LEEDS WORLD PTZPRO 12 User Manual - Display : Area Titles
23
OPERATION & PROGRAMMING
DISPLAY : AREA TITLES
A zone is a pan area, defined by a left and right limit on the pan plane.
The dome system is capable of 8 area titles, each with a 12 character label.
To program a zone :
1. Press the MENU key (refer to ‘Accessing main menu’)
2. Select DISPLAY and select AREA TITLE using the joystick.
3. Use the joystick to position the cursor beside NO.xxx. Move left or right to select zone ID.
Press the [TELE] button or turn the joystick clockwise to setup START and stop pan limit angel.
4. Move the joystick to position start limit angle Press [ENT] or [OPEN] to save START limit angle.
5. Move the joystick to position stop limit angel, Press [ENT] or[OPEN] to save STOP limit angle.
6. Edit a title, See [TITLE EDIT] section for detail.
To clear an area title:
1. Press the MENU key (refer to ‘Accessing main menu’)
2. Select DISPLAY and select AREA TITLE using the joystick.
3. Use the joystick to position the cursor beside NO.xxx. move left or Right to select zone ID.
4. Press the [WIDE]or turn the joystick counterclockwise to clear area title.
Note
-after saving area titles, turn on the TITLE menu in the
-Press [ENT] or [OPEN] key to save settings and exit to previous menu.
Press [CLR] or [CLOSE] key to go to previous menu without saving any settings at any time.
█ Start Position Setup
█ Press MOVE Key
█ Save:
█ Exit:
██████████████████████████
SYSTEM >
►DISPLAY > OSD SETUP
DOME
> ►AREA TITLES
CAMERA > PRIVACY ZONE
ALARM
IMAGE SETUP
EXIT RESOLUTION
>
██████████████████████████
►NO.001 :
█• • • • • • •
TITLE
:
-START :
-STOP
:
██████████████████████████
>>>>
Twist joystick clockwise
or press [TELE] button
DISPLAY : PRIVACY ZONE
A privacy zone allows a user to program one four-sided,
user-defined area that cannot be viewed by the operator of the dome system.
The blanked area will move with pan and tilt functions and
automatically adjust in size as the lens zooms telephoto and wide.
1.Group no : Identifies group ID. Can have 1~8
2. No. xxx : Identifies privacy zone ID. Can have 1~4
3. Mode : DSABLE - disable privacy zone / BLOCK - Enable privacy zone
4. Privacy Mask : adjust mask size /3-1 : PAN/TILT - adjust position
3-2 : TELE - enlarge mask size / 3-3 : WIDE - make size small
To program a privacy zone:
1. Press the MENU key
2. Select DISPLAY and select PRIVACY ZONE using joystick.
3. Use the joystick to position the cursor beside NO.xxx. Move left or right to select zone ID.
Press the [TELE] button or turn the joystick clockwise to setup a zone.
4. Follow the instructions that appear on the screen.
5. The Privacy Zone menu reappears with a saved marked (
█) option.
To disable or clear a Privacy Zone
(a zone is enabled automatically when it is programmed):
1. Use the joystick to position the cursor beside NO.xxx.Move left or right to select zone ID.
2. Press the [WIDE] button or turn the joystick counterclockwise to clear.
Note
- Press [ENT] or [IRIS OPEN] key to save settings and exit to previous menu or
Press [Esc] or [IRIS CLOSE] key to go to previous menu without saving any
settings at any time
█ Press MOVE Key
█ Save:
█ Exit:
██████████████████████████
SYSTEM >
►DISPLAY > OSD SETUP
DOME
>
►
AREA TITLES
CAMERA > PRIVACY ZONE
ALARM
IMAGE SETUP
EXIT RESOLUTION
>>>>
Twist joystick clockwise
or press [TELE] button
>
██████████████████████████
GROUP
: 1
►NO.001 :
█• • •
MODE
: DISABLE
██████████████████████████