led shield tab shield tab table 2-3 xport led functions.

  • Page 10: Dimensions

    2 description and specifications xport™ integration guide 10 dimensions the xport dimensions are shown in the following drawings. Figure 2-4 front view right led 18.25 [0.719] 16.25 [0.640] 11.55 [0.455] 7.15 [0.281] contact 1 contact 8 5.85 [0.230] 14.50 [0.571] 4.03 [0.158] 13.50 [0.531] 1.85 [0.0...

  • Page 11: Recommended Pcb Layout

    2 description and specifications xport™ integration guide 11 recommended pcb layout the hole pattern and mounting dimensions for the xport device server are shown in the following drawing. For proper heat dissipation, it is recommended that the pcb have approximately 1 square inch of copper attached...

  • Page 12: Product Information Label

    2 description and specifications xport™ integration guide 12 product information label the product information label contains important information about your specific unit, such as its product id (name), bar code, part number, and ethernet (mac) address. Figure 2-8 product label electrical specific...

  • Page 13: Technical Specifications

    2 description and specifications xport™ integration guide 13 technical specifications table 2-6 technical specification category description cpu, memory lantronix dstni-ex 186 cpu, 256-kbyte zero wait state sram, 512-kbyte flash, 16-kbyte boot rom firmware upgradeable via tftp and serial port reset ...

  • Page 14

    Xport™ integration guide 14 a a : : r r s s 4 4 2 2 2 2 / / 4 4 8 8 5 5 c c o o n n n n e e c c t t i i o o n n d d i i a a g g r r a a m m the following example illustrates a connection between the xport-485 to an external transceiver ic:.

  • Page 15

    Xport™ integration guide 15 (according to iso/iec guide 22 and en 45014) manufacturer’s name & address: lantronix 15353 barranca parkway, irvine, ca 92618 usa declares that the following product: product name model: xport embedded device server conforms to the following standards or other normative ...

  • Page 16

    B: compliance xport™ integration guide 16 rohs notice: all lantronix products in the following families are china rohs-compliant and free of the following hazardous substances and elements: • lead (pb) • mercury (hg) • polybrominated biphenyls (pbb) • cadmium (cd) • hexavalent chromium (cr (vi)) • p...

  • Page 17

    Xport™ integration guide 17 c c : : w w a a r r r r a a n n t t y y for details on the lantronix warranty replacement policy, go to our web site at www.Lantronix.Com/support/warranty ..