MEGATRONIX Viking VS 2000 Installation Manual - page 15
th
2. Push the Valet switch 8 times and holding in on the 8 push until four chirps with a long chirp is hearing
then release the valet switch. You are now in the Start feature ‘I’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Four Chirps /
One Chirp /
Two Chirps /
Three Chirps /
Press
LED four pulse
LED one pulse
LED two pulse
LED three pulse
T
ransmitte
r
Button
Factory Default
Setting
Diesel Engine and
20 seconds warn-up
timer
Diesel Engine and
15 seconds warn-up
timer
Diesel Engine and
10 seconds warn-up
timer
Gasoline Engine
1
10 minutes run time
20 minutes run time
30 minutes run time
5 minutes run time
2
Factory alarm
disarm with channel
3 on
Without this feature
3
Constant parking
light output
Flashing parking
light output
4
5
+
Press
-
button = Activate
Remote Start.
Press
+
Press
button =
Activate Remote
Start.
button = Activate
Remote Start.
The Vehicle has
aftermarket Turbo
timer installed:
The Vehicle has
aftermarket Turbo
timer installed:
Built-in Turbo Timer
Control is Active:
Press
The system Can be
Arm with the engine
running and the
shock sensor will be
bypass for three
minutes
The system Can be
Arm with the engine
running and the
shock sensor will be
bypass as long as
the engine running.
and
buttons at the same
time to control
Engine running one
minute.
The Vehicle without
Turbo (The system
Cannot be Arm with
the engine running)
6
+
Five chirps = Built-in Turbo Timer Control is Active / Press
and
buttons at the same time to control Engine running three
minutes.
Six chirps = Built-in Turbo Timer Control is Active / Press
and
buttons at the same time to control Engine running five
minutes.
3 Hour Time start
2 Hour Time Start
7
+
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
SAFE START (Child safety mode)
Factory defaults setting to press the
button twice to start the vehicle.
Programming this feature to eliminate an accidental remote start, when kids enter this transmitter, it requires:
The user presses the transmitter
and
buttons at the same time to start the vehicle.
START FEATURE “
II
” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
th
2. Push the Valet switch 10 times and holding in on the 10 push until five chirps with a long chirp is hearing
then release the valet switch. You are now in the Start feature ‘II’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
One Chirp /
Two Chirps /
Four Chirps /
Three Chirps /
Press
LED one pulse
LED two pulse
LED four pulse
LED three pulse
T
ransmitte
r
Factory Default
Setting
Button
Exit the programming mode. (3 long chirp & 3 parking light flashes to confirm this exit.)
1
Engine Checking
TACH.
Engine Checking
Voltage
Engine Checking
OFF
+
2
RPM
learning
0.8-second (2 chirps), 1.0-second (3 chirps), 1.2-second (4 chirps),
1.4-second (5 chirps), 1.6-second (6 chirps), 1.8-second (7 chirps),
2.0-second (8 chirps), 3.0-second (9 chirps), 4.0-second (10
chirps),
3
Start Timer:
0.6-second
15