- DL manuals
- MEGATRONIX
- Remote Starter
- Viking VS 2000
- Installation Manual
MEGATRONIX Viking VS 2000 Installation Manual
Summary of Viking VS 2000
Page 1
Vs 2000 2-way lcd pager remote engine starter with keyless entry installation manual megatronix chatsworth, ca u.S.A. Vs 2000 install 1.
Page 2
2.
Page 3
Installation diagram h 6 3 pin white h 1 6 pin white h 8 4 pin orange h 7 8 pin black valet switch h 5 6 pin white h 4 2 pin blue dual zone shock sensor 5. Pink: ignition 2 output 2. Red: +12v input 3. Red: +12v input 4. Yellow: ignition 1 output 1. Violet: starter output 20a fuse 20a fuse 6. Brown:...
Page 4
#h5 6 pin white connector for output connection 1. White wire: (-) 200 ma programmable output dome light control output (factory default setting) or horn output or factory security rearm signal output or ground output during start (crank). 6. Orange wire: (-) 500ma grounded output when armed 4. Gray...
Page 5
Introduction installer warnings this remote starter with alarm system is designed to be installed on fuel injected vehicles only. For automatic transmission vehicle, this system must be installed and wired through a safety switch it will not start in any forward or reverse gear. Some automatic trans...
Page 6
Start cut relay (when used) violet wire closed in park or neutral only ignition switch “start” “on” neutral safety switch “acc” “off” starter h1/2 & h1/3. Red wire (2) – +12v power input remove the two 20a fuses prior to connecting these wires and do not replace them until the satellite has been plu...
Page 7
Higher level of security to the vehicle. Mount the valet switch in a hidden but accessible location. Route the valet switch wires to the control module. H5: 6-pin mini white connector wire harness: h5/1. White wire –(-) 200ma programmable output . Dome light control output (factory default setting)—...
Page 8
4. Cut (#1) wire (as shown), and connect the ignition switch side of the cut wire to terminal #87a of the relay. Connect the other side of the (#1) wire to terminal #30. 5. Connect the previously selseced resistor from terminal #87 to the second(#2) wire (as shown). To + 12 v ignition switch yellow ...
Page 9
H7/3. Violet wire – positive door switch sensing input -- this wire is the positive trigger input wire for positive door pin switch. This wire is connection for "positive" type factory door pins(typical ford motor). Locate the "common wire" for all door pins and make the connection of the violet wir...
Page 10
To test for a tach. Wire, a multi-meter capable of test ac voltage must be used. The tach. Wire will show between 1v and 6v ac at idle, and will increase as engine rpm increases. In multi-coil ignition system, the system can learn individual coil wire. Individual coil wires in a multi-coil ignition ...
Page 11
+12v master door lock switch x x splice splice cut the existing lock wire to door lock motor to slave door lock switches cut the existing unlock wire 3 pin plug to alarm 5-wire alternating door lock 30 86 87a 85 87 30 86 87a 85 87 +12v green wire blue wire vacuum operated centrol locking green wire ...
Page 12
A. Programming the remote transmitter: note: this mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is exceeded, the security system will start deleting transmitters from memory in chronological order. 1. Turn the ignition 'switch ‘off/on’ 3 times and stay in...
Page 13
Without ignition controlled door locks & unlocks ignition controlled door locks & unlocks ignition controlled door locks only ignition controlled door unlocks only 2 door lock before start and door lock after shut-down door lock before start door lock after shut-down without this feature 3 parking l...
Page 14
Exit: press any button of the transmitter to exit the password pin set up mode. Alarm feature “ iii ” proramming: 1. Turn the ignition 'switch ‘on/off’ 3 times and stay in off position. Th 2. Push the valet switch 6 times and holding in on the 6 push until three chirps with a long chirp is hearing t...
Page 15
Th 2. Push the valet switch 8 times and holding in on the 8 push until four chirps with a long chirp is hearing then release the valet switch. You are now in the start feature ‘i’ programming mode. 3. Press and release the transmitter button ‘a’ corresponding to the feature ‘a’ you want to program. ...
Page 16
Low check level hi check level 4 start / stop the system for testing & adjustment 5 - without shock sensor test mode with shock sensor test mode 6 + exit : press the button on the transmitter. A 3 long chirps & 3 parking light flashes to confirm exit. Engine checking tach. / rpm learning important n...
Page 17
B. If the engine shut down after the vehicle has been started. Button twice on the transmitter to turn ignition lights “off”. I. Press the button on the transmitter to set “check level” to low position. [1] led flash, ii. Press [1] chirp to confirm this setting iii. Repeat the step1 – 2. 3. If the c...
Page 18
1. Turn the ignition on then off 3 times and stay in off position. Th 2. Push the valet switch 12 times and holding in on the 12 push until six chirps with a long chirp is hearing then release the valet switch. You are now in the “return to factory default setting” programming mode. Alarm feature al...
Page 19
The ignition switch side of the neutral start switch. If the vehicle you are working on does not have an electrical neutral safety switch, it will be necessary to reconfigure the remote starts wiring to accommodate this vehicle. The information concerning the mechanical neutral safety switch provide...
Page 20
+ 12 v ignition key in sensor switch closes with key in ignition cylinder drivers door pin switch 87a 86 30 87 85 key in chime module connected to (-) negative safety input wire white/ black (h7/5) to hood pin switch safety shut down (h7/5) 1n4003 + 12v to connect to the key in sensor as shown in me...